Premier Mounts UFA دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION MANUAL
UFA
Universal Flat Dual Pole Arms*
AUSTRALIA, NEW ZEALAND,
NORTH AMERICA EUROPE OCEANIA (DISTRIBUTOR)
3130 East Miraloma Avenue Swallow House, P.O. Box 295
Anaheim, CA 92806 USA Shilton Industrial Estate, Mordialloc Victoria 3195
USA and Canada – Shilton, Coventry, England CV79JY Australia
Phone: 800-368-9700 Phone: +44 (0) 2476 614700 Phone: 03 9586 6330
Fax: 800-832-4888 Fax: +44 (0) 2476 614710 www.premiermounts.com.au
Other Locations – Phone: 001.714.632.7100; Fa

ملخص المحتوى في الصفحة رقم 2

UFA Table of Contents WARNING STATEMENTS ............................................................................................................................................ - 2 - WARRANTY ................................................................................................................................................................... - 3 - PARTS LIST* .............................................................................................................

ملخص المحتوى في الصفحة رقم 3

UFA Warranty Limited Lifetime Warranty What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is only valid for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective. If Premi

ملخص المحتوى في الصفحة رقم 4

UFA Mounting Hardware (Qty 8) (Qty 8) M4 x 16 M6 x 20 M8 x 35 (Qty 8) (Qty 8) M4 x 25 M8 x 45 (Qty 8) (Qty 8) M6 x 30 (Qty 8) M5 x 12 M6 x 45 (Qty 8) M8 x 70 (Qty 4) (Qty 8) M5 x 16 M8 x 20 (Qty 8) (Qty 8) M5 x 20 (Qty 8) (Qty 8) M8 x 25 M5 x 25 (Qty 8) M5 x 50 M8 x 30 (Qty 8) (Qty 8) M6 x 16 NOTE: The nylon spacers may be stacked to achieve proper spacing. 1/4" Nylon spacers 1" Nylon spacers 5/16" Flat washers 1/2" Nylon spacers 1/4" Nylon spacers (metal) (large) (large) (small) (Qt

ملخص المحتوى في الصفحة رقم 5

UFA Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. 4. The screw length must not bypass the marking. Select anot

ملخص المحتوى في الصفحة رقم 6

UFA Support Tube Installation NOTE: Please refer to the base installation instructions for the assembly of the base and the support tubes. The support tubes and base must already be assembled. NOTE: If the optional shelf has been purchased, the shelf must be attached prior to attaching the UFA bracket arms. Please refer to the shelf installation instructions. When working with the shelf, take precautions not to scratch it. Support Tubes UFA Bracket Arm Shelf (Optional)

ملخص المحتوى في الصفحة رقم 7

UFA Installing the Display on the Support Tubes Attaching the Upper UFA Mounting Bracket WARNING: THE FOLLOWING STEPS MUST BE PERFORMED USING THREE PEOPLE. FAILURE TO DO SO WILL RESULT IN PHYSICAL DAMAGE TO THE DISPLAY AND/OR THE PERSONNEL PERFORMING THESE STEPS. 1. Two people, one on each side, must pick up the display. NOTE: In some cases, the support tubes will not voluntarily 2. Align the upper UFA mounting bracket above the two align with the upper UFA mounting bracket. In t

ملخص المحتوى في الصفحة رقم 8

UFA Attaching the Lower UFA Mounting Bracket Mounting Point Mounting Point 1. Lift the lower UFA mounting bracket up until it is 2. Line up the lower UFA mounting bracket with the mounting points that even with the display. are located on the back of the display. 3. Once the mounting points are aligned with the lower UFA mounting bracket, place a Griplate™ over each mounting point (flat side down) and secure them using the appropriate hardware (see Page 6). 4. At this time, tig