ملخص المحتوى في الصفحة رقم 1
APS Power Supply
15, 30, 45, 55, 75, 90 and 100 Amp
Installation Guide
Congratulations and thank you for purchasing a Cascade Audio Engineer-
ing APS Power Supply. It is designed to provide years of efficient, trouble free
service.
All Cascade Audio Engineering APS power supplies feature regulated and
filtered outputs that provide clean power without the slightest hint of noise.
The advanced circuitry utilized in our APS power supplies offer efficiency
ratings of 86-90%. Their super light weight
ملخص المحتوى في الصفحة رقم 2
Protection All Cascade Audio Engineering APS Power Supplies feature temperature, overcurrent and reverse-polarity protection circuitry. They will provide stable regulated DC output voltage (13.6V or 14.2V, relative to jumper connection - The APS-100 is 13.4V only) regardless of the load by varying output current to compensate. AC input protection against damaging spikes of up to 190VAC and brown-out input protection are also provided. All APS Power Supplies feature an automatic, thermally trigge
ملخص المحتوى في الصفحة رقم 3
Your new APS Power Supply can be used with or without an additional bat- tery. Use of a battery connected in parallel with your APS power supply will greatly increase the current available for transients. For installations where use of a battery is not possible, capacitors may be used. Vehicle Installation Two methods of vehicle installation are commonly used. One is to mount the positive and negative battery cables to the vehicle and to place the power supply under the vehicle when necessary. E
ملخص المحتوى في الصفحة رقم 4
Cut the positive and negative cables that will go from the power supply to the load (battery, display board, distribution blocks, etc.) to the desired length. Always use the proper sized cable based on the amperage of the power supply and the distance between the power supply and the load (Please refer to the chart at the end of this manual). Allow for proper routing of the cables. Strip approx. 1” of insulation from one end of each cable. Insert the stripped end of the positive (red) cable into
ملخص المحتوى في الصفحة رقم 5
Connecting Multiple APS Power Supplies APS power supplies may be connected in parallel to increase their current capability. There are a few important steps to follow: 1. APS power supplies must only be connected to other APS units of the same model. Example: An APS-55 can ONLY be connected to other APS-55 power sup- plies. Failure to comply with this step will void your warranty. 2. APS power supplies must be connected in parallel (Positive to positive and negative to negative). 3. It is possib
ملخص المحتوى في الصفحة رقم 6
Fuses Your APS Power Supply is protected against reverse polarity. If the battery or the APS unit is hooked up incorrectly, the fuse on the end panel will blow and can easily be replaced. When replacing fuses, always use the same size AGC style fuses that came with your power supply. The fuses are located next to the DC output terminals (Refer to the picture below). AC Input Cord All APS Power Supplies must be plugged into a 120V AC outlet. They are not equipped with on/off switches. Do not plug
ملخص المحتوى في الصفحة رقم 7
12VDC Cable Calculator MINIMUM wire gauge shown. For MAXIMUM PERFORMANCE, use LARGER wire gauge. 3600 225 - 300 2700 150 - 225 1/0 GA 1800 125 - 150 1500 105 - 125 1260 85 - 105 1020 65 - 85 4 GA 780 50 - 65 600 35 - 50 420 20 - 35 240 0 - 20 8 GA W ATTS AMPS 4 FT 4 - 7 FT 7 - 10' 10 - 13' 13 - 16' 16 - 19' 19 - 22' 22 - 28' CABLE LENGTH Available Accessories CAP-01/CAP-0.5: Cascade Audio Engineering also offers our CAP-1 One Farad and CAP-0.5 One-Half Farad capacitors as well as our bolt-on CAP
ملخص المحتوى في الصفحة رقم 8
Two Year Warranty Cascade Audio Engineering warrants its APS Power Supplies against any elec- tronic or mechanical defects under normal use for a period of two (2) years from the date of original purchase. If, during the first year, it is determined by Cascade Audio Engineering that the unit is defective, it will be directly exchanged for a new unit. If, during the second year, it is determined by Cascade Audio Engineering that the unit is defective, it will be replaced or repaired at the discr
