American Standard 7440.101 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation
Instructions
7440.101
QUENTIN™
MONOBLOCK LAVATORY
FAUCET with Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
Certified to comply with ANSI A112.18.1
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect d

ملخص المحتوى في الصفحة رقم 2

INSTALL POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE Fig. A. Fig. B. 3 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCK

ملخص المحتوى في الصفحة رقم 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

ملخص المحتوى في الصفحة رقم 4

TEST INSTALLED FITTING 10 With HANDLE (1) in OFF position, turn on WATER OFF SUPPLIES (2) and check all connections for leaks. ON Remove AERATOR (3). HOT COLD 3 Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 1 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting 5 section in these instructions. Rele

ملخص المحتوى في الصفحة رقم 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

ملخص المحتوى في الصفحة رقم 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s

ملخص المحتوى في الصفحة رقم 7

™ QUENTIN MONOBLOCK LAVATORY FAUCET with Speed Connect™ Drain MODEL NUMBER 7440.101 M962682-0070A CARTRIDGE M904524 -0070A CARTRIDGE NUT M907059-YYY0A CARTRIDGE COVER M922894-YYY0A AERATOR M964156-YYY0A LIFT ROD & KNOB M918004-YYY0A A911838-0070A M952425-YYY0A SET SCREW SEAL DRAIN ASSEMBLY M964143-YYY0A HANDLE KIT M962492-0070A M962544-YYY0A MOUNTING KIT STOPPER ASSEMBLY M918462-0070A M952430-0070A CABLE ADAPTER CABLE ASSEMBLY M962457-YYY0A FLANGE M907671-YYY0A ASSEMBLY ESCUTCHEON M922872-0070A