ملخص المحتوى في الصفحة رقم 1
SE-2254
Battery
2/20/40 Amp Continuous Charge
Charger
125 Amp Engine Start for 6-Volt Batteries
Model:
225 Amp Engine Start for 12-Volt Batteries
Owner's Manual With Battery Tester
–Save–
Important Safety Instructions
Read Rules for Safe Operation and Instructions Carefully
Working in vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal
battery operation. For this reason, it is of utmost importance that each time before using your charger, you
read this
ملخص المحتوى في الصفحة رقم 2
B. PERSONAL PRECAUTIONS AND SAFETY 1. WARNING: Wear complete eye protection and clothing pro- 5. Remove all personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid bat- tection, when working with lead-acid batteries. 2. Make sure someone is within range of your voice or close tery. A lead-acid battery can produce a short-circuit current high enough to weld a ring (or the like) to metal, causing a enough to come to your aid when you work with or near a
ملخص المحتوى في الصفحة رقم 3
F. OPERATING INSTRUCTIONS: CHARGING BATTERY IN VEHICLE When charging battery in the vehicle, take care to determine the battery type and which post is grounded. To reduce risk of a spark near battery, follow these steps when battery is installed in vehicle. WARNING: A spark near battery may cause battery explosion. 1. Position AC power cord and DC charging cords to reduce WARNING: Do not connect clip to carburetor, fuel lines, or risk of damage by hood, door, or moving engine parts. sheet-metal
ملخص المحتوى في الصفحة رقم 4
H. OUTPUT SELECTOR CONTROLS 6VOLTBATTERY 0 10 20 30 40 CHARGING START 12VOLTBATTERY BAD CHARGING WEAK SYSTEM GOOD GOOD Manual operation. Must be monitored. TIMER: The main function of the timer is to prevent over charg- approximately 40 amps. As the battery continues to charge, cur- ing while allowing a battery time to obtain a satisfactory charge. rent will taper to 15 to 20 amps at full charge. The Start area of To properly set the timer you must know the size of the battery the meter indicate
ملخص المحتوى في الصفحة رقم 5
I. ENGINE START 5. If the engine fails to start, charge the battery for 5 more 1. Set charge rate switch and timer to OFF positions. minutes before attempting to crank the engine again. 2. With the charger unplugged from the AC outlet, connect 6. After the engine starts, move the charge rate switch and the charger to the battery following instructions given in timer switch to OFF and unplug the AC power cord from section F. the outlet before disconnecting DC clips. 3. Plug the charger AC power c
ملخص المحتوى في الصفحة رقم 6
L. ASSEMBLY INSTRUCTIONS Wheel Charger Assembly Instructions: (Instrucciones De Armado) NOTE: Charger must be assembled before operating (Ante de la operación la unidad debe estar armada) Parts (Piezas) Tools necessary (Herramientas Necesarias) (2) 10-32 screws (tornillos de corte rosca 10-32) 5/16" wrench (Llave de 5/16") HUBS MUST 3/8" wrench (Llave de 3/8") FACE IN (2) 1/4-20 screws (tornillo de corte rosca 1/4-20) Fig. B (2) wheels(ruedas) Hammer (Martillo) Fig. C Screwdriver (Destornillador
ملخص المحتوى في الصفحة رقم 7
A. SEGURIDAD GENERAL DE ACUMULADORES 5. Quítese todos los artículos metálicos, tales como anillos, brazaletes, collares y relojes, al trabajar con un acumulador de ácido de plomo. 1. Antes de usar su cargador de acumuladores, lea todas las instrucciones Un acumulador de ácido de plomo puede producir un cortocircuito y precauciones impresas en: suficientemente fuerte para soldar un anillo (u otro objeto) a otro metal, el cargador de acumuladores causando así una quemada severa. el acumulador
ملخص المحتوى في الصفحة رقم 8
E. INSTRUCCIONES DE FUNCIONAMIENTO: CARGA DE UN (NEGRA) del cargador al extremo libre del cable. ADVERTENCIA: ACUMULADOR EN UN VEHICULO No se quede de frente hacia el acumulador al hacer la conexión final. Gire la pinza de ida y vuelta para hacer un buen contacto. Al cargar un acumulador en un vehículo, determine cuidadosamente 5. Haga todos los ajustes antes de aplicar la corriente alterna al cargador. el tipo del acumulador y cuál es el terminal de tierra. Para reducir el 6. Observe los medido
