ملخص المحتوى في الصفحة رقم 1
TOSHIBA REMOTE RECEIPT PRINTER
TRST-A00 SERIES
Owner'sManual
ملخص المحتوى في الصفحة رقم 2
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. ATTENTION Ce produit est de classe A. Dans un environnement domestique, il
ملخص المحتوى في الصفحة رقم 3
Safety Summary ENGLISH VERSION Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this
ملخص المحتوى في الصفحة رقم 4
Safety Summary ENGLISH VERSION If foreign objects (metal When unplugging the power cords, Disconnect Disconnect fragments, water, liquids) enter be sure to hold and pull on the plug the plug. the plug. the machines, first turn off the portion. Pulling on the cord portion power switches and disconnect may cut or expose the internal wires the power cord plugs from the and cause fire or electric shock. outlet, and then contact your authorised TOSHIBA TEC representative for assi
ملخص المحتوى في الصفحة رقم 5
EO1-13027 1.1 Introduction Important Information to the User In order to meet Product Safety, FCC and CE marking requirements, it is advised to use the power supply, power cord, and interface cable which were shipped with this product. Otherwise these devices need to meet following standards: Power Supply The power supply should follow UL/EN/IEC60950 certification, Class 1 power supply with SELV (Secondary Extra Low Voltage), non-energy hazard output, limited power source, inp
ملخص المحتوى في الصفحة رقم 6
EO1-13027 Wichtige Benutzerinformationen: Um die Produktsicherheit sicherzustellen und die FCC und CE-Markierungsanforderungen bei der Benutzung des Druckers zu gewährleisten, müssen folgende Anforderungen erfüllt sein oder das mitgesante Netzgerät, Netzanschlußkabel und Verbindungskabel verwendet werden: Netzgerät: Das Netzgerät muß ein UL verzeichnetes (QQGQ) Netzgerät der Klasse 1 mit SELV (Sekundärextraniederspannung), Nichtenergie Gefahrenausgang, begrenzter Energiequelle
ملخص المحتوى في الصفحة رقم 7
EO1-13027 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW ------------------------------------------------------------ 1-1 1.1 Introduction ----------------------------------------------------------------------------- 1-1 1.2 Features --------------------------------------------------------------------------------- 1-1 1.3 Applicable Model ---------------------------------------------------------------------- 1-2 1.4 Accessory ------------------------------------
ملخص المحتوى في الصفحة رقم 8
EO1-13027 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for purchasing the TOSHIBA TRST-A00 Series Thermal Printer. This printer is a compact line thermal printer designed to be connected to a TOSHIBA POS terminal or used as a Receipt printer, etc. It prints both 80 mm-wide and 58 mm-wide receipts at the maximum print speed of 170mm/sec. The body colour is selectable from Fair White 2(UF/DF) and Cool Black (UC/DC) so that it is possible to coordinate the colour
ملخص المحتوى في الصفحة رقم 9
1. PRODUCT OVERVIEW EO1-13027 1.3 Applicable Model 1.3 Applicable Model Model name description TRST-A - - - - RoHS compliance R: RoHS-Compliant model Destination, Code QM: Standard for Worldwide CN: China US: USA QT: Australia/Korea Custom Model Blank: Standard Model Cx: Custom Model H/W version Blank: Initial version 1: Add collar (TRST-A10 only) 2: With Hing
ملخص المحتوى في الصفحة رقم 10
1. PRODUCT OVERVIEW EO1-13027 1.4 Accessory 1.4 Accessory Receipt Roll (1 pc.) TRST–A00 Safety Reference TRST–A00 Quick Reference 1-3
ملخص المحتوى في الصفحة رقم 11
2. SPECIFICATIONS EO1-13027 2.1 Printer 2. SPECIFICATIONS 2.1 Printer Item Description Printing method Line thermal dot printing method 80 mm (560 dots) Printing width 58 mm (424 dots) Resolution 203.2 dpi x 203.2dpi Printing speed Max. 6.7 ips max (167.5 mm/sec) for 75W, 55W mode 2 color printing Max 50 mm/sec Printing columns 80 mm Paper 42 Column (at 15.6 cpi Standard Character) 56 Column (at 20.3 cpi Compress Character) 21 Column (Korea Fon
ملخص المحتوى في الصفحة رقم 12
