ملخص المحتوى في الصفحة رقم 1
®
EZ-ZONE PM
User’s Manual
Integrated Controller Models
TOTAL
CUS CUST TO OM MER ER
S SA ATISF TISFA AC CTI TIO ON N
3 Year Warranty
ISO 9001 ISO 9001
Registered Company
Winona, Minnesota USA
1241 Bundy Boulevard., Winona, Minnesota USA 55987
Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com
0600-0059-0000 Rev. C Made in the U.S.A.
March 2008 $15.00
ملخص المحتوى في الصفحة رقم 2
• Complete model number Safety Information • All configuration information We use note, caution and warning symbols through- out this book to draw your attention to important • User’s Manual operational and safety information. • Factory Page A “NOTE” marks a short message to alert you to an important detail. Return Material Authorization (RMA) A “CAUTION” safety alert appears with informa- 1. Call Watlow Customer Service, (507) 454-5300, tion that is important for protecting your equip- for
ملخص المحتوى في الصفحة رقم 3
TC Table of Contents Chapter 1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Standard Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2: Install and Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Chapter 3: Keys and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Attention Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ملخص المحتوى في الصفحة رقم 4
1 Chapter 1: Overview ® The EZ-ZONE PM takes the pain out of solving A gency approvals: UL Listed, CSA, CE, RoHS, your thermal loop requirements. W.E.E.E. FM ® Watlow’s EZ-ZONE PM controllers offer options • Assures prompt product acceptance to reduce system complexity and the cost of control- • Reduces end product documentation costs ® loop ownership. You can order the EZ-ZONE PM as • FM approval on Limit Models a PID controller or an over-under limit controller, or you can combine both fun
ملخص المحتوى في الصفحة رقم 5
Keep in mind that a function is a user-pro- A Conceptual View of the PM grammed internal process that does not execute any The flexibility of the PM’s software and hardware al- action outside of the controller. To have any effect lows a large range of configurations. Acquiring a bet- outside of the controller, an output must be config- ter understanding of the controller’s overall function- ured to respond to a function. ality and capabilities while at the same time plan- ning out how the cont
ملخص المحتوى في الصفحة رقم 6
® EZ-ZONE PM Integrated Model 1/16 DIN with a Current Transformer — Input/Output (no communications options 2 to 3) Universal Sensor Input, Configuration Communications, Red/Green 7-Segment Display Input Output Functions Functions PID Output 1 none, switched dc/open off, heat, cool, Controller collector, form C mechanical (5 A) or duplex, alarm, Analog Input 1 thermocouple, Board solid-state (0.5 A) relay, process (V, mA) input sensor retransmit, RTD, process (V, mV, mA, 1k
ملخص المحتوى في الصفحة رقم 7
® EZ-ZONE PM Integrated Model 1/16 DIN with Remote Set Point — Input/Output (no communications options 2 to 3) Universal Sensor Input, Configuration Communications, Red/Green 7-Segment Display Output Input Functions Functions PID Output 1 none, switched dc/open off, heat, cool, Controller collector, form C mechanical (5 A) or duplex, alarm, Analog Input 1 thermocouple, Board solid-state (0.5 A) relay, process (V, mA) retransmit, input sensor RTD, process (V, mV, mA, 1k po- Slo
ملخص المحتوى في الصفحة رقم 8
® EZ-ZONE PM Integrated Model 1/16 DIN with a Limit — Input/Output (no communications options 2 to 3) Universal Sensor Input, Configuration Communications, Red/Green 7-Segment Display Output Input Functions Functions PID Output 1 none, switched dc/open off, heat, cool, Controller collector, form C mechanical (5 A) or duplex, alarm, Analog Input 1 thermocouple, Board solid-state (0.5 A) relay, process (V, mA) retransmit, input sensor RTD, process (V, mV, mA, 1k po- Slot A even
ملخص المحتوى في الصفحة رقم 9
® EZ-ZONE PM Integrated Model 1/16 DIN with Expanded Communications — Input/Output Universal Sensor Input, Configuration Communications, Red/Green 7-Segment Display Input Output Functions Functions PID Output 1 none, switched dc/open off, heat, cool, Controller collector, form C mechanical (5 A) or duplex, alarm, Analog Input 1 thermocouple, Board solid-state (0.5 A) relay, process (V, mA) input sensor retransmit, RTD, process (V, mV, mA, 1k po- Slot A event tentiometer)
ملخص المحتوى في الصفحة رقم 10
Chapter 2: 2 Install and Wire Dimensions 15.8 mm (0.62 in) 101.6 mm 53.3 mm (4.00 in) (2.10 in) 53.3 mm (2.10 in) Side Front L1 L3 98 K1 99 K3 J1 J3 CF 51.2 mm L2 CD L4 (2.02 in) K2 K4 CE T1 B5 T2 S1 S2 D6 R1 D5 R2 Top Back 45.2 mm (1.78 in) Recommended panel spacing 45.2 mm (1.78 in) panel thickness 1.53 to 9.52 mm (0.060 to 0.375) 21.6 mm (0.85 in) 21.6 mm (0.85 in) ® Watlow EZ-ZONE PM Integrated Controller • 8 • Chapter 2 Install and Wire
ملخص المحتوى في الصفحة رقم 11
The tabs on each side of the mounting collar have Installation teeth that latch into the ridges on the sides of the panel controller. Each tooth is staggered at a different bezel retention collar depth from the front so that only one of the tabs, on each side, is locked onto the ridges at a time. gasket Note: There is a graduated measurement difference between case the upper and lower half of the display to the panel. In order to meet the seal requirements mentioned above, ensure that the
ملخص المحتوى في الصفحة رقم 12
Returning the Controller to its Case 1. Ensure that the orientation of the controller is correct and slide it back into the housing. Note: The controller is keyed so if it feels that it will not slide back in do not force it. Check the orientation again and reinsert after correcting. 2. Using your thumbs push on either side of the con- troller until both latches click. Chemical Compatibility This product is compatible with acids, weak alkalis, alcohols, gamma radiation and ultraviolet radia
ملخص المحتوى في الصفحة رقم 13
Communications Output 3 Output 4 Input 2 Output 1 Output 2 Input 1 Slot A Slot B Output Terminal Function Configuration 1234 X1 X3 common (Any switched dc output can use this common.) Switched dc/open collector W1 W3 dc- (open collector) output 1: PM6 _ _ C _-_ _ _ _ A _ _ Y1 Y3 dc+ output 3: PM6 _ _ _ _-_ _ C _ A _ _ W2 W4 dc- Switched dc Y2 Y4 dc+ output 2: PM6 _ _ _ C-_ _ _ _ A _ _ output 4: PM6 _ _ _ _-_ _ _ C A _ _ F1 F3 voltage or current - Universal Process G1 G3 voltage + output 1: PM6 _
ملخص المحتوى في الصفحة رقم 14
Communications Output 3 Output 4 Input 2 Output 1 Output 2 Input 1 Slot C Terminal Function Configuration 98 power input: ac or dc+ all 99 power input: ac or dc- CC Standard Bus or Modbus RTU EIA-485 common Standard Bus or Modbus CA Standard Bus or Modbus RTU EIA-485 T-/R- PM6 _ _ _ _-1 _ _ _ A _ _ CB Standard Bus or Modbus RTU EIA-485 T+/R+ CF Standard Bus EIA-485 common PM6 _ _ _ _-(A, 2 or 3) _ _ _ A _ _ CD Standard Bus EIA-485 T-/R- CE Standard Bus EIA-485 T+/R+ B5 digital input-output commo
ملخص المحتوى في الصفحة رقم 15
Low Power Ó Slot C power 98 Warning: fuse power Use National Electric (NEC) 99 • 12 to 40VÎ (dc) or other country-specific CF • 20 to 28VÅ (ac) standard wiring and safety • 20 to 28VÅ (ac) Semi Sig F47 CD practices when wiring and • 47 to 63 Hz CE connecting this controller to • 10VA maximum power consumption B5 PM6 _ (3 or 4) _ _-_ _ _ _ A _ _ a power source and to elec- trical sensors or peripheral D6 devices. Failure to do so may D5 result in damage to equip- ment and property, and/or
ملخص المحتوى في الصفحة رقم 16
Input 1 Thermocouple Ó Slot A L1 Warning: • 20 Ω maximum source resistance Use National Electric (NEC) K1 • >20 MΩ input impedance or other country-specific J1 • 3 microampere open-sensor detection standard wiring and safety L2 • Thermocouples are polarity sensitive. The negative lead (usually practices when wiring and red) must be connected to S1. K2 connecting this controller to • To reduce errors, the extension wire for thermocouples must be T1 of the same alloy as the thermocouple. a
ملخص المحتوى في الصفحة رقم 17
Input 2 Thermocouple Ó Slot B L3 Warning: • 20 Ω maximum source resistance Use National Electric (NEC) K3 • >20 MΩ input impedance or other country-specific J3 • 3 microampere open-sensor detection standard wiring and safety L4 • Thermocouples are polarity sensitive. The negative lead (usually practices when wiring and red) must be connected to S2. K4 connecting this controller to • To reduce errors, the extension wire for thermocouples must be T2 a power source and to elec- of the same
ملخص المحتوى في الصفحة رقم 18
Input 2 Current Transformer Ó Slot B L3 Warning: Use National Electric (NEC) K3 • Input range is 0 to 50 mA. or other country-specific J3 • current transformer part number: 16-0246 standard wiring and safety • 100 Ω input impedance L4 practices when wiring and • response time: 1 second maximum K4 • accuracy +/-1 mA typical connecting this controller to T2 PM6 _ _ _ _-_ T _ _ A _ _ a power source and to elec- trical sensors or peripheral S2 devices. Failure to do so may R2 result in damage t
ملخص المحتوى في الصفحة رقم 19
Output 1 Switched DC/Open Collector Ó Switched DC Slot A • 30 mA dc maximum supply common X1 Warning: current dc - (open collector) Use National Electric (NEC) • short circuit limited to <50 mA W1 Switched DC dc + • 22 to 32VÎ (dc) open circuit or other country-specific Y1 voltage standard wiring and safety dc- - L2 • Use dc- and dc+ to drive exter- W1 Load practices when wiring and dc+ nal solid-state relay. + K2 Y1 connecting this controller to • DIN-A-MITE compatible Internal T1 a p
ملخص المحتوى في الصفحة رقم 20
Output 1 Solid-state Relay, Form A Ó Slot A normally open • 0.5 A at 20 to 264VÅ (ac) maxi- L1 Warning: mum resistive load common K1 Use National Electric (NEC) • 20 VA 120/240VÅ (ac) pilot duty Solid-state Relay • opto-isolated, without contact or other country-specific normally suppression L1 standard wiring and safety open L2 • maximum off state leakage of K1 practices when wiring and common 105 microamperes K2 Internal Circuitry connecting this controller to • output does not supply p
