ملخص المحتوى في الصفحة رقم 1
STB1000
HD Commercial Interface Set-top Box
for use in Lodging Environments
Installation & Setup Guide
Warranty
© Copyright 2011, LG Electronics U.S.A., Inc. P/N: 206-4147 (Rev A)
ملخص المحتوى في الصفحة رقم 2
For Customer Support/Service, please call: MODEL and SERIAL NUMBER The model and serial numbers of this STB are located on 1-888-865-3026 the back of the cabinet. For future reference, LG suggests that you record those numbers here: The latest product information and documentation is available online at: Model No._________________Serial No. _______________ www.LGsolutions.com/products WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NO
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 14. Never touch this apparatus or antenna during a thunder or lighting storm. 2. Keep these instructions. 15. When mounting an STB on the wall, make sure not to 3. Heed all warnings. install the STB by the hanging power and signal 4. Follow all instructions. cables on the back of the STB. 5. Do not use this apparatus near water. 16. Do not allow an impact shock or any objects to fall into the product. 6. Clean only with dry cloth
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 23. Cleaning When cleaning, unplug the power cord and rub gently 20. Grounding with a soft cloth to prevent scratching. Do not spray Ensure that you connect the earth ground wire to water or other liquids directly on the STB as electric prevent possible electric shock (i.e., an STB with a shock may occur. Do not clean with chemicals such as three-prong grounded AC plug must be connected to a alcohol, thinners, or benzene. th
ملخص المحتوى في الصفحة رقم 5
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Jack Pack Connections & Setup . . . . . . . . . . . 62 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 – 4 External Equipment Setup . . . . . . . . . . . . . . . . . . . .63 – 65 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Digital Audio Optical Connections / Component Connections . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 6
Setup Checklist Installation and Setup __ Unpack the STB1000 and all accessories. Accessories provided: • 6 ft AC power cord • 5 ft RS-232C-F to RS-232C-F null-modem cable with 3.5 mm stereo plug • 5 ft RS-232C-M to RS-232C-F straight-through cable • 5 ft HDMI to DVI-M cable • 1 ft DVI-F to HDMI adapter cable • 5 ft Audio cable with 3.5 mm stereo plugs • IR receiver with attached 3.5 mm stereo plug cable (3 ft), plus mounting bracket • 5 wall mount brackets with 5 screws for attaching the S
ملخص المحتوى في الصفحة رقم 7
OPTICAL MPI/GAME DIGIT L A LAN TV-LINK CONTROL AUDIO OUT SPEAKER DIGITAL VIDEO IN CFG OUT 8 2 RESET UPDA .......... TE DISPLAY CONTROL REMOTE RGB(PC) AUDIO CONTROL OUT 1(DVI) (RGB/DVI) .......... ..... ..... ..... ..... .... Y PB PR L R VIDEO AUDIO RJP R-AUDIO-L/MONO VIDEO E COMPONENT IN INTERFAC STB1000 Rear and Front Panel Overview STB1000 Rear Panel RGB IN AV IN 1 AC OUT IR RECEIVER AC IN IN INT PILLOW DIGITAL DISPLAY AUDIO OUT VIDEO OUT IR IN PILLOW SPEAKER ANT USB VIDEO L/MONO -
ملخص المحتوى في الصفحة رقم 8
OPTICAL MPI/GAME DIGITAL LAN CONTROL AUDIO OUT TV-LINK SPEAKER DIGITAL VIDEO IN CFG OUT 8 2 RESET UPDATE .......... REMOTE RGB(PC) AUDIO DISPLAY CONTROL 1(DVI) (RGB/DVI) CONTROL OUT .......... ..... ..... ..... ..... .... Y PB PR L R VIDEO AUDIO RJP R-AUDIO-L/MONO VIDEO COMPONENT IN INTERFACE STB1000 Jack Panel Overview UPDATE Restricted to software updates. TV-LINK CFG Use for local FTG configuration. MPI/GAME CONTROL When the EBL is in Pass-through Mode, the MPI function enables an ext
ملخص المحتوى في الصفحة رقم 9
POWER STB1000 STATUS POWER STB1000 STATUS Ventilation / Mounting the STB1000 Ventilation STB1000 The STB1000 generates heat during operation and needs to be provided with Vent Holes adequate ventilation to assure continued reliable operation. See recommenda- tions below. Proper clearance for air to fl ow around the STB1000 must be provided. Note: While accommodating STB1000 ventilation requirements, also be sure proper ventilation is provided for the display panel. Refer to display panel inst
ملخص المحتوى في الصفحة رقم 10
. . . . . . . . . . . . . . . . . . . . . . . . STB1000 Cabling Connections Refer to the cabling diagram below, and complete the procedure on page 11 to connect the STB1000 to a compatible LG display panel. Notes: OPTICAL MPI/GAME DIGITAL LAN CONTROL AUDIO OUT TV-LINK SPEAKER • This diagram shows a typical CFG DIGITAL VIDEO IN OUT 8 2 RESET UPDATE installation using the supplied .......... DISPLAY CONTROL REMOTE RGB(PC) AUDIO RS-232 null-modem cable. CONTROL OUT 1(DVI) (RGB/DVI) .....
