Billion Electric Company BiPAC 5200S Series دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

BiPAC 5200 Series
(802.11g) ADSL2+ Firewall Router




Quick Start Guide

ملخص المحتوى في الصفحة رقم 2

Billion BiPAC 5200 Series ADSL2+ Firewall Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE USER’S MANUAL ON THE CD-ROM. Package Contents BiPAC 5200 Series ADSL2+ Router CD containing the on-line manual RJ-11 ADSL/telephone cable Ethernet (CA

ملخص المحتوى في الصفحة رقم 3

Quick Start Guide Hardware Overview BiPAC 5200G/ 5200GR2/ 5200GR3/ 5200GR4/ 5200GR5 The Front LEDs Lit when successfully Lit green when the connected to an ADSL Lit when power is ON wireless connection DSLAM connection. is established Lit when the Lit when connected to Lit steady when there system is ready an Ethernet device is a PPPoA / PPPoE connection The Rear Ports Connect your Connect the supplied computer to a LAN Connect the power adapter to

ملخص المحتوى في الصفحة رقم 4

Billion BiPAC 5200 Series ADSL2+ Firewall Router BiPAC 5200/ 5200R3 The Front LEDs Lit steady when Lit when connected there is a PPPoA to an Ethernet Lit when power is ON / PPPoE device Lit when the Lit when successfully system is ready connected to an ADSL DSLAM connection. The Rear Ports Connect the Connect your supplied power computer to a LAN adapter to this port, using the jack included Ethernet cable

ملخص المحتوى في الصفحة رقم 5

Quick Start Guide BiPAC 5200S/ 5200SR2/ 5200SR3 The Front LEDs Lit when Lit when Lit steady when connected to an there is a PPPoA power is ON Ethernet device / PPPoE Lit when successfully Lit when the connected to an ADSL system is ready DSLAM connection. The Rear Ports Attention: BiPAC 5200S has not supported the ON/OFF switch Connect your Connect the computer to a LAN supplied power port, using the adapter to this included Ethernet jack cable

ملخص المحتوى في الصفحة رقم 6

Billion BiPAC 5200 Series ADSL2+ Firewall Router Hardware Connection BiPAC 5200G/ 5200GR2/ 5200GR3/ 5200GR4/ 5200GR5 BiPAC 5200/ 5200R3 BiPAC 5200S/ 5200SR2/ 5200SR3 5

ملخص المحتوى في الصفحة رقم 7

Quick Start Guide Hardware Installation 1. Power Connection Plug the supplied power adapter to the wall jack and the other side to the router. Please note that the plug type may differ according to different countries. 2. LAN Connection Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC’s Ethernet interface. 3. ADSL Connection Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other side to the phone

ملخص المحتوى في الصفحة رقم 8

Billion BiPAC 5200 Series ADSL2+ Firewall Router 4. Splitter/ Micro-filter Connection Splitter / Micro-filter are important for ADSL installation. High-frequency signals are directed to the ADSL modem, and low-frequency signals are directed to the telephone or other analog voice-channel device to prevent inter-modulation distortion and also to get good speed and stable ADSL sync rate. a) Splitter connection If the installation has only a single telepho

ملخص المحتوى في الصفحة رقم 9

Quick Start Guide Troubleshooting 1. None of the LEDs are on when you turn on the router. Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support. 2. You have forgotten your router login and/or password. Try the default login and password, please refer to Chapter 3. If this fails, you can restore your router to its factory settings by holding the Reset button on the back of your ro