ملخص المحتوى في الصفحة رقم 1
Safety Instructions & Operator’s Manual for
REAR ENGINE RIDING MOWER
SERIES 19
MODEL
M250819BE
M280919B
M281019BE
M300919B
M301019BE
MODEL NUMBER EXPLANATION
M 28 10 19 B E
MIDDLE MARKET ENGINE OPTIONS
CUTTING WIDTH ENGINE TYPE
ENGINE HP SERIES DESIGNATION
M - Middle Market 25 - 25” Cutting Deck 08 - 8.0 HP Engine 19 - Series B - Briggs Engine E - Electric Start
28 - 28” Cutting Deck 09 - 9.0 HP Engine Designation
30 - 30” Cutting Deck 10 - 1
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) (Continued From Previous Column) 7. Keep people and pets out of mowing area. 14. Exercise CAUTION when pulling loads. Limit Immediately STOP blades, STOP engine, and loads to those you can safely control and attach STOP machine if anyone enters the area. loads to hitch plate as specified with SNAPPER 8. Check shields, deflectors, switches, blade attachment instructions. controls and other safety devic
ملخص المحتوى في الصفحة رقم 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.......................................................... 2-3 TABLE OF CONTENTS...................................................................................... 4 SECTION 1 - FAMILIARIZATION ....................................................................... 5 SECTION 2 - OPERATING INSTRUCTIONS................................................. 6-11 Pre-start Checklist ..................................................................
ملخص المحتوى في الصفحة رقم 5
Section 1 - FAMILIARIZATION FUEL FILLER CAP VENT OPERATOR’S FUEL TANK SEAT STEERING WHEEL ENGINE SPEED CONTROL REAR BUMPER DECK LIFT LEVER CLUTCH/BRAKE PEDAL TRANSMISSION SHIFT LEVER MOWER BELT COVER DISCHARGE DEFLECTOR BLADE LEVER BLADE PEDALS PARK BRAKE MOWER LATCH DECK FIGURE 1.1 1.1 INTRODUCTION 1.2 NOMENCLATURE This manual has been prepared for the operator’s of the The nomenclature drawing above, Figure 1.1, shows the SNAPPER Rear Engin
ملخص المحتوى في الصفحة رقم 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 OPERATOR’S SEAT ADJUSTMENT Make the following checks and perform the service 2.2.1. FRONT TO REAR ADJUSTMENT required before each start-up. 1. With the engine stopped, loosen the two adjusting 2.1.1. Check tires and add or release air as needed knobs and move seat to desired position. After to bring pressure to 12 psi in front and 12 psi in rear adjustment, tighten knobs securely. If seat does not tires. move after loo
ملخص المحتوى في الصفحة رقم 7
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION TO START ENGINE, 2.3.1. ENGINE (ELECTRIC START) PUSH CLUTCH/BRAKE IMPORTANT: When the ignition key is turned to PEDAL ALL THE WAY “START”, the engine will turn over, but will not start DOWN unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.5).The operator should be in the seat. Start engine as follows: 1. Move transmission shift lever to (N) Neutral position
ملخص المحتوى في الصفحة رقم 8
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 5. Move engine speed control to the choke position 2.3.1. ENGINE (ELECTRIC START) (Continued) to start a cold engine. See Figure 2.6 8. Should the battery be too weak to start the engine, 6. Turn key to “RUN” position. See Figure 2.9. Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines. 2.3.2. ENGINE (MANUAL START) IMPORTANT: When the ignition key is turned to “RUN”, and the recoil handle
ملخص المحتوى في الصفحة رقم 9
Section 2 - OPERATING INSTRUCTIONS WARNING WARNING Once blade is disengaged, it should come to a DO NOT operate blades in reverse. STOP BLADES. complete stop in 3 seconds or less. If the blade LOOK and SEE behind and down for children, pets continues to rotate after 3 seconds, the blade brake and hazards before and while backing. must be adjusted. Refer to Section “BLADE BRAKE DEPRESS ADJUSTMENT” for adjustment procedures or return CLUTCH/BRAKE machine to an authorized SNAPPER deal
ملخص المحتوى في الصفحة رقم 10
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT leave machine with the engine running. CLUTCH/BRAKE Stop engine. Stop blade. Shift to neutral. Engage PEDAL parking brake. Remove key. 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE 1. Stop engine by turning key to the “OFF” position. See Figure 2.13. TURN TO “OFF” POSITION PARK BRAKE LATCH SHOWN ENGAGED KEY FIGURE 2.14 BLADE LEVER (SHOWN IN “OFF” POSITION) FIGURE 2.13 BLADE PEDALS 2.4.2. WHEEL
ملخص المحتوى في الصفحة رقم 11
Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.5. CUTTING HEIGHT ADJUSTMENT 2.4.4. PARK BRAKE 1. Adjust cutting height as desired to any one of 1. Engage park brake by pushing clutch/brake pedal five positions using deck lift lever. Move deck lift lever up or down to desired cutting height and then “DOWN” and moving the park brake latch to the move over to secure in the height of cut notch. “ENGAGED” position. While holding the park brake latch “ENGA
ملخص المحتوى في الصفحة رقم 12
Section 3 - MAINTENANCE 5. After all the oil has drained, close the drain and WARNING wipe up any oil that may have spilled. See Figure 3.1. DO NOT attempt any adjustments, maintenance, Dispose of used oil properly. service or repairs with the engine running. STOP 6. Fill engine crankcase with new oil. Refer to your engine. STOP blade. Engage parking brake. Remove engine owner’s manual for oil specifications. key. Remove spark plug wire from spark plug and secure away from plug.
