ملخص المحتوى في الصفحة رقم 1
D315M
ORDERCODE 100100
ملخص المحتوى في الصفحة رقم 2
DLP Digital Projector User’s Guide Safety These safety precautions include information to prevent personal injury and damage to the projector. Safety Definitions WARNING: Statements identify conditions or practices that could result in personal injury. CAUTION: Statements identify conditions or practices that could result in damage to your equipment. Projector Safety WARNING: • Please use the power cord provided. Connect the power cord to a receptacle with a protective
ملخص المحتوى في الصفحة رقم 3
ENGLISH DLP Digital Projector User’s Guide Lamp Safety WARNING: • To replace the lamp, turn off the power and unplug the power cord. To avoid burns, wait 45 minutes before opening the lamp door. Follow all instructions provided in this User’s Guide. See “Changing the Lamp Module” on page 35. • When you open the lamp module door, be careful not to touch the hot surfaces inside. • In the unlikely event of the bulb rupturing, thoroughly clean the area behind the projector and discard
ملخص المحتوى في الصفحة رقم 4
DLP Digital Projector User’s Guide FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
ملخص المحتوى في الصفحة رقم 5
ENGLISH DLP Digital Projector User’s Guide Table of Contents Safety .......................................................................................................... 2 Safety Definitions.............................................................................................................2 Projector Safety................................................................................................................2 Lamp Safety ..........................................
ملخص المحتوى في الصفحة رقم 6
DLP Digital Projector User’s Guide Language Menu ...................................................................................................24 Utilities Menu......................................................................................................25 Status Menu .........................................................................................................26 Reference ..............................................................................................
ملخص المحتوى في الصفحة رقم 7
ENGLISH DLP Digital Projector Quick Start Guide Preface Congratulations on purchasing a DLP™ (Digital Light Processing) projector. The micro portable projector uses the Digital Light Processing (DLP™) technology along with a built-in image manager. DLP ™ technology by Texas Instruments offers crystal clear images with superior quality. A built-in image manager provides alternative settings for users to optimize image quality. In addition, easy-to-use enhanced features, such as digital
ملخص المحتوى في الصفحة رقم 8
DLