ملخص المحتوى في الصفحة رقم 1
FOODSER VICE
Owner’s Manual
Read And Save These Instructions
TM
T&G2
®
Blending Station
High Performance Commercial Blender
All Models
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS 1. Read all instructions. 2. To protect against risk of electrical shock, do not put motor base in water or other liquid. 3. Close adult supervision is necessary when appliance is used by or near children. 4. Unplug the power cord from the wall outlet when the T&G 2 ® Blending Station is not in use, before putting on or taking off parts, and before cleaning other than washing the container. 5. Never contact moving parts. 6. Do not operate any appliance with a damaged cord
ملخص المحتوى في الصفحة رقم 3
13. Always operate with the lid in place. 14. Display window area will scratch when contacted with a scouring pad or sharp object. Use a soft cloth to wipe the control panel area clean. ® 15. The T&G 2 Blending Station cannot be cleaned with a water jet. 16. Installation for a 120 VAC unit requires you to have at least one 20 amp outlet per machine, available within six feet of the T&G 2 Blending Station. 220 VAC and 100 VAC units require a dedicated line. Consult an electrician for proper elec
ملخص المحتوى في الصفحة رقم 4
pecifications S ® T&G 2 Blending Station On-Counter: Height of unit closed: 22” (54.56 cm) Shipping weight: 21 lbs. (9.534 kg) Dimensions: 22” High x 9-1/4” Wide x 10-1/2” Deep (54.56 cm x 23.45 cm x 25.86 cm) T&G 2 Blending Station In-Counter: Height of unit above counter: 17-1/2” (44.45 cm) closed Depth of unit below counter: 5-2/3” (13.3 cm) Shipping Weight: 18 lbs. (8.172 kg) Dimensions: 24” total height x 9” Width x 12-3/4” Depth (45.03 cm x 22.65 cm x 32.39 cm) NOTE: For In-Counter Inst
ملخص المحتوى في الصفحة رقم 5
ontrol Panel C Display Window Owner Controls Six Program Buttons High/Low Pulse ® T&G2 Blending Station ON/OFF switch - Located on the side of the motor base the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending. SIX PROGRAM buttons - These buttons, numbered 1 thru 6, are pre-programmed blending cycles designed for the most commonly made drinks. Depending on the viscosity of the drink you are creating, pressi
ملخص المحتوى في الصفحة رقم 6
ملخص المحتوى في الصفحة رقم 7
Cover with Removable Hinge Design Cover Door: 1. The Cover Door can be removed by opening it until the door is horizontal. Then, gently spread the sides of the door over the round hinges and remove. 2. To reinstall the Cover Door, gently spread the sides of the door and place the door hinge cutouts over the round hinges. (Figure C) Back Cover: 1. To remove the Back Cover from the Blending Station: a. First remove the Cover Door from the unit, as described above. b. Remove the two (2) Back Cover
ملخص المحتوى في الصفحة رقم 8
n-Counter Installation I Preparing the counter area: • Before cutting holes, make sure that there is adequate clearance under the counter for the motor. The motor will extend about 5-2/3" (14.4 cm) below the counter but it is best to allow at least 10" (25.5 cm) from the under-counter to shelves or any other equipment under the counter. Also, when using the removable cover design, the back of the hole must be at least 6” (15.2 cm) from any wall to allow for cover door clearance. • An extra 6.5”
ملخص المحتوى في الصفحة رقم 9
® In-Counter T&G 2 Blending Station dimensions: • 17-1/2” (44.45 cm) high with lid closed • 21-1/2” (54.7 cm) high with lid open • Case depth: 12-3/4” (32.39 cm) with handle • Case width: 9-1/2” (24.13 cm) • Depth below counter: 5-2/3” (14.4 cm) • Recommended distance between machines: 12” (30.48 cm) from the edge of each machine or as far apart as possible. 21-1/2” (54.7 cm) 6” (15.2 cm) 12-3/4” (32.39 cm) 12” (30.48 cm) 12” (30.48 cm) IN-COUNTER HOLE Additional Unit Additional Unit Cut 7-1/2”
ملخص المحتوى في الصفحة رقم 10
n-Counter Gasket I Gasket Installation Instructions: 1. Follow the instructions on page 8 on preparing the counter area for the installation of ® your In-Counter T&G 2 Blending Station. Also, use the Template Sheet (provided in your machine’s original package) to assist you in the placement and ventilation of your machine. 2. Lay the blender on its back with the motor pointing toward you. Allow 1-2 in. (2.54 -5.08 cm) of the motor base to hang over the edge of the counter top to facilitate ea
