GE INDOOR/OUTDOOR PIR MOTION SENSORS 60-639-43-EUR دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

 


 













   

 
Product A passive-infrared (PIR) motion sensor detects movement within a specific area by sensing the
infrared energy emitted from a body as it moves across the sensor’s field of view. When this
Summary
motion is detected, the sensor transmits an alarm signal to the control panel.
Use the indoor motion sensor to protect locations where door/window sensors are im

ملخص المحتوى في الصفحة رقم 2

Outdoor Installation Guidelines Use the following guidelines for installing outdoor motion sensors.  The outdoor motion sensor should be used for outdoor applications where there’s a tempera- ture range from 10° to 120° F (12° to 49° C).  Do not use outdoor motion sensors for intrusion protection since any human, pet, or heated mechanical motion such as an automobile can activate the sensor.  Follow the indoor motion sensor installation guidelines except for the last four items.  Do not aim

ملخص المحتوى في الصفحة رقم 3

Flush Mount Inclined Mount Corner Mount Swivel Mount Figure 5. Wall Mounting Options
Use the following procedure to mount the sensor. 1. Remove the mounting plate by depressing the button on the top of the sensor body. With the opposite hand pull the mounting plate away from the body of the sensor. 2. Punch out the mounting holes that best fit your application. See Figure 5 for wall mount options. See Figure 6 to determine which knockouts to use when mounting the motion sensor. Use the lowe

ملخص المحتوى في الصفحة رقم 4

Indoor Motion Sensor Lens Replacement 1. To change the lens, first remove the sensor from its mounting plate by depressing the button on the top of the sensor. 2. Remove the cover by depressing the two tabs on the top and the one tab on the bottom of the sensor body and sliding the cover off (see Figure 8). 3. Remove the installed lens by gently placing pressure on the lens from the outside of the lens. 4. Replace with the appropriate lens by aligning its notches with the appropriate tabs in t

ملخص المحتوى في الصفحة رقم 5

Outdoor Motion Mounting Sensor 1. Determine the desired mounting location for the sensor leaving at least four inches of room above the wall mount plate to attach the sensor. 2. Using the screws and anchors supplied, attach the wall mount plate with the opening for the swivel mount facing downward. 3. Attach the sensor assembly to the wall mount plate by screwing the sensor assembly up into the opening in the wall mount plate. 4. To remove the sensor for testing or battery replacement, slide

ملخص المحتوى في الصفحة رقم 6

l 2 AA 1.5 Vo t Batteries 1. Determine which detection zone/lens segment needs a masking label. 2. Peel the desired mask label from its backing and apply to the inside of the lens segment to be blocked. Programming Refer to the panel installation instructions for information on programming the sensor into the panel. Final Testing Final testing should be done to verify radio signal integrity and confirm control panel program- ming and response. The actual transmitter range can be determined by

ملخص المحتوى في الصفحة رقم 7

To relocate a sensor: 1. Test the sensor a few inches from the original position. 2. Increase the distance from the original position and retest until an acceptable location is found. 3. Mount the sensor in the new location. 4. If no location is acceptable, test the sensor as described below:  Test a known good sensor at the same location.  If the system does not respond, avoid mounting a sensor at that location.  If the replacement sensor functions, return the problem sensor for repair or

ملخص المحتوى في الصفحة رقم 8

Notices Approved for use in the countries marked with a check (). () Austria () Germany () Liechtenstein () Portugal () Belgium () Greece () Luxembourg () Spain () Denmark () Iceland () Netherlands () Sweden () Finland () Ireland () Norway () Switzerland () France () Italy () Poland () United Kingdom

  $ $ & ) * "