Abocom AR1000 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

ADSL ROUTER
Quick Installation Guide
M73-APO07-110

ملخص المحتوى في الصفحة رقم 2

Parts Names and functions Rear view of the ADSL ROUTER LED Indicator Top View of ADSL ROUTER (LEDs) - 1 -

ملخص المحتوى في الصفحة رقم 3

Description LED POWER Router Power on/off Indicator ADSL_PWR ADSL Module Power on/off Indicator ETH_LNK Ethernet Link Indicator ETH_ACT Ethernet Active Indicator ADSL_AUTO ADSL Auto Connection Indicator ADSL_LINK ADSL Data Link Indicator ADSL_ERR ADSL Link Error Indicator Connectors on the Rear Panel The following table describes the function of the connectors and switches on the ADSL ROUTER rear panel. See the following illustration for the location of the connectors described in the followin

ملخص المحتوى في الصفحة رقم 4

Setting Up the Hardware Environment Connecting All Cables to the Network Perform the following procedures to set up the ADSL ROUTER. Step 1 Connect the power adapter to the port labeled 5VDC on the rear panel of this device. Step 2 Connect the Ethernet cable. One PC – ADSL Router (direct connection) If your only have one PC, you can connect your ADSL ROUTER to the PC directly without a hub. For a single Ethernet-equipped PC, use the "non-hub" twisted-pair crossover cable to connect the ADSL ROUT

ملخص المحتوى في الصفحة رقم 5

Step 4 Connect one end of RS-232 cable to any free COM port in your system; Connect the other end to “Console” port on the rear panel of the ADSL router. Powering On the ADSL ROUTER Step 1 Connect the power adapter to your ADSL ROUTER by plugging one end of the power supply into an appropriate electrical outlet and the other end into port labeled on the rear panel of the device. 5VDC Note: To power off he ADSL ROUTER, just unplug the power supply cable from the ADSL ROUTER rear panel POWER conn

ملخص المحتوى في الصفحة رقم 6

INTERNET ACCESS Router Mode/ IP over ATM (RFC1577) (1) Run the “router.exe” file saved in the configuration utility. (Go to Start Program ADSL Router xx Configuration Utility Configuration Utility.) (2) Select a PC COM port available on your computer used to connect to the ADSL Router’s “Console” port. (3) Check “Router Protocol” and select “IP over ATM”. (4) Click “Properties” button. (5) Enter “ADSL IP”, “Gateway IP”, and “Subnet Mask” addresses provided by your service provider. (6) Usuall

ملخص المحتوى في الصفحة رقم 7

(8) Click “ ” to go to “ ” menu. Or click “ ” to save the settings OK Select Config Save As File for future use. Then click “ ”. Next (9) Click “ ” button. The configure utility will automatically setup the router for Configure you. Expect a minor delay for configuration. Bridge mode/RFC1483 bridge (1) Run the “router.exe” file saved in the configuration utility. (Go to Start Program ADSL Router xx Configuration Utility Configuration Utility.) (2) Select a PC COM port available on your compu

ملخص المحتوى في الصفحة رقم 8

(6) Enter VPI and VCI numbers. Then click “OK”. (7) Check “LLC Encapsulation” or “VC Based Route” or “VC Based Bridge”. (8) Click “Next” followed by “Configure”. Configure utility will automatically setup the router for you. Expect a minor delay for the router configuration. (9) Click “Finish”. Now you have finished ADSL Router configuration. The ADSL Router will handshake with ADSL central site equipment (DSLAM) and try to make the ADSL connection. - 7 -