ملخص المحتوى في الصفحة رقم 11
ملخص المحتوى في الصفحة رقم 12
nstructions I ® How to operate your T&G 2 Blending Station using the six Programmed Buttons. The following is the basic factory settings of the six PROGRAMMED buttons: • Press Button One for program - SMOOTHIE - Blends drinks with just juice and ice. • Press Button Two for program - SMOOTH 2 - Blends regular smoothies for an extended cycle. • Press Button Three for program - COFFEE - Blends light coffee drinks. • Press Button Four for program - SHAKES -This cycle is good for ice cream and milksh
ملخص المحتوى في الصفحة رقم 13
7. When the cycle is complete the blender stops. Wait until blade comes to a complete stop before removing the lid and/or container from the motor base. 8. Remove the container, pour, garnish and serve the drink. NOTE: On all units the built-in thermal sensor keeps track of how hot the motor gets and will warn the user and eventually shut down the motor if the motor is overheating. When overheated the display will instruct the user to remove the container and run the machine until cool. This t
ملخص المحتوى في الصفحة رقم 14
arts List P Item# Part #15573 32 oz. (900 ml) - XP Container without lid assembly or blade assembly #15571 32 oz. (900 ml) - XP Container, blade assembly, no lid assembly #1159 32 oz. (900 ml) - Lid plug #15570 32 oz. (900 ml)- XP Container, blade assembly & lid assembly #15574 32 oz. (900 ml) - 2-piece lid assembly for XP Container #15575 32 oz. (900 ml) - Lid only (no plug) for XP Container #18002 Back cover and cover door with removable hinge design #18003 Cover door with removable hinge de
ملخص المحتوى في الصفحة رقم 15
ملخص المحتوى في الصفحة رقم 16
are and Cleaning C Care Note To ensure that you get the longest possible life from your Vita-Mix product, we recommend the following products, when used as directed by the supplier: Cleaning Product ..........................................................................Supplier Solid Supra, Solid Power, ..............................................................Ecolab, Inc., St. Paul, MN Guardian Acclaim, Solid Guardian Plus, ........................................Tel: (800) 352-5326 Soli
ملخص المحتوى في الصفحة رقم 17
Motor Base 1. Unplug the power cord. 2. Wash outside surface with a damp soft cloth or sponge, which has been rinsed in a mild solution ® of liquid dish soap (Ivory Liquid or equivalent) in warm water. NEVER IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID. NEVER POUR WATER OR ANY OTHER LIQUID ON THE MOTOR BASE. 3. Polish with a soft cloth. Control Panel Gently wash the front panel with a soft cloth and a low pH balanced soap, being careful not to scratch the Display Window. NOTE: Be sure to wring ex
ملخص المحتوى في الصفحة رقم 18
roubleshooting T Top nine problems you can fix on your own: 1. Problem: Solution #1: • Display Panel reads Turn the machine off and on again to reset the programming. THERMAL SENSOR FAILURE Solution #2: Call Vita-Mix Customer Service.* 2. Problem: Solution #1: • Loud noise from blender container Broken or worn Drive Socket. Replace (Item blade area # 891). Instructions are included with part. • Container blades do not spin Solution #2: • Increased vibration Check blade assembly for loose, damage
ملخص المحتوى في الصفحة رقم 19
7. Problem: Solution #1: • Machine is running irregular Turn the machine off and on again to reset • “NO PROGRAM” is displayed when a the programming. button is pushed Solution #2 • Button pressed starts the wrong Reset the machine to its original factory program settings. (Follow the instructions on page 7) • Machine starts by itself Solution #3: • A specific program button is defective Try plugging the machine into a new outlet. • Machine was turned off for a day, Solution #4: week or month a
ملخص المحتوى في الصفحة رقم 20
lade Agitator Assembly B Blade Agitator Assembly. Use caution when handling the blade; it is sharp. When inserting the blade assembly through the container bottom, grip the blades with a soft cloth, align the flat sides of the blade assembly with the flat sides of the container. Place the retainer nut 32 back on the inserted blade assembly and tighten clockwise. Do not 24 force. Do not attempt to disassemble blade assembly. 16 Drive Spline. Mates with drive socket on the motor base to turn th