ملخص المحتوى في الصفحة رقم 13
Section 3 - MAINTENANCE 3.2.5. BLADE BRAKE WARNING 1. Check blade brake for proper function. Blade should DO NOT attempt any adjustments, maintenance, service or stop rotating in 3 seconds or less after moving the blade repairs with the engine running. STOP engine. STOP blade. control lever to the “OFF” position or after releasing the Engage parking brake. Remove key. Remove spark plug blade pedals. wire from spark plug and secure away from plug. Engine and components are HOT. Avoi
ملخص المحتوى في الصفحة رقم 14
Section 3 - MAINTENANCE 3.2.8. LUBRICATION – GREASE FITTINGS The following components on the Rear Engine IMPORTANT: If the Rear Engine Rider will be on its Rider are equipped with grease fittings and rear bumper for longer than two hours, remove the require periodic lubrication. Apply General battery. Refer to Section “BATTERY REMOVAL”. Purpose grease (NLGI No.2) with a grease gun. 1. Front Wheel Bearings. Refer to Section 3.3.6. MOWER DECK LINKAGE - LUBRICATION “FRONT WHEEL BEARING
ملخص المحتوى في الصفحة رقم 15
Section 3 - MAINTENANCE 3.3 SERVICE - EVERY 25 OPERATING HOURS DIFFERENTIAL 3.3.8. REAR AXLE BEARING 1. The left rear axle bearing requires three shots of general purpose grease from grease gun. See Figure 3.7. NOTE: Some models are equipped with a pre- lubricated sealed bearing and require no additional lubrication. FILL/LEVEL 2. The right rear axle bearing is lubricated by the PLUG P.N. 1-1024 differential lubricant and requires no grease. LEFT REAR AXLE BEARING GREASE F
ملخص المحتوى في الصفحة رقم 16
Section 3 - MAINTENANCE 3.4 SERVICE - ANNUALLY WARNING 3.4.1. Perform all maintenance as specified in “MAINTENANCE SCHEDULE” Section of this manual. DO NOT attempt any adjustments, maintenance, service 3.4.2. FUEL FILTER or repairs with the engine running. Stop engine. Stop Service fuel filter as instructed below, on COLD blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from ENGINE ONLY! plug. Engine and components are HOT. Avoid serio
ملخص المحتوى في الصفحة رقم 17
Section 4 - ADJUSTMENTS & REPAIR 4. If the distance is less than 1”, adjust belt tension. WARNING 5. Remove hairpin and flat washers from pivot stud. DO NOT attempt any adjustments, maintenance, See Figure 4.2. service or repairs with the engine running. Stop 6. Pull front frame forward until distance between engine. Stop blade. Engage parking brake. Remove belt, with blade lever “ON”, measures 1-1/4”. key. Remove spark plug wire from spark plug and secure away from plug. Engine an
ملخص المحتوى في الصفحة رقم 18
Section 4 - ADJUSTMENTS & REPAIR WARNING 1/8” TO 1/4” Once blade is disengaged it should come to a stop in 3 seconds or less. If the blade continues to rotate BLADE LATCH LEVER PLATE after 3 seconds the blade brake must be adjusted. DO NOT continue to operate the machine if the blade brake is not operating properly. 4.2.2. BLADE BRAKE ADJUSTMENT The automatic Blade Brake should stop the blades within 3 seconds anytime the blades are disengaged by moving blade lever to the "OFF"
ملخص المحتوى في الصفحة رقم 19
Section 4 - ADJUSTMENTS & REPAIR WARNING FLOOR DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop FRONT engine. Stop blade. Engage parking brake. Remove REAR key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are X-1/8” HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. HANGER 4.2.3. MOWER DE
ملخص المحتوى في الصفحة رقم 20
Section 4 - ADJUSTMENTS & REPAIR 7. Adjust cable up or down using the jam-nuts to obtain a distance of 1/2” to 3/4” between end of WARNING clutch/brake cable (adjustment shown in inset of Figure 4.9) and bottom of housing. See Figure 4.9. DO NOT attempt any adjustments, maintenance, 8. After adjustment is complete, securely tighten service or repairs with the engine running. Stop cable jam-nuts. engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark
