ملخص المحتوى في الصفحة رقم 1
LINEAR
BIASI B/40 PAGE 1
6-12 SECTION
Please Read Instructions Carefully
Save for Future Reference
WARNING
If the information in this manual is not followed
exactly, a fire explosion may result causing property
damage, personal injury or loss of life.
DANGER
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance
• Do not touch any electric switch; do not use any
phone in your building
• Immediately call your gas supplier from another
location. Follow the gas supplier
ملخص المحتوى في الصفحة رقم 2
PAGE 2 BIASI B/40 Dear Customer: Thank you for buying a Linear commercial boiler. The Linear is a cast iron, oil or gas fired hot water boiler, using the famous 3-pass design. The boiler is simple, rugged and engineered for maximum heating efficiency. We realize that it is not possible to answer all questions about the Linear series boiler in this manual. Reading this installation manual does not make the reader an expert in all aspects of installation and operation, and does not
ملخص المحتوى في الصفحة رقم 3
BIASI B/40 PAGE 3 TABLE OF CONTENTS BIASI B-40 Linear Series Section Page Important Information 1 4 General Information 2 6 Codes and Regulations 3 6 Combustion Air Supply 4 7 Boiler Location 5 7 Boiler Block Assembly 6 8 Boiler Trim Kit Installation 7 8 Boiler Tapping Diagram - 9 Burner Set-up 8 10 Gas Piping 9 12 Breeching and Chimney 10 14 Piping 1
ملخص المحتوى في الصفحة رقم 4
PAGE 4 BIASI B/40 IMPORTANT INFORMATION Please read this page carefully. ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL PLUMBING, HEATING AND ELECTRICAL CODES AND ORDINANCES, AS WELL AS THE REGULATIONS OF THE SERVING ELECTRICAL, WATER AND GAS UTILITIES. All systems should be designed by competent contractors, and only persons knowledgeable in the layout and installation of heating systems should attempt the installation of any boiler. It is the respons
ملخص المحتوى في الصفحة رقم 5
BIASI B/40 PAGE 5 WARNING Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon monoxide (CO). Carbon Monoxide (CO) is a gas which is odorless, colorless and tasteless but is very toxic. If your BIASI B-40 boiler is not working properly, or is not vented properly, dangerous levels of CO may accumulate. CO is lighter than air and thus may travel throughout the building. BRIEF EXPOSURE TO HIGH CONCENTRATIONS OF CO, OR PROLONGED EXPO
ملخص المحتوى في الصفحة رقم 6
PAGE 6 BIASI B/40 2. General Information: The Linear series are wet base design, sectional, cast-iron boilers for forced hot water heating systems. The Linear boilers are designed for firing with oil and deliver high efficiencies through unique design and construction. The Linear series boilers are shipped from the factory in assembled blocks and each boiler can range from 6 to 12 sections. The sections can then be disassembled before delivery to the jobsite by QHT and then field asse
ملخص المحتوى في الصفحة رقم 7
BIASI B/40 PAGE 7 4. Combustion Air Supply: The boiler location must provide air for proper combustion and ventilation of the surrounding area. To burn efficiently, oil requires 30 CFM/GAL. In general, boiler rooms should incorporate two (2) permanent air supply openings, one commencing within 12 inches of the ceiling, and one commencing within 12 inches of the floor. These openings should freely communicate with the outdoors. OUTSIDE AIR: When combustion air is supplied directly t
ملخص المحتوى في الصفحة رقم 8
PAGE 8 BIASI B/40 6. Boiler Block Assembly: All Linear series boilers are shipped either as an assembled boiler block or a knock-down boiler block. If the block came unassembled, or if the assembled block needs to be split for installa- tion purposes, please read the following: To assemble split blocks, move the sections into a line facing each other. Sections may be slid along boards placed underneath the sections. Inspect nipple ports for damage or burrs. Remove any burrs by bru
ملخص المحتوى في الصفحة رقم 9
BIASI B/40 PAGE 9 Control Panel with 2.5” MPT Supply operating aquastats 8” Breech 2.5” MPT Return Figure 1:Diagram illustrating the location and function of the front and rear boiler tappings. Boiler Model Length (L) B-40/6 34.8” B-40/7 39.5” B-40/8 44.5" B-40/9 49.2" B-4/10 53.9" B-4/11 58.8" B-4/12 63.9"
ملخص المحتوى في الصفحة رقم 10
PAGE 10 BIASI B/40 8. Burner Setup: The following information applies only to the BIASI B-40 series boilers at a maximum output for power venters or lined chimneys only. BURNER MANUFACTURER Heatwise Boiler Model B-406 B-407 B-408 B-409 B-410 B-411 B-412 P2-KA P2-K P2-K DE-10 DE-10 DE-10 DE-10 Burner Model Firing Rate 2.2 GPH 2.8 GPH 3.5 GPH 4.25 GPH 5.0 GPH 5.7 GPH 6.4 GPH Insertion Depth FULL FULL FULL FULL FULL FULL FULL Nozzle 2.00 X 45 2.25 X 60 2.75 X 60 3.25 X 60 3.75 X 60 4.5 X
ملخص المحتوى في الصفحة رقم 11
BIASI B/40 PAGE 11 8. Burner Setup: The following information applies only to the BIASI B-40 series boilers at a maximum output for power venters or lined chimneys only. BURNER MANUFACTURER Heat Wise Boiler Model B-406 B-407 B-408 B-409 B-410 B-411 B-412 SU-3 SU-3 SU-4 SU-5 SU-5 SU-6 SU-6 Burner Model Natural Natural Natural Natural Natural Natural Natural Fuel Input 315 420 499 577 672 847 954 Min. Gas Inlet Size 1" 1" 1" 1" 1" 1" 1-1/4" Manifold in w.c. 1.95" 3" 3.5" 2" 2.8" 1.16" 1.
