ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Thank you for purchasing a Honda attachment for your tractor. This manual covers the assembly, operation and maintenance of the Hon- da mid-mount rotary mower for the H5013 tractor, type A2 (Two Wheel Drive Model) and A4 (Four Wheel Drive Model). Read this manual and the Owner’s Manual for the honda H5013 Tractor before you operate the rotary mower. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this pu
ملخص المحتوى في الصفحة رقم 4
CONTENTS ....................................................... 3 1. SAFETY INFORMATION ................................................................. 9 2. SERIAL NUMBER 10 3. COMPONENT IDENTIFICATION ............................................. .......................................................... 11 4. INSTALLING MOWER 11 .................................................................... 1. Loose parts 12 2. How to measure hardware and components ......................
ملخص المحتوى في الصفحة رقم 5
1. SAFETY INFORMATION Read all safety instructions before operating. DISCHARGE GUARD WHILE BLADE IS TURNING. AWAY FROM MOWER AND DISCHARGE GUARD WHILE BLADE IS TURNING. 3
ملخص المحتوى في الصفحة رقم 6
SAFETY INFORMATION For your safety and the safety of others, pay special attention to these precautions: Operator Responsibility Keep the tractor in good operating condition. Operating a tractor in poor, or questionable condition could result in serious injury. Be sure all safety devices are in working order and warning labels are in place, these items are installed for your safety. Know how to stop the engine and attachments quickly in case of emergency. Understand the use of all contr
ملخص المحتوى في الصفحة رقم 7
Fire and Burn Hazard Gasoline is extremely flammable, and gasoline vapor can explode. Use extreme care when handling gasoline. Keep gasoline out of reach of children. l Refuel in a well ventilated area with the engine stopped. l Allowed the engine to cool before refueling. Fuel vapor or spilled fuel may ignite. l The accumulation of dry grass and leaves around the engine, the ex- haust system, or on top of the cutter deck (especially around the pulleys) may ignite. l It is illegal in s
ملخص المحتوى في الصفحة رقم 8
Thrown Object Hazard Objects hit by the blades can be thrown from the tractor with great force, and may cause serious injury. Before mowing, clear the mowing area of sticks, stones, dog bones, and other litter and loose objects. Mow only in daylight, or in well-lit areas at night, so you can see and avoid objects in the grass. Before operating the tractor, be sure the side discharge guard is down, or that the optional grass catcher bags and discharge chute are in place. Disengage the Pow
ملخص المحتوى في الصفحة رقم 9
l To avoid injury to yourself and others, before leaving the Tractor unat- tended, ALWAYS, - park on level ground. - disengage the power take-off. - lower the attachment(s). - Lock the parking brake. - stop the engine. - and remove the key. l Be sure to follow the instructions below whenever applying the dif- ferential lock. - Be sure that the main transmission lever is set in 4th gear or lower, and reduce engine speed before applying the differential lock. - Do not apply while t
ملخص المحتوى في الصفحة رقم 10
MAINTENANCE SAFETY l Before performing maintenance/inspection, read the instructions thoroughly. l Before cleaning, inspecting or servicing the tractor, be sure to - Turn off and lower any attachments. - Stop the engine and remove the key. - Remove the spark plug cap. l If you hit an object, stop the engine and inspect the Tractor and its at- tachments. Fix any damage before you resume operation. l Operating the tractor with damaged, worn or broken parts may result in severe personal i
ملخص المحتوى في الصفحة رقم 11
2. SERIAL NUMBER The serial number is used to identify your rotary mower and may be re- quired by the dealer when ordering replacement parts. The serial number is located on the right side of the deck. Record the number here for your reference. NO. SERIAL NUMBER 9
