ملخص المحتوى في الصفحة رقم 1
POWERED MIXERS
From Fender Pro Audio
Owner's Manual for
SRM 6302 / 8302
P/N 050804
REV A
6302 / 8302
6302 / 8302
ملخص المحتوى في الصفحة رقم 2
Fender Musical Instruments 7975 North Hayden Road, Scottsdale, Arizona 85258 U.S.A. Fender knows the importance of sound reinforcement. From the simple box-top mixer to today's professional touring concert systems, the need to communicate, to make the connection between the performer and the audience is foremost in Fender's mind. Perhaps no other single piece of gear can make or break your band's sound. You see, your sound system is more than just a combination of di
ملخص المحتوى في الصفحة رقم 3
SRM 6302 / 8302 SRM 6302 / 8302 PROFESSIONAL POWERED PROFESSIONAL POWERED MIXER MIXER INTRODUCTION The SRM 6302 / 8302: a dual 150 watt professional 150 Watts per Channel at 4Ω ® powered mixer from your friends at Fender Pro Audio. We are sure you will find your new SRM Assignable Dual Power Amplifiers 6302 / 8302 to be both a unique and effective sound reinforcement product, providing years of 9-Band Assignable Graphic Equalizer trouble-free service. with 30mm Sliders With ease of setup in mi
ملخص المحتوى في الصفحة رقم 4
INPUT CHANNEL CONTROL FUNCTIONS PATCH BAY PANEL CONNECTIONS A. EFFECTS - This knob controls I KM the amount of signal its respective A channel sends to the overall effects mix. When the knob is set at 0, the MAX 0 output is “dry”. MAIN OUT MON OUT EFFECTS OUT/ EFFECTS FOOTSWITCH B. HIGH - Adjusts the amount of high frequency boost or cut in the J L N B channel. When all the tone controls are set at 0 (straight up), the 15 +15 channel is “flat” with no frequencies HIGH HIGH cut or boosted.
ملخص المحتوى في الصفحة رقم 5
MASTER CONTROL PANEL FUNCTIONS A. EQ ASSIGN - This button +12dB +12dB OFF C ON switches the graphic equalizer PHANTOM POWER MAIN between the main and the MON monitor bus. When this OdB OdB D A button is pressed, the EQ is POWER EQ ASSIGN assigned to the monitor bus. MAIN 12dB 12dB E MON 63 125 250 500 1k 2k 4k 8k 16k B. GRAPHIC EQUALIZER - PA 2 ASSIGN GRAPHIC EQUALIZER B This 9 band graphic equalizer consists of active band pass TAPE/ REVERB EFFECTS / band reject filters spaced at octave inte
ملخص المحتوى في الصفحة رقم 6
TAPE INPUT / OUTPUT JACKS O. TAPE IN - Unbalanced P. TAPE OUT - Unbalanced phono (RCA) output phono (RCA) input jacks jacks designed for use with a tape recorder. They L designed for use with a tape produce a mono signal. The rec out knob controls player, CD player, etc. These the tape out signal level. jacks sum the stereo left and R right input signal to a mono signal useful for playing IN OUT prerecorded music. The O P TAPE tape/effects return to main and tape/effects return to monitor c
ملخص المحتوى في الصفحة رقم 7
SPEAKER WIRING AND CONNECTIONS Parallel or series are the two basic ways which Additionally, power and audio signal cables are the multiple speakers can be connected to a single most common sources of sound system failure. power amplifier. When speakers are connected in Well made and carefully maintained cables are parallel, their combined impedance decreases. For essential to the reliability of the entire sound system. speakers wired in series the opposite is true, their If long speaker cable
ملخص المحتوى في الصفحة رقم 8
INPUT / OUTPUT CONNECTIONS BASIC SETUP OF YOUR SRM 6302 / 8302 The SRM 6302 / 8302 has a variety of Before using the SRM 6302 / 8302, connectors on its input / output panels. please read and follow the steps listed Below is a chart listing the various types below: and their pin outs. 1. IMPORTANT Heed all safety warnings when Jack Style Connection Pin Out operating the SRM 6302 / 8302. MIC XLR Balanced Pin 1 = GND INPUTS Female Input Pin 2 = POS 2. Make sure the power switch is in the OFF positi
ملخص المحتوى في الصفحة رقم 9
