ملخص المحتوى في الصفحة رقم 1
GB
System Keyboard
SSC-2000 User's Manual
F
D
ES
I
R
P
ملخص المحتوى في الصفحة رقم 2
9. Do not defeat the safety purpose of the polarized or GB-2 CAUTION grounding-type plus. RISK OF ELECTRIC A polarized plug has two blades with one wider than the SHOCK DO NOT OPEN other. A grounding type plug has two blades and a third CAUTION : TO REDUCE THE RISK OF ELECTRIC grounding prong. The wide blade or the third prong are SHOCK, DO NOT REMOVE COVER (OR provided for your safety. If the provided plug does not fit BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI- int
ملخص المحتوى في الصفحة رقم 3
ملخص المحتوى في الصفحة رقم 4
B. Camera movement key M. RS-485 - PRESET For RS-485 communication, it will be connected to the RS-485 termi- GB-4 - PATTERN nals of other system keyboards or controlling devices such as cam- - SCAN eras, DVR, and MUX. - AUTO PAN N. RS-232 C. Alarm release key Connection port to adjust the system key board in a factory. D. Joystick controller (UP/DOWN/LEFT/DOWN/AF/ZOOM) The Pan/Tilt connected with Samsung Dome Camera or Receiver Unit Chapter 2. Installation is moved to UP/DOWN/LEFT/RIGHT. Pre
ملخص المحتوى في الصفحة رقم 5
ملخص المحتوى في الصفحة رقم 6
• In case of connecting with Full Duplex - Connect with SSC-2000 by using the RS-485 port on the back of GB-6 - Connect the Txd (+) of Dome Camera RS-485 port with the Rx (+) of SHR-4080 SSC-2000. - Connect the Txd (-) of Dome Camera RS-485 port with the Rx (-) of • In case of connecting with Half Duplex SSC-2000. - Connect the Tx (+) of SHR-4080 RS-485 port with the Tx (+) of - Connect the Rxd (+) of Dome Camera RS-485 port with the Tx (+) of SSC-2000. SSC-2000. - Connect the Tx (-) of SHR-408
ملخص المحتوى في الصفحة رقم 7
ملخص المحتوى في الصفحة رقم 8
If the key board is not operated for three seconds, the graphic Chapter 4. Instructions panel is changed to the sleep mode and the screen is not dis- GB-8 played.(Blue Screen display) Press the touch panel/key or move the joystick/joy shuttle, and then the screen before the sleep mode is displayed again. Log-in 1. Turn on the power of all the components of the system. Camera control 2. When the power is applied by connecting the power adapter at the back of system keyboard, the following indica
ملخص المحتوى في الصفحة رقم 9
PATTERN movement PRESET DELETE GB-9 This function is to view the camera movement for 30 seconds desig- This function is to delete the preset position. nated by the user on the pattern mode of the camera menu. Press the pattern button on the keyboard, enter the pattern number(1~3) you 1. Press “DELETE”. want, and press “ENTER” to execute PATTERN movement. “PATTERN 1” will appear on the screen. • If there is any of MANUAL (PAN, TILT, ZOOM, FOCUS) input during auto execution (SCAN, AUTO PAN, PATT
ملخص المحتوى في الصفحة رقم 10
CAMERA connection information GB-10 Press the part marked as shown below to know the number of DVR and MUX that are con nected to the selected camera. English small letter input page will appear. Press “TEXT” if you want to enter large letters. A window will appear as shown below when you press the camera number display part. Press “NUMBER” if you want to enter numbers. Move to the connected device When you press “DVR 000” on the connection information screen, DVR 000 will be selected and the sc
ملخص المحتوى في الصفحة رقم 11
ملخص المحتوى في الصفحة رقم 12
ملخص المحتوى في الصفحة رقم 13
ADDRESS SET GB-13 RS-232 COMMUNICATION SETUP The address of the system keyboard can be set. Press “ADDRESS SET” and the keyboard address input window will appear as shown below. The default setup for the RS-232 communication of the keyboard is as follows. Enter the address by using the number keys and press the enter key. - BAUD RATE : 4800 Press enter the “EXIT” ICON on lower left if you want to clear the - DATA BIT : 8 window without entering the address. - PARITY CHECK : NONE - STOP BIT : 1 •
ملخص المحتوى في الصفحة رقم 14
PARITY CHECK Confirm New Password GB-14 The PARITY BIT of RS-232 communication can be set. This is to confirm the new password. Enter the password by using the Press “PARITY CHECK” and a pop-up window will appear as shown number keys (0~9) and press the enter key. If the entered number is below. not same as the New Password, an error message “Invalid Password!!” will be displayed on the screen. You have to start again from entering the operator’s number. CHECK PASSWORD Select one among None / Od
ملخص المحتوى في الصفحة رقم 15
DOWNLOAD process screen GB-15 A download process screen will appear as shown below when you press “OK” on the down load check screen. - Operator No. : Newly registered use's number - Password : New password is displayed.( ) ****** - Operator Level : The level of the new user can be set. A message will appear when downloading is completed. Operator Level Press “Operator Level” to set the level. CAMERA DATA UPLOAD You can choose one level among Admin. / Manager / Op
ملخص المحتوى في الصفحة رقم 16
UPLOAD progress screen Factory Default Setup GB-16 When you press “OK” on the UPLOAD check screen, UPLOAD Resets all of the menu values to the default value. progress screen will appear as shown below. Press “OK” to start the default setting. • The system will start again when the FACTORY DEFAULT ‘Complete’ message will appear when uploading is completed. SETUP is completed. Chapter 6. OPERATOR LEVEL There are 3 levels of user, who can be registered as a user, including Admin. / Manager / Operat
ملخص المحتوى في الصفحة رقم 17
Chapter 7. Product Specification Chapter 8. Q & A GB-17 ITEM DESCRIPTION The system keyboard communication is not worked. INTERFACE (RS-485) CONNECTOR TYPE : 4P TERMINAL TYPE - Check the RS-485 communication line. PORT : 1 PORT - Check the address setup of system keyboard. BAUD RATE : 4,800/9,600/19,200/38,400bps Refer to “RS-485 COMMUNICATION SETUP (GB-12)” of INTERFACE (RS-232C) CONNECTOR TYPE : D-SUB 9P PORT : 1 PORT “Chapter 5. Menu setting” for the method of address setup. BAUD RATE : 600/
ملخص المحتوى في الصفحة رقم 18
GB-18
