ملخص المحتوى في الصفحة رقم 1
Quick Installation Guide
TEW-434APB
ملخص المحتوى في الصفحة رقم 2
Table of Contents Table of Contents English ...................................................................................................... 1 1. Before You Start ................................................................................. 1 2. Hardware Installation ......................................................................... 2 3. Power-over-Ethernet Installation ...................................................... 3 4. Configure the Access Point ..............
ملخص المحتوى في الصفحة رقم 3
1. Before You Start Package Contents TEW-434APB Quick Installation Guide User’s Guide CD-ROM AC Power Adapter (7.5V 1A) 1 x 2dBi Detachable Antenna Installation Requirements Web Browser: Internet Explorer (5.5 or higher) A computer with a network adapter properly installed A network Switch or Hub with an available network LAN port A RJ-45 network cable Power over Ethernet Switch (Optional) TPE-101I (Optional) Application 54Mbps 802.11g Wireless PoE Access Point (TEW-434ABP) Workstation with
ملخص المحتوى في الصفحة رقم 4
2. Hardware Installation Note: Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network. Please connect the computer configuring the TEW-434APB to the same switch/hub. 1. Connect a RJ-45 cable from the Switch/Hub to the LAN port of the Access Point and then connect the 2dBi Detachable Antenna. 2. Connect the Power Adapter to the Access Point and then to a power outl
ملخص المحتوى في الصفحة رقم 5
3. Power-over-Ethernet Installation Using the TEW-434APB with a PoE switch 1. Connect a RJ-45 cable from the Power-over-Ethernet Switch (e.g. TRENDnet TPE-S88) to the LAN port of the Access Point and then connect the 2dBi Detachable Antenna. 2. Verify that the following panel lights are on: WLAN and LAN. Please refer to step 3 in the Hardware Installation section. 3 English
ملخص المحتوى في الصفحة رقم 6
Using the TEW-434APB with the TPE-101I 1. Connect the Power Cord to the AC Power Adapter. 2. Connect the AC Power Adapter to the DC 48V IN connector on the TPE-101I. Then connect the Power Cord to an outlet. 3. Connect a CAT-5 cable from a switch to the TPE-101I's DATA IN port. 4. Connect a CAT-5 cable from the TEW-434APB's LAN port to the TPE-101I's POE OUT port 5. Verify that the following panel lights are on: WLAN and LAN. Please refer to step 3 in the Hardware Installation. 4 E
ملخص المحتوى في الصفحة رقم 7
4. Configure the Access Point Note: It is recommended that you configure the Access Point from a wired computer. Before the Access Point can be configured, a Static IP address must be assigned to your computer's network adapter in the subnet of 192.168.1.x. Since the Access Point's default IP address is 192.168.1.100, make sure no other network devices are assigned an IP address of 192.168.1.100. (Refer to the Troubleshooting section on how to configure TCP/IP settings on your PC) 1.
ملخص المحتوى في الصفحة رقم 8
4. Click Next. 5. Enter a new password for your Access Point, verify the new password, and then click Next. (If a new password is not entered, the default password admin will be used. 6. Enter a SSID for your Access Point and then click Next. 6 English
ملخص المحتوى في الصفحة رقم 9
7. Enable Encryption if needed and then click Next. 8. Click Restart. 9. Click Close. Your installation is now complete. For detailed information regarding the TEW-434APB's configuration and advanced settings, please refer to the Troubleshooting section, User's Guide CD-ROM, or TRENDnet's website at http://www.trendnet.com. 7 English
ملخص المحتوى في الصفحة رقم 10
Troubleshooting Q1: How do I configure TCP/IP settings on my computer? 1. Go into the Control Panel and double- click the Network Connections icon, right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Use the following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.1.x. Q2: I typed http://192.168.1.100 in my Internet Browser's Address Bar,
ملخص المحتوى في الصفحة رقم 11
Q4: After I successfully configured the Access Point to match my network settings, I can not connect to my network using wireless computers. A4: If you have a DHCP server in your network, you need to go into TCP/IP settings again and re-select "Obtain an IP address automatically" to allow the PC to regain an IP address from your DHCP server. Q5: All the settings are correct, but I can not make a wireless connection to the Access Point. A5: First, double check that the WLAN light on the Acces
ملخص المحتوى في الصفحة رقم 12
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling
ملخص المحتوى في الصفحة رقم 13
TRENDnet Technical Support . US Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support . . . . . Europe (Germany France Italy Spain Switzerland UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDn
