ملخص المحتوى في الصفحة رقم 1
HP Wireless Rechargeable Optical Mouse
User’s Manual
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Product Number PP034AA #ABA
The information contained herein is subject to change without notice
Printed in China
The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable
ملخص المحتوى في الصفحة رقم 2
HEALTH WARNING There may be a risk of serious physical injuries from working at your computer workstation. Some studies have suggested that long periods of typing, improper workstation setup, incorrect work habits, stressful work conditions and relationships, or problems in your personal health may be linked to injuries. These injuries could include carpal tunnel syndrome, tendonitis, tenosynovitis, and other musculoskeletal disorders. The warning signs of these disorders can occur in
ملخص المحتوى في الصفحة رقم 3
Contents Welcome 4 Installation 5 Configuration 8 Troubleshooting 9 - 3 -
ملخص المحتوى في الصفحة رقم 4
Welcome Congratulations on purchasing the HP Wireless Rechargeable Optical Mouse. This guide will provide you with the necessary steps for installing and maintaining your mouse. Package Contents HP Wireless USB Receiver/Cradle AC Power CD with Rechargeable Optical Mouse Adapter Driver/Software 2 AA NiMH User’s Manual Warranty Card Rechargeable Batteries System Requirements • Available USB Port • CD-ROM Drive Compatible with Microsoft® Windows® 98SE/Me/2000/XP
ملخص المحتوى في الصفحة رقم 5
Installation CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Battery Installation STEP 1 - Remove the battery compartment cover located on the bottom of your mouse by pressing the tab forward. STEP 2 - Remove the plastic pull tab from the battery compartment. Close the battery compartment cover. STEP 3 - Place your mouse in the recharging cradle to charge. - 5 -
ملخص المحتوى في الصفحة رقم 6
Software Installation Insert the CD into your CD-ROM drive. If the setup program does not appear, click Start, then click Run. Type :\setup. Click OK. (For example, if the disk is in drive D, enter D:\Setup.) Follow the onscreen instructions. Hardware Installation STEP 1 - Power on your system. STEP 2 - Connect the USB receiver to any available USB port or hub connected to your computer. - 6 -
ملخص المحتوى في الصفحة رقم 7
User Setup Default mode By default your mouse is set into default mode which should allow your mouse to work right out of the box. If your mouse does not work, press and hold the button on the receiver until the green LED turns off. This will take approximately 4 seconds. Once the green LED begins blinking, your mouse should work. ID mode If you are using more than one mouse within 6 feet of the receiver, you must set both mice into ID Mode. Follow the instructions below to s
ملخص المحتوى في الصفحة رقم 8
Configuration You can configure the buttons of this mouse to perform selected functions… Windows XP – Category View Click Start, select Settings / Control Panel / Printers and Other Hardware / Mouse, to customize your mouse settings. Windows 98SE, Me, 2000 and XP – Classic View Click Start, select Settings / Control Panel / Mouse, to customize your mouse settings. You can also click the mouse icon located in your system tray to customize your mouse settings. When the softw
ملخص المحتوى في الصفحة رقم 9
Troubleshooting • If you have Windows 95 or Windows NT, these operating systems do not support this device. • The Universal Serial Bus Controller and USB root hub may not be properly installed on your system. Contact your computer manufacturer for details. Technical Support For technical assistance call 1-866-314-7239 or visit www.microinv.com/hp Technical Support hours of operation: Monday - Friday 8:30am to 10:00pm E.S.T. - 9 -
ملخص المحتوى في الصفحة رقم 10
FCC STATEMENT This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
ملخص المحتوى في الصفحة رقم 11
