ملخص المحتوى في الصفحة رقم 1
LTC 5136 Series
Installation Instructions
®
EN AutoDome
Controllers
F.01U.284.614
ملخص المحتوى في الصفحة رقم 2
| LTC 5136 Series | Instruction Manual | Important Safeguards EN 2 11. Grounding or Polarization - This unit may be Important Safeguards equipped with a polarized alternating-current line 1. Read Instructions - All safety and operating plug (a plug having one blade wider than the instructions should be read before the unit is other). This plug will fit into the power outlet only operated. one way. This is a safety feature. If you are unable 2. Retain Instructio
ملخص المحتوى في الصفحة رقم 3
| LTC 5136 Series | Instruction Manual | FCC Information EN 3 17. Damage Requiring Service - Unplug the unit from FCC & ICES Information the outlet and refer servicing to qualified service (U.S.A. and Canadian Models Only) personnel under the following conditions: This device complies with part 15 of the FCC Rules. a. When the power supply cord or plug is Operation is subject to the following two conditions: damaged. (1) This device may not cause harmful interfer
ملخص المحتوى في الصفحة رقم 4
| LTC 5136 Series | Instruction Manual | Safety Precautions EN 4 Safety Precautions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient m
ملخص المحتوى في الصفحة رقم 5
| LTC 5136 Series | Instruction Manual | Contents EN 5 Table of Contents Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 6
| LTC 5136 Series | Instruction Manual | Unpacking EN 6 1 UNPACKING 3 DESCRIPTION This electronic equipment should be unpacked and The LTC 5136 Series Controllers are designed for use handled carefully. with the Bosch AutoDome Series cameras. They can also be used to operate any of the conventional Check for the following items: Allegiant® Series of Receiver/Drivers. • LTC 5136/61 or LTC 5136/51 Desktop The LTC 5136 Series controllers support control of all Controll
ملخص المحتوى في الصفحة رقم 7
| LTC 5136 Series | Instruction Manual | Installation EN 7 4.2 Installation Using Biphase Code 4 INSTALLATION (See Figures 3 and 4) 4.1 General interface unit in a location close Install the supplied The desktop Controller unit should be installed in a enough to the Controller unit so the that supplied location convenient to the operator. The Controller 3 m (10 ft) data cable can be used. Note that the contains a single RJ-11 connector, which is used for int
ملخص المحتوى في الصفحة رقم 8
| LTC 5136 Series | Instruction Manual | Installation EN 8 polarity sensitive. Plug the power supply into a suitable AC power source. Connect the supplied 3 m (10 ft) data cable with two RJ-11 connectors, between the Controller unit and the junction box. The orientation is not important -- either end may be connected to either device. Connect an appropriate length of cable (not supplied), Pin 1 suitable for use with RS-232 signals, between the Pin 6 LTC
ملخص المحتوى في الصفحة رقم 9
| LTC 5136 Series | Instruction Manual | Installation EN 9 signals. Connect the wire from terminal 3 to the RX 4.4 Installation Using an RS-232 Data connection of the RS-232 transmission device. Transmission Link to a Biphase Respectively, connect the wire from terminal 4 to the Camera Site (See Figure 6) data ground connection. In this application, the RS-232 data that is generated At the camera side of the RS-232 transmission device, by the Controller is connected
ملخص المحتوى في الصفحة رقم 10
| LTC 5136 Series | Instruction Manual | Setting Fast Address EN 10 • ON-998-ENTER causes all cameras, 4.5 AutoDome Camera or regardless of Fast address status, to enter the Receiver/Driver Site Configuration addressing mode. Follow the standard installation instructions provided with the AutoDome Camera or Allegiant Series Receiver/Driver unit to connect the data cable to the unit. Set the address of the AutoDome camera or receiver/driver, to the camera number that w
ملخص المحتوى في الصفحة رقم 11
| LTC 5136 Series | Instruction Manual | Controller Operation EN 11 5. Press ON-1-ENTER and the address is set. to ensure that all Controller LEDs and buttons are in Once the Fast Address is set, the switch address working order. It also automatically calibrates the (thumbwheel) is ignored. The Fast Address is center position of the analog joystick. Upon entering stored to non-volatile memory, and will not this mode, the Controller sounds a short beep. The change if pow
ملخص المحتوى في الصفحة رقم 12
| LTC 5136 Series | Instruction Manual | Controller Operation EN 12 CAMERA key: This key is only used to correct an error NUMERIC keypad: These keys are used to enter when selecting a camera number. If another key is numeric data. When the first numeric key is pressed, inadvertently pressed when a camera selection is being the LED display will become a data display and made, the Camera button may be pressed to put the indicate the numeric value pressed. Control
ملخص المحتوى في الصفحة رقم 13
| LTC 5136 Series | Instruction Manual | Technical Reference EN 13 7 TECHNICAL REFERENCE Video Monitor Video Signal Power Supply Video Adapter Signal Data DVR or Video Up to 16 biphase Converter control code outputs Switcher Unit RS-232 Data & Power Typical AutoDome Cameras or Allegiant Receiver/Driver units Controller Figure 3 Typical Camera Site Using Biphase Control Code Video Signal Video Monitor Vi
ملخص المحتوى في الصفحة رقم 14
| LTC 5136 Series | Instruction Manual | Technical Reference EN 14 Video Monitor Video Signal Power Supply Adapter RS-232 Cable or LTC 8557 Junction Box Communication Link RS-232 Data & Typical AutoDome Camera or Controller Power Allegiant Receiver/Driver unit Figure 5 Typical Installation Using RS-232 Model Camera Site Video Signal Video Monitor Video Signal Data Biphase Converter Power Data Un
ملخص المحتوى في الصفحة رقم 15
| LTC 5136 Series | Instruction Manual | Technical Reference EN 15 Pin 6 Pin 1 Pin 6 Pin 1 Figure 7 Supplied 6-Conductor 3 m (10 ft) Data Cable Detail Connector Pinouts: 1. 12V 2. Not used 3. Rx (Not used) 4. Tx 5. Signal Ground 6. 12V Pin 6 Pin 1 Figure 8 Rear Panel Controller Connector Detail 154 6.08 127 5.0 122 108 4.80 4.26 38 1.5 mm 132 in 5.2 70 mm 2.75 in
ملخص المحتوى في الصفحة رقم 16
LTC 5136 Series | Instruction Manual | Data Converter Pinouts 8 DATA CONVERTER PINOUTS Data In - 9-Pin Connector (Male) Pin Connection 1 No Connection 2 Rx 3 No Connection 4 No Connection 5 Ground 6 No Connection 7 No Connection 8 No Connection 9 No Connection KBD - RJ-11 Designations (If Used) Pin Connection 1 Output Voltage 2 Signal Ground 3 Rx 4 Ground 5 No Connection 6 Output Voltage Bosch Security Systems | 08 Ma