ملخص المحتوى في الصفحة رقم 12
PAGE 12 BIASI B/40 9. Gas Line Piping Gas supply piping is to be sized and installed properly in order to provide a supply of gas sufficient to meet the maximum demand without undue loss of pressure between the meter and the boiler. It is advisable to run a separate gas line from the meter to the gas burner to avoid pressure drops. Consult with the National Fuel Gas Code ANSI Z223.1 for proper sizing of gas piping for various lengths and diameters. Locate a drop pipe adjacent to, b
ملخص المحتوى في الصفحة رقم 13
BIASI B/40 PAGE 13 INSTALLATION OF SEDIMENT TRAP AND BURNER SUPPLY Piping should consist of: 1. A shut off valve approximately 6’ away from the unit. 2. A 1/8” plugged NPT tapping for gas pressure measurement preferably on the manual shut-off valve (as shown or anywhere between the gas valve and the shut off value). Note: The manual shut off valve and tapping are NOT part of the SU-4 Gas Burner. Please make sure you conform to local and state codes. 3. A gas union. 4. A drip pipe.
ملخص المحتوى في الصفحة رقم 14
PAGE 14 BIASI B/40 10. Breeching and Venting: The B-40 Linear boiler is a high efficiency unit that requires proper venting. The boiler must be vented to the outdoors by means of a tile lined masonry or an approved pre-fabricated chimney of the size and height recommended by the manufacturer or by a listed "power venting" unit which provides draft by mechanical venting . The chimney discharge opening must be located at least 24 inches above any part of the building structure
ملخص المحتوى في الصفحة رقم 15
BIASI B/40 PAGE 15 10. Blocked Flue Switch: 1. Pierce a 5/8” hole into the vent pipe near the appliance outlet. Remove one of the securing nuts from the pipe of the safety switch. Tighten the other securing nut onto the pipe as far as possible. 2. Insert the threaded pipe end into the pierced hole, then install the securing nut, then install the se- curing nut, which was removed in step 1, and tighten securely. 3. Please consult the wiring section of this manual for the wiring of the b
ملخص المحتوى في الصفحة رقم 16
PAGE 16 BIASI B/40
ملخص المحتوى في الصفحة رقم 17
BIASI B/40 PAGE 17 12. Boiler Jacket Assembly: NOTE: All piping, boiler controls, gauges and valves must be installed before the jacket has been assembled on the boiler. Refer to the following page to clarify these boiler jacket assembly instructions. Insert the separate piece of insulation (# 92) on top of boiler so the entire top and sides of boiler are covered. Use plastic strapping to secure the insulation in place. Mount the panel installation bracket (#82) onto the draw-r
ملخص المحتوى في الصفحة رقم 18
PAGE 18 BIASI B/40 13. Wiring: The electricity to the boiler shall come from a dedicated breaker in the electric service box. A service switch should be mounted on the side of the boiler so the burner man can service the burner and controls. The electrical wiring should be routed so as not to interfere with normal servicing of the boiler. Wiring done in the field between devices not attached to boiler shall conform with the temperature limitations for type T wire (63F/35C) or other spe
ملخص المحتوى في الصفحة رقم 19
BIASI B/40 PAGE 19 CONTROL PANEL DESCRIPTION 1. On/Off Switch — Turns power to control panel on and off and will disable power to the burner assuming the panel is wired correctly. 2. Minimum Boiler Temperature Thermostat — Maintains a minimum boiler temperature be- tween 50 degrees F and 170 degrees F. 3. Maximum Boiler Temperature Thermostat — High limit temperature setting for boiler be- tween 50 degrees F and 205 degrees F. 4. Thermostat Test Button — This button jumps out both th
ملخص المحتوى في الصفحة رقم 20
B-40 Control Panel Wiring Diagram for Beckett/Heat Wise Oil Burner 24V PAGE 20 BIASI B/40 CIRCULATOR RELAY BURNER CONTROL
