ملخص المحتوى في الصفحة رقم 1
GILSJ JN MIXERS
CONCRETE MIXER MODEL 600CM
OPERATING INSTRUCTIONS & PARTS LIST
GILSJ JN MIXERS
4343 Easton Road · St. Joseph, MO 64503
BY
816-233-4840 · 800-253-3676
Fax 816-233-4624 · 888-253-3676
E-Mail: cleform@ccp.com
Web Address: www.cleform.com
ملخص المحتوى في الصفحة رقم 2
TO THE OWNER: This owner’s manual provides the information needed to operate and maintain this Gilson mixer. Carefully read and follow all safety and operating instructions in this manual. Also, be sure every operator of this mixer reads this manual before operating the mixer. The replacement of any part on this mixer by other than the manufacturer’s authorized replacement part may adversely affect the performance, durability or safety of the product. Be sure safety precautions are observed. Re
ملخص المحتوى في الصفحة رقم 3
Table of Contents 1. Warranty Information 3 2. Safety Instructions, Pre-operational Checks 4-5 3. Lubrication 5-6 4. Care of Mixer 6 5. Batch/Mix Instructions 6 6. Parts Explosions and Lists 7 HOW TO OBTAIN PARTS AND SERVICE INFORMATION For parts and service information,contact either your local dealer or the Cleform Tool Corp. factory: CLEFORM TOOL CORP. 4343 EASTON ROAD ST. JOSEPH, MO 64503 800-253-3676 PHONE 888-253-3676 FAX HOW TO ORDER PARTS When ordering parts be sure to indicate the follo
ملخص المحتوى في الصفحة رقم 4
WARRANTY: This mixer is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. Cleform Tool Corp. shall without charge, repair or replace parts which are found to be defective. All transportation charges for replacement parts must be bourne by the purchaser. For Warranty service, the product must be delivered, with proof of purchase date, to the dealer of original purchase, or any factory authorized service
ملخص المحتوى في الصفحة رقم 5
SAFETY INSTRUCTIONS SAFETY PRECAUTIONS: This is the industry’s safety alert symbol. This symbol calls attention to items or operations that could be dangerous. This symbol can be found throughout this manual and on safety decals on the mixer. Read these messages carefully. The following precautions are suggested to help prevent accidents. Read and practice the following precautions before operating this equipment. Equipment should be operated only by those who are responsible and have been
ملخص المحتوى في الصفحة رقم 6
TOWING & SAFETY CHAINS: For transporting the mixer, slide the tow pole out as far as possible and insert the locking pin. When operating the mixer, slide the tow pole in and lock it in place. Make sure drum is locked in position and engine housing is closed and secured. Cross the safety chains under the tow pole and fasten them to the tow vehicle. (fig.1) NOTE! Safety chain length may need to be altered for proper connection to tow vehicle. Reposition the hooks, DO NOT cut chain. Allow enough
ملخص المحتوى في الصفحة رقم 7
Drum Tilt Brake Bearing: The brake bearing casting is located near the front of the mixer and should be greased weekly. Handwheel Bearing: The handwheel hub bearing is located on the front of the mixer, behind the handwheel. This bearing should be greased weekly. WARNING: DO NOT GREASE BRAKE BAND OR OUTER BRAKING SURFACE OF TILT GEAR. Jack Shaft Bearings: Pillow block style bearings are used on the drive train counter shaft. These bearings should be greased weekly. Drive Chain: The drive chain
ملخص المحتوى في الصفحة رقم 8
7
ملخص المحتوى في الصفحة رقم 9
8
ملخص المحتوى في الصفحة رقم 10
9
ملخص المحتوى في الصفحة رقم 11
10
ملخص المحتوى في الصفحة رقم 12
11
ملخص المحتوى في الصفحة رقم 13
12
ملخص المحتوى في الصفحة رقم 14
13
ملخص المحتوى في الصفحة رقم 15
14