2. SPECIFICATIONS EO1-13027 2.2 Options 2.2 Options Option Model Description AC Adapter This AC adapter is for the exclusive use of the TRST-A10/A15 TOSHIBA KIT-A10-ACA-QM-R remote receipt printer. KIT-A10-ACB-QM-R KIT-A10-ACB type is conformed to Level 4 of the California Energy Commission (CEC). Partition This partition is for the exclusive use of the TRST-A10 TOSHIBA remote KIT-A10-P58-QM-R receipt printer. It is installed into the printer when using a 58-mm-wide r
ملخص المحتوى في الصفحة رقم 13
2. SPECIFICATIONS EO1-13027 2.3 Receipt Roll 2.3 Receipt Roll W1 or W2 Paper type Thermal paper rolled with the print side facing outside Width (W1) 80 +/ -1.0 mm Width (W2) 58 +0/ -1.0 mm (With optional 58 mm paper guide) Outer diameter (D) 76 +/-2.0 mm Paper thickness (T) 0.065 +/- 0.005 mm 2 Weight 53 g/m Outer core diameter 21.5 mm Inner core diameter 12.5 +/- 0.5 mm Recommended thermal Only paper rolled onto a core is acceptable, ho
ملخص المحتوى في الصفحة رقم 14
3. APPEARANCE EO1-13027 3.1 Front/Rear View 3. APPEARANCE 3.1 Front/Rear View Front View Rear View Printer Cover LED Top Cover Feed Button Power Switch 3.2 LED and Feed Button POWER LED (Blue) Lights when the power is turned on. ERROR LED (Blinking Blue) The Error LED indicates an error by blinking FEED Button Used to feed receipt paper. A touch of this button causes one line feed. Pressing and holding it feeds the paper continuously. When the
ملخص المحتوى في الصفحة رقم 15
3. APPEARANCE EO1-13027 3. 2 LED and Feed Button Error Status Table Blue LED Blinking (Slow) Problem What to Do Where to Go Receipt paper is low See “Loading the There are about 4 ½ meters, ± 3 meters, Receipt Roll” in (15 feet, ± 10 feet) of paper left. Change chapter 5.3. the paper soon to avoid running out of paper half way through a transaction. Blue LED Blinking (Fast) Problem What to Do Where to Go Receipt paper is out Change the paper now. Do not run a See “Loa
ملخص المحتوى في الصفحة رقم 16
3. APPEARANCE EO1-13027 3. 3 Connectors 3.3 Connectors CAUTION! 1.The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone line or any other cables than the drawer cable to this connector. Doing so may cause a failure of the phone line and this printer. 2.To the DC24V connector (socket connector), do not connect anything other than the built-in AC adapter. 3.The built-in AC adapter is exclusively for this printer. Do not use it for any other
ملخص المحتوى في الصفحة رقم 17
4. SET UP PROCEDURE EO1-13027 4.1 Requirements for Operation 4. SET UP PROCEDURE 4.1 Requirements for Operation This printer has the following requirements: Serial Interface Type The TOSHIBA POS terminal or Personal Computer to be connected must have a serial port. To communicate with the TOSHIBA POS terminal or Personal Computer, an RS-232C interface cable is required. RS-232C cable....... 9 pins USB Interface Type The TOSHIBA POS terminal or Personal Computer t
ملخص المحتوى في الصفحة رقم 18
4. SET UP PROCEDURE EO1-13027 4.1 Requirements for Operation RS-232C cable pin configuration TRST – A00 9 Pin Female 9 Pin Female USB cable connector 2 1 34 Printer View End 4-2
ملخص المحتوى في الصفحة رقم 19
4. SET UP PROCEDURE EO1-13027 4.2 Setting up the Printer 4.2 Setting up the Printer CAUTION! 1. Place the printer on a flat, stable surface. 2. Do not place the printer close to a heater or where it may be exposed to direct sunlight. 3. Avoid locations where the printer may be exposed to high temperature, high humidity or dust. 4.Care must be taken that no condensation occurs in the printer. If it should, however, do not turn ON the power until the condensation is dried. 5. Use
ملخص المحتوى في الصفحة رقم 20
5. INSTALLATION PROCEDURE EO1-13027 5.1 Connecting the Power Cord and Interface Cable 5. INSTALLATION PROCEDURE WARNING! 1. Since the power cord and the interface cable are not provided with this unit, please locally purchase ones which meet the specifications. For detail specifications, please contact your nearest authorized TOSHIBA TEC representative. 2. Before connecting the power cord and cables to the printer, turn the power of the POS terminal and printer OFF. 3. Do not pul