ملخص المحتوى في الصفحة رقم 12
3. COMPONENT IDENTIFICATQON GAUGE WHEELS DISCHARGE COVER I ANTI-SCALP ROLLERS BLADES IO
ملخص المحتوى في الصفحة رقم 13
4. INSTALLING MOWER l The rotary mower should be installed by an authorized Honda dealer unless the owner has proper tools and feels he is mechanically qualified. l To prevent accidental start-up, remove the ignition switch key, and disconnect the spark plug cap before installing the mower. Install with the tractor on level ground. Lock the parking brake, set the transmission lever in “N” (Neutral) and the front and rear P.T.O. levers in the “OFF” positions. 1. Loose parts The parts ca
ملخص المحتوى في الصفحة رقم 14
ONT DECK LINKS EAR DECK LINK LOCK PIN DISCHARGE COVER 1 DRIVE BELT FLANGE FLANGE BOLT BOLT 4 4 8xl6mm 8xl6mm FLANGE BOLT LEVER BOLT V-BET DRIVEN STOPPER (Belt Stopper B) (Belt Stopper A) 2. How to measure hardware and components: MILLIMETERS ~~~~,~~~~,~~,,,~,,,~,,,,,,,,,~,,,,,,,,I~Il~II~IIII~l’ll~Ill’~llll~llll~llll~llll~llll~llll~llli~l~ll~llll~llll~llll~llll~llll~llll~ I 0 10 20 30 40 50 60 70 80 90 100 110 120 130 0 LENG 0 0 o o 5mm 8mm 12 mm 14 mm 16 mm PLAIN WASHERS
ملخص المحتوى في الصفحة رقم 15
3. Installation of front tensioner bracket - 1 Remove and retain the six 8 x 20 mm flange bolts, three on each side, from the tractor frame, front hitch pivots. FLANGE BOLTS Bx20mm FRONT HlTdH PIVOT A - 2. Remove and retain the lower cover B by removing the 8 x 16 mm flange bolts. TS LOWER CbVER B 13
ملخص المحتوى في الصفحة رقم 16
- 3. Install the drive pulley on the front P.T.O. shaft using an 8 x 20 mm special flange (shouldered) bolt. Tighten the bolt to the specified torque. Torque specification: 2.2 kg-m (16 ft-lb) SPECIAL FLANGE BOLT 8 x 20 mm - 4. Position the front tensioner bracket on the frame and install using four of the bolts removed in Step 2. Tighten the bolts to the specified torque. Retain the remaining two bolts. Torque specification: 2.2 kg-m (16 ft-lb) FLANGE BOLTSBx16mm FRONT TENSl6NER BRAC
ملخص المحتوى في الصفحة رقم 17
- 5. Insert the end of the tensioner spring into the hole in the tensioner arm. Hook the another end against the frame. TENSIONER SPRING - 6. Install the front hitch pivot A removed in Step 1 on the frame from the inside. Install the tensioner guard on the frame from the outside as shown, using the six 8 x 20 mm flange bolts removed in Step 1, and tighten to the specified torque. Torque specification: 2.2 kg-m (16 ft-lb) FRONT HITCH PIVOT A FLANGE BOLTS Bx20mm TENSIONER GUARD 15
ملخص المحتوى في الصفحة رقم 18
4. Installation of lift link - 1 Pump grease through the grease fitting to lubricate the lift arm shaft. Insert the lift arm shaft through the bracket on the main frame from the left side. Adjust the length of the deck lift rod to 370-372 mm (14.6- 14.6 in), then tighten the nut securely. Install the deck lift rod in the hole in the lift arm bracket. Place the plain washer over the end of the deck lift rod and insert the lock in through the end. Recommended Grease: Multipurpose Grease PL
ملخص المحتوى في الصفحة رقم 19
- 3. Slide the right and left link pivots in the holes in the frame from the inside, and install using three 8 x 20 mm flange bolts for each pivot. Slide the lift link shaft through the holes in the pivots as shown. Recommended Grease: Multipurpose Grease FLANGE BOLTS Bx20mm LIFT LINK SHAFT LIFT LINK PIVOT - 4. Slide the lift link assembly onto the lift link shaft on the main frame, and install the lock washer over the end of the lift link shaft. Insert the pin through the end of the
ملخص المحتوى في الصفحة رقم 20
5. Installation of cutter deck n Cutter deck assembly - 1. Install the discharge cover using two self-locking nuts; tighten nuts to specified torque: Torque specification: 2.2 kg-m (16 ft-lb) SELF-LOCKING NUTS t DISCHARGE COVER - 2. Adjust the length of the cutter deck lift plates to 150- 152 mm (5.9-6.0 in.), then tighten the nuts securely. Install the cutter deck lift plates on the cutter deck with 14 mm plain washers and lock pins (gold). Install the rear deck links on the cutter