ملخص المحتوى في الصفحة رقم 11
STB1000 Cabling Connections (Cont.) 1. Use one of the supplied RS-232 cables—either the serial DB9-Female to DB9-Female null-modem cable or the DB9-Female to DB9-Male straight-through cable, depending on display panel requirements—to connect the DISPLAY CONTROL connector on the STB1000 jack panel to the RS-232 IN connector on the LG display panel. Note: Once the RS-232 connection is made between the STB1000 and the LG display panel, the display panel functions can only be controlled by th
ملخص المحتوى في الصفحة رقم 12
STB1000 Installer Remote The LG Installer Remote is supplied with and dedicated to operate the STB1000. See next POWER TV DVD page for typical key functions. Some DVD and VCR controls may be available for selected STB VCR LG DVD/VCR products. GUIDE PORTAL INFO i Installing Batteries in Installer Remote • Open the battery compartment cover on the back side of the remote. ENTER • Install two high-quality alkaline 1.5V AAA batteries. Never mix old or used batteries with new ones. Install batter
ملخص المحتوى في الصفحة رقم 13
Installer Remote Control Typical Key Functions The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the STB1000. GUIDE TV/STB/DVD/VCR POWER Displays and removes the electronic TV DVD Select the remote’s operating mode: TV, program guide. STB, DVD, or VCR. STB VCR PORTAL GUIDE PORTAL INFO i POWER Displays and removes the interactive menu. Turns STB or any oth
ملخص المحتوى في الصفحة رقم 14
Pro:Centric Interactive Menu Features Important: Pro:Centric operation requires that Installer Menu item 119 DATA CHANNEL be set appropriately and that the STB1000 be in PPV or FTG Mode. The interactive Pro:Centric STB enables guests—from the comfort of their rooms—to Channel Guide view and select from a complete listing of hotel/institution services and amenities. The Information Pro:Centric STB is connected to the institution's billing computer, and service/amenities Remote Help charges a
ملخص المحتوى في الصفحة رقم 15
► STB1000 Setup Menus On-screen setup menus control the basic features of the STB1000/display. Press MENU on the Installer Remote to access the STB1000 setup menus. Setup menu options are described in detail on pages 16 to 38. Note that on-screen displays (OSDs) shown in this manual may differ from those shown on the display panel. This document provides typical examples to familiarize you with the STB1000 options. TIME CHANNEL PICTURE AUDIO Note: The USB menu option is not applicable for the
ملخص المحتوى في الصفحة رقم 16
Channel Setup Options Auto Tuning (Channel Search) Auto Tuning (Channel Search) Move Enter CHANNEL Auto Tuning automatically finds and stores all digital and analog Auto Tuning channels available through antenna or cable inputs. Manual Tuning 1. Press MENU on the Installer Remote, and use the arrow Channel Edit navigation keys to select/highlight the CHANNEL menu Channel Label option. Then, press ENTER. 2. Use the Up/Down arrows to select Auto Tuning, and then Check your antenna connectio
ملخص المحتوى في الصفحة رقم 17
Channel Setup Options (Cont.) Manual Tuning (Add/Delete Channels) / View Digital Signal Strength Manual Tuning (Add/Delete Channels) Move Enter CHANNEL Use this option to manually add active channels or remove unwanted channels. See also “Edit Channels” on the following Auto Tuning page. Manual Tuning Channel Edit 1. Press MENU on the Installer Remote, and use the arrow DIGITAL ► Channel Label navigation keys to select/highlight the CHANNEL menu Select channel type and option. Then, pres
ملخص المحتوى في الصفحة رقم 18
< Channel Setup Options (Cont.) Edit Channels / Channel Labels Edit Channels Move Enter CHANNEL Use this option to add or delete channels from the channel lineup. Auto Tuning Manual Tuning 1. Press MENU on the Installer Remote, and use the arrow Channel Edit navigation keys to select/highlight the CHANNEL menu Channel Label option. Then, press ENTER. 2. Use the Up/Down arrows to select Channel Edit, and then press ENTER. 3. In the Edit Channel pop-up window, active channels are displayed
ملخص المحتوى في الصفحة رقم 19
► Picture Setup Options Aspect Ratio (Picture Size) Control Aspect Ratio (Picture Size) Control Move Enter PICTURE This option enables you to choose the appropriate picture Aspect Ratio : 16:9 aspect ratio depending on the input source. Use the RATIO Picture Mode : Standard button on the Installer Remote or use the procedure below. • Backlight 90 1. Press MENU on the Installer Remote, and use the arrow • Contrast 90 navigation keys to select/highlight the PICTURE menu • Bright
ملخص المحتوى في الصفحة رقم 20
► ► ► Picture Setup Options (Cont.) Picture Mode Picture Mode Move Enter PICTURE This feature enables you to select a preconfi gured Picture Aspect Ratio : 16:9 Mode option and/or customize picture settings manually. Picture Mode : Standard 1. Press MENU on the Installer Remote, and use the arrow • Backlight 90 navigation keys to select/highlight the PICTURE menu Intelligent Sensor • Contrast 90 option. Then, press ENTER. Vivid • Brightness 50 Standard • Sharpness 50 2. To s
