ملخص المحتوى في الصفحة رقم 1
model
s680
ملخص المحتوى في الصفحة رقم 2
CONGRATULATIONS Congratulations for choosing a Directed Featuring silk dome tweeters, propri- Studio neodymium component speaker etary injection-molded baskets and high- system from Directed Electronics. grade neodymium motors, the Directed Studio line of automotive speakers will Directed Electronics has been the excite and delight the auto sound enthu- industry leader in high-quality automo- siast with years of high quality audio tive security and audio equipment since reproduction. 1990, and w
ملخص المحتوى في الصفحة رقم 3
LIMITED TWO-YEAR CONSUMER WARRANTY Directed Electronics, Inc. (DEI) promises to MERCHANTABILITY, FITNESS FOR PARTIC- the original purchaser, to replace this product ULAR PURPOSE, AND WARRANTY OF NON- should it prove to be defective in workman- INFRINGEMENT OF INTELLECTUAL PROPERTY ship or material under normal use, for a ARE EXPRESSLY EXCLUDED TO THE period of two years from the date of MAXIMUM EXTENT ALLOWED BY LAW, AND purchase from the dealer as indicated by the DEI NEITHER ASSUMES NOR AUTHOR
ملخص المحتوى في الصفحة رقم 4
FEATURES Woofer Tweeter Injection-molded graphite cone for New hotter 25mm ferrofluid cooled stiffness and low mass. silk dome tweeter with neodymium magnet. Fiberglass-reinforced injection-molded basket. Swiveling flush and surface mount tweeter housings provided. High-grade neodymium motor structure for higher efficiency. Crossover Supplied inline 12 dB/octave passive crossover. WARNING High-powered car audio They may also impair a driver’s ability to systems may produce sound hear traff
ملخص المحتوى في الصفحة رقم 5
INSTALLATION PRECAUTIONS The Directed s680 neodymium separates distortion or shorting of the speaker are designed for installation into factory leads to the chassis ground. Over- speaker locations, custom mounting sized holes will not allow the enclosures or any flat mounting surface mounting screws to make sufficient inside the vehicle with sufficient rear contact with the panel, allowing the clearance. The following precautions and speaker to become loose. instructions cover the basic and most
ملخص المحتوى في الصفحة رقم 6
cut it to the proper size. If the hole is 8. Place the woofer into the hole and oversize, it is recommended that a attach using the supplied screws. spacer be built to compensate. Take care at this time not to slip with a tool while mounting or the 4. Pre-drill the holes for the mounting speaker could be damaged. screws using a 1/8" drill bit. 9. If using the optional 6x9 adapter 5. Route the supplied wires through ring and grill, place several pieces of the speaker location to the stereo the bu
ملخص المحتوى في الصفحة رقم 7
TWEETER INSTALLATION Review the Installation Precautions 8. Connect the speaker wires observing section of this guide before proceeding. the correct polarity and re-assemble the panel. Flush Mounting into Removed Panels Flush Mounting into Mounted Panels 1. Disassemble the underside of the woofer mounting flange by removing 1. Remove the tweeter from the flush mount housing and insert the the four screws from the bottom side proper length machine bolt through of the tweeter bridge. Twist the top
ملخص المحتوى في الصفحة رقم 8
against the panel and mark the two 8. Insert the tweeter into the housing holes at the rear of the housing. and attach the trim ring. 3. Drill the smaller center hole using a Removing Trim Rings 1/8" drill bit. This is the mounting Hold the tweeter housing while gently screw hole. turning the trim ring in a clockwise direc- 4. Drill the larger off-center hole using a tion until it releases. The trim ring can 3/8" drill bit, insert a grommet and then be easily lifted away from the route the speak
ملخص المحتوى في الصفحة رقم 9
FIGURE 3—FLUSH MOUNTING MOUNTED PANELS
FIGURE 5—TWEETER REMOVAL FROM BRIDGE FIGURE 5—TWEETER SURFACE MOUNTING 9 © 2003 Directed Electronics, Inc
ملخص المحتوى في الصفحة رقم 10
FIGURE 6—CONNECTION/ADJUSTMENT SINGLE AMPLIFIER 10 © 2003 Directed Electronics, Inc
ملخص المحتوى في الصفحة رقم 11
SPECIFICATIONS Directed model 680 Frequency response 40 Hz - 21 kHz Power handling RMS 60 watts Power handling peak 120 watts Impedance 4 ohms Magnet weight 52.82 g Vas 8.8L Fs 68 Hz Qts 0.52 Efficiency (1W/1M) 90 dB Mounting Depth 2-6/8” Mounting hole diameter 7-11/16” x 5-3/8” C Co om mm mo on n D Drriiv ve err S Sp pe ec ciiffiic ca at tiio on ns s:: Magnet type Neodymium Magnet diameter 1-7/8” Voice coil former Kapton Polyimide Voice coil diameter 25 mm (1”) Voice coil layers 4 T Tw we ee
ملخص المحتوى في الصفحة رقم 12
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security, car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, Directed is ISO 9001 registered. Directed Electronics, Inc. Vista, California 92083 Directed® is committed to delivering world-class quality products and services that excit