GROUNDING AND HUMS TROUBLESHOOTING Ground loops are one of the most If the SRM 6302 / 8302 is set up but common causes of hum and buzz in does not function, please check the sound reinforcement systems and other following items: audio products. A ground loop usually occurs if the separate pieces of equipment are plugged into different AC circuits. Also, if the audio wiring is placed too close to the power cords, hums or buzzes can bleed into • Is the SRM 6302 / 8302's power cord properly the
ملخص المحتوى في الصفحة رقم 10
SIMPLE SRM SETUP WITH MONITORS 3. The level control in each channel strip adjusts the amount of signal sent to the main bus where all channel signals are summed. The Main control in the master section adjusts the volume level to the 1. Connect a microphone to a Mic input jack and any main speakers. The Monitor control in each keyboard or other instrument to a Line input jack. channel strip adjusts the amount of signal sent to the monitor bus where all monitor channel signals 2. Next, connect
ملخص المحتوى في الصفحة رقم 11
RUNNING AN EFFECTS PROCESSOR THRU YOUR SRM 6302 / 8302 1. Connect speakers, microphones and other 3. The Effects control in each channel strip adjusts equipment to the SRM 6302 / 8302 as before. the amount of signal sent to the reverb / effects bus where all the effects signals from the channels are 2. Next, connect a cord from the Effects summed. The Effects control in the master section Out/Footswitch jack to the input of the effects adjusts the signal level to the effects processing unit p
ملخص المحتوى في الصفحة رقم 12
SRM WITH AN EXTERNAL MONITOR POWER AMP FOR MONITOR SPEAKERS 1. Connect a cord from the Mon Out jack to the monitor power amp and system. With an external monitor power amp, the SRM’s second power 2. The Monitor control in the master section adjusts amp may be assigned to the main bus for the signal level to the monitor power amp. additional power to the front of house speakers. When PA 2 is assigned to the main front of house 3. Be sure to turn the tape deck, keyboard or other enclosures, be sur
ملخص المحتوى في الصفحة رقم 13
SRM WITH AN EXTERNAL POWER AMP FOR FRONT OF HOUSE SPEAKERS 1. Connect a cord from the Main Out jack to an 2. The Main control in the master section adjusts external power amp. Be sure one monitor enclosure the signal level to your external power amp. is connected to a PA 1 Out jack and the other is connected to a PA 2 Out jack. (PA 1 power amp can 3. Be sure to turn your tape deck, keyboard or now be assigned to monitor speakers by connecting other instruments and gear on first, then your SRM
ملخص المحتوى في الصفحة رقم 14
SRM 6302 / 8302 SIGNAL FLOW DIAGRAM Typical signal path for each channel TO PHANTOM BUS LEVEL MIC TO MAIN BUS 21 CHANNEL EQ 3 HIGH TO EFFECTS/ INPUTS REVERB BUS MID LINE LOW EFFECTS TO MONITOR BUS MONITOR RETURN TO MONITOR TAPE / EFFECTS EFFECTS IN RETURN TO MAIN L TAPE IN R L TAPE REC OUT OUT R MAIN MAIN OUT PA 1 IN GRAPHIC EQ MONITOR PA 1 OUT PA 1 EQ ASSIGN PA 1 OUT PA 2 ASSIGN MON OUT PA 2 PA 2 OUT EFFECTS PA 2 OUT REVERB DELAY LINE PA 2 IN REVERB RETURN TO MONITOR EFFECTS OUT/ FOOTSWITCH REV
ملخص المحتوى في الصفحة رقم 15
SPECIFICATIONS FOR THE SRM 6302 DESIGNATION TYPE PR 332 PART NUMBER 071-6321-000 (120 V) THIS EQUIPMENT CONFORMS TO THE FOLLOWING DIRECTIVES : 071-6321-030 (240 V) Aust EMC 89/336/EEC AND LV 73/23/EEC 071-6321-040 (230 V) UK 071-6321-060 (230 V) Euro POWER SPECIFICATIONS 120V version: 120V AC, 60 Hz, 900W 230V version: 230V AC, 50 Hz, 900W 240V version: 240V AC, 50 Hz, 900W PRE-AMPLIFIER SECTION MIC INPUT IMPEDANCE 1.8 kΩ LINE INPUT IMPEDANCE 18.2 kΩ MIC INPUT SENSITIVITY 7 mV LINE INPUT
ملخص المحتوى في الصفحة رقم 16
SPECIFICATIONS FOR THE SRM 8302 DESIGNATION TYPE PR 332 THIS EQUIPMENT CONFORMS TO PART NUMBER 071-8321-000 (120 V) THE FOLLOWING DIRECTIVES : EMC 89/336/EEC AND LV 73/23/EEC 071-8321-030 (240 V) Aust 071-8321-040 (230 V) UK 071-8321-060 (230 V) Euro POWER SPECIFICATIONS 120V version: 120V AC, 60 Hz, 900W 230V version: 230V AC, 50 Hz, 900W 240V version: 240V AC, 50 Hz, 900W PRE-AMPLIFIER SECTION MIC INPUT IMPEDANCE 1.8 kΩ LINE INPUT IMPEDANCE 18.2 kΩ MIC INPUT SENSITIVITY 7 mV LINE INPUT
