ملخص المحتوى في الصفحة رقم 1
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Triple Catcher
Clean Sweep Triple Catcher
Mfg. No. Description
5900703 Clean Sweep Triple Catcher
1735596
Rev. 00
Rev. Date 10/2007
TP 100-4785-00-AT-SMAN
ملخص المحتوى في الصفحة رقم 2
THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)
ملخص المحتوى في الصفحة رقم 3
Table of Contents Safety Rules & Information Cover and Bag Installation General Warnings............................................2 Install Cover Assembly ....................................7 Safety Decals ..................................................2 Install Collector Bags.......................................7 Storing the Grass Catcher...............................3 Tube Installation Lower Tube Installation....................................8 General Operating Information Before Op
ملخص المحتوى في الصفحة رقم 4
Safety Rules and Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS • Know the unit’s controls and how to stop quickly. tears, holes, or weak spots and replace with a new READ THE OPERATOR’S MANUALS. bag that meets manu
ملخص المحتوى في الصفحة رقم 5
General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
ملخص المحتوى في الصفحة رقم 6
Tube Component Assembly BAFFLE INSTALLATION 44” Mower Deck 50” Mower Deck 1. Determine which baffle to use (See Chart). RH side RH side 2. Lift side discharge chute (H, Figure 1). “A” 26-1/4” long 29-3/4” long 3. Insert baffle (F) through discharge opening and posi- LH side LH side tion baffle into place. “B” 24-7/8” long 27-3/4” long 4. Tighten carriage bolts (A) and locknut(s) (E) on baffle (F). “A” 5. Tighten carriage bolt (B) and locknut(s) (E) on baffle (F). 6. Position baffle (G) into plac
ملخص المحتوى في الصفحة رقم 7
Component Installation C B A D A C E F B G G H J I Figure 2. Install Mounting Plate A. Mounting Plate Figure 3. Lower Chute to Boot Installation B. Locknuts, 5/16-18 A. Latch Pin C. Carriage Bolts, 5/16-18 x 5/8 B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 Component Installation D. Lower Chute E. Locknut, Center Lock, 5/16-18 INSTALL MOUNTING PLATE F. Rubber Strap 1. Install mounting plate (A, Figure 2) to mower deck as G. Locknuts, Whiz Lock, 5/16-18 shown. Secure with carriage bolts (C
ملخص المحتوى في الصفحة رقم 8
Bag and Cover Support Installation INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 5) to B upright support (A) using the capscrews (C) and the locknuts (D). D A C Figure 5. Install Bag and Cover Support A. Upright Support B. Bag and Cover Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16 6
ملخص المحتوى في الصفحة رقم 9
Cover and Bag Installation INSTALL COVER ASSEMBLY INSTALL COLLECTOR BAGS 1. Attach cover assembly (B, Figure 6) to bag support 1. Raise the cover (A, Figure 7). bracket (A) using hinge pivots (E). Secure cover Note: It may be necessary to fold seat forward to allow using cover hinge pins (C) and hair pins (D). cover to stay in the raised position. 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). A C D B E C D B E A D C Figure 6. Install Cover Assembly Figure 7.
ملخص المحتوى في الصفحة رقم 10
Tube Installation LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 8). 2. Insert lower chute rod (A) into mounting plate (B). D 3. Pull rubber strap (C) and secure by placing hole closest to knob in strap completely over locknut (E). C B C D A E Figure 9. Install Upper Tube to Cover A. Upper Tube B. Cover C. Ridge, Upper Tube D. Ridge Cutout A 44” Frame Hung Mowers B 50” Frame Hung Mowers 44” Free Floating Mowers E D Figure 8. Install Lower Tube A. Lower Chute Rod F B. Mounti
ملخص المحتوى في الصفحة رقم 11
Collector Installation and Removal E F R Q D C G A B D C P O H A. Hitch Support Assembly J. Deflector I J B. Cover K. Nut & Capscrew N K C. Pins L. Mounting Plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute M F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge L I. Strap, Boot R. Ridge Cutout Figure 11. Collector Installation and Removal COLLECTOR INSTALLATION COLLECTOR REMOVAL Note: See previous pages for more detailed installation WARNING and operation
ملخص المحتوى في الصفحة رقم 12
Carrier Installation FRONT WEIGHT CARRIER INSTALLATION C 1. Install carrier (F, Fgure 12) as shown securing with A capscrews (B), and locknuts (C). 2. Secure required weights using rod (D) and safety C clip (E). B A B F E D E Figure 12. Front Weight Carrier Installation A. Holes D. Rod B.Capscrews, E.Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknuts, 1/2-13 10
ملخص المحتوى في الصفحة رقم 13
Hitch Plate and Back Plate Installation FLAT STYLE BUMBER TUBE STYLE BUMBER 1. Remove and discard hardware holding heat shield 1. Center and secure hitch plate (A, Figure 14) to the (B, Figure 13) to upper and lower bumper (E). bumper (B) with u-bolts (C) and locknuts (D). 2. Open existing holes (F) in heat shield (B) and upper 2. Set the back plate and support (A, Figure 15) onto & lower bumper (E) to 17/32”. pins of hitch plate (C). Secure with rod (D) and hair pin (B). 3. Install hitch plat
ملخص المحتوى في الصفحة رقم 14
Grass Catcher Removal an d Attachment Note: Back plate (A, Figure 18) will fall when rod (D) REMOVING THE GRASS CATCHER is removed. 1. Remove the hair pin clips (B, Figure 16) and hinge 3. Remove the hair pin (B, Figure 18) and rod (D) pins (D) and remove the cover (A). while holding back plate (A). 4. Lift the back plate and support (A) off hitch plate A (C). A B C D B C D Figure 16. Remove the Cover A. Cover C. Hinge B. Hair Pin Clip E. Hinge Pin Figure 18 . Install Back Plate (Flat Style
ملخص المحتوى في الصفحة رقم 15
Grass Catcher Removal and Attachment ATTACHING THE GRASS CATCHER A 1. Set the back plate and support (A, Figure 19) onto B the pins of the hitch plate (C). Secure with rod (D) and hair pin (B). 2. Hook the bags on the back plate (Figure 7). C 3. Install the catcher cover (A, Figure 7) and secure with the hinge pins (D, Figure 6) and hair pin clips (D). D Note: Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened. 4. Insert lower chute (A, Figure 1
ملخص المحتوى في الصفحة رقم 16
MANUFACTURING, INC. Simplicity Mfg. Inc.500 N Spring Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Street / PO Box 997 Port Washington, WI 53074-0997 Port Washington, WI 53074-0997 www.AGCOLawn.com www.SimplicityMfg.com Simplicity Mfg. Inc. - Snapper Products Simplicity Mfg. Inc.500 N Spring 535 Macon Street Street / PO Box 997 McDonough, GA 30253 Port Washington, WI 53074-0997 www.Snapper.com www.MasseyLawn.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & St
