ملخص المحتوى في الصفحة رقم 18
DRIVING THE MACHINE WARNING When using the machine for the first time it is advisable to get the feel of it by executing manoeuvres on flat ground free of foreign objects. After switching on the engine following the instructions given in the previous paragraph: 1. Move the gear lever ( fig. 2) to the 1st speed position. WARNING If the gear engages with difficulty, partially engage the clutch for an instant before trying to engage the gear again. 2. Engage the blade control level using the rela
ملخص المحتوى في الصفحة رقم 19
13. CUTTING TIPS 1. Before commencing cutting operations, read the safety instructions given in the previous sections. 2. At first the setting of a relatively high cutting height is recommended (using the relative lever in figure 2, ref. A), lowering it gradually according to working conditions. 3. Engage the blade clutch (Fig. 1, ref. A) only after having carried out the machine switch-on and gear engagement operations. 4. Before engaging the blade clutch (Fig. 1, ref. A), gradually move the a
ملخص المحتوى في الصفحة رقم 20
B2) FORWARD CONTROL CABLE Make sure that there is no play between the upper end of the cable and the adjustment screw. If there is, or if the cable has stretched, restore to ideal position using the relative adjustment screw ( Fig. 5, ref. A). If adjustment using the relative screw proves ineffective, the belts, and hence the engine mounting, must be adjusted. To perform this operation refer to section 14 C “ BELT REPLACEMENT AND ADJUSTMENT” of this manual. Figure 5 C) BELT REPLACEMENT AND ADJ
ملخص المحتوى في الصفحة رقم 1
MODEL SC121H
OPERATING AND SAFETY INSTRUCTIONS
370406 F103104A
1
ملخص المحتوى في الصفحة رقم 2
370406 F103104A 2
ملخص المحتوى في الصفحة رقم 3
- SOD CUTTER MANUAL - CONTENTS 1. USE OF THE MANUAL.........................................................................page 4 2. NOTICES ON THE MACHINE...............................................................page 5 3. TECHNICAL DATA.................................................................................page 7 4. LIFTING AND TRANSPORTATION..........................................................page 8 5. MAIN PARTS OF THE MACHINE.........................................
ملخص المحتوى في الصفحة رقم 4
OPERATING AND SAFETY INSTRUCTIONS SOD CUTTER MODEL SC121H FOREWORD This machine may only be utilized for the purpose for which it was designed, i.e. to cut 30cm-wide strips of turf. Any other use other than that stated, not covered or deducible from this Ma-nual and the enclosed Engine Manual is “PROHIBITED”. Failure to comply with instructions in this Manual and in the Engine Manual releases the manufacturer from all liability, in particular for any damage resulting from improper or incorrect u
ملخص المحتوى في الصفحة رقم 5
2. NOTICES ON THE MACHINE WARNING The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. The symbols affixed to the machine serve to warn of danger during its use and maintenance. It is vitally important to understand the meaning of the danger notices and all messages should be kept in legible condition. In the instance of wear these notices should be replaced and use of the machine suspended while witho
ملخص المحتوى في الصفحة رقم 6
370405 - Label Controls Instuction, Qty. 1 370300 - Label Instructions, Qty. 1 370406 F103104A 6
ملخص المحتوى في الصفحة رقم 7
3. TECHNICAL DATA FOR THE SOD CUTTER SC121H ENGINE : Gasoline, HONDA GX 160 K1 ENGINE CAPACITY : 5.5 Hp (4.0 kW) CUTTING WIDTH : 12” (30 cm) CUTTING HEIGHT : adjustable up to 35 mm SPEED GEARS : 2 forward gears TRANSMISSION : mechanical GEARS : in oil bath START : recoil HANDLEBARS : height-adjustable TYRES : front tyres GARDEN 3.00-4 rear tyres TRACTOR 3.00-4 DIMENSIONS L x W x H (mm) : 780 x 420 x 610 mm WEIGHT (kg) : 73 ACOUSTIC PRESSURE, measured according to EN 12733:
ملخص المحتوى في الصفحة رقم 8
4. LIFTING AND TRANSPORTATION All material is carefully checked by the manufacturer before shipping. The turf cutter is delivered in a cardboard box with the handlebars and end part of the cutting height adjustment lever disassembled. Upon receipt of the machine make sure that it has not been damaged during transit and that the packaging has not been tampered or any parts removed. Report any damage or missing parts immediately to the carrier and the manufacturer with photographic documentation.
ملخص المحتوى في الصفحة رقم 9
5. MAIN PARTS OF THE MACHINE The machine consists of the following main parts: A - BLADE CLUTCH CONTROL LEVER B - ACCELERATOR CONTROL LEVER C - FORWARD CLUTCH CONTROL LEVER D - CUTTING HEIGHT ADJUSTMENT LEVER E - ENGINE F - COVER G - BLADE H - FORWARD-NEUTRAL GEAR SELECTOR LEVER I - ON/OFF SWITCH (1/0) Figure 1 370406 F103104A 9
ملخص المحتوى في الصفحة رقم 10
6. CONTROL AND ADJUSTMENTS A) BLADE CLUTCH CONTROL LEVER This is used to engage and disengage the blade movement. Lowering the lever engages the clutch and releasing it disengages the clutch. WARNING The blade will continue to move if the engine is running and the blade clutch is engaged, regardless of the position of the forward clutch. B) ACCELERATOR CONTROL LEVER This is used to adjust the number of engine revolutions according to the operations to be carried out. Hence at switch on the leve
ملخص المحتوى في الصفحة رقم 11
I) ON SWITCH Two-position switch: (1) for starting the engine (0) for switching off the engine L) FORWARD-NEUTRAL GEAR SELECTOR LEVER This lever selects the gear forward (1st, 2nd) or neutral. WARNING Select the required gear only after disengaging the forward clutch by releasing the relative lever (Fig. 1, ref. C). 7. ASSEMBLY INSTRUCTIONS FOR THE HANDLEBARS AND END PART OF THE CUTTING HEIGHT ADJUSTMENT LEVER The turf cutter is delivered with the handlebars and the end part of the cutting heigh
ملخص المحتوى في الصفحة رقم 12
8. SAFETY INFORMATION Before using the turf cutter it is essential that the operator has understood the warnings, do’s and don’ts and precautionary measures given in this manual and in the engine manual: the prevention of injury to the operator, third parties, animals or objects directly depends on observance of these instructions. A) GENERAL INSTRUCTIONS Use of the turf cutter for purposes other than those envisaged is strictly prohibited. Climbing aboard and/or riding on the turf cutter is s
ملخص المحتوى في الصفحة رقم 13
Supervise the clothing of personnel operating the machine: a long-sleeved jacket with close-fitting cuffs, long, close-fitting trousers, heavy-duty footwear, and a protective cap or helmet should be worn. Avoid wearing loose-tailed clothing, unbuttoned jackets or torn, undone or partially zipped up items to prevent them from being caught up in the moving parts. Safety goggles and ear protection devices must be worn. Safety gloves must also be worn during machine operation and maintenance. Do
ملخص المحتوى في الصفحة رقم 14
WARNING During operation the lawn and turf are cut into strips. Should the cutter's wheels skid during use it is advisable to adjust the cutting height using the special lever (Fig. 3, ref.A). If this operation does not prevent this occurence check the state of the terrain. If it is too dry it should be wetted so that the blade encounters a slight resistance, thus making cutting operations easier. WARNING When working in a stony or obstacle-riddled area try to remove as many objects as possible
ملخص المحتوى في الصفحة رقم 15
E) AFTER USE Before moving away from the machine, place the gear lever in neutral (Fig. 2, ref. C) and switch off the engine by moving the switch (Fig.1,ref.I) to the 0 position. For greater safety shut off the feed cock (Fig. 4). 9. TRANSPORTATION OF THE MACHINE LOADING AND UNLOADING FROM A VEHICLE For transportation it is preferable to use a vehicle with an open bed. Choose firm, flat ground. Switch off the vehicle’s ignition, put into reverse gear, pull on the hand brake and block the ty
ملخص المحتوى في الصفحة رقم 16
10. DESCRIPTION OF THE SAFETY AND GUARD SYSTEMS WARNING The safety devices must never be tampered with. It is necessary to understand how they work and safeguard their efficiency and correct operation. In the instance of doubt, problems or malfunction contact your dealer. FORWARD CONTROL AND BLADE MOVEMENT LEVERS When released both of these levers instantly disengage the transmission connected to them. In this way they act as safety devices. In the instance of difficulty or sudden emergency, the
ملخص المحتوى في الصفحة رقم 17
12. STARTING AND DRIVING THE TURF CUTTER The machine can be switched on once all the aforementioned preliminary operations have been carried out. Place the feed cock in the OPEN position (direction shown by the arrow, Fig. 4). Bring the choke to the CLOSED position for a cold start (direction shown by the arrow, Fig. 4a). Set the accelerator lever at the minimum position. Grip the engine pull lead handle ( fig. 4b ) and pull gently until you feel the “bite”, then pull on the lead sharply to over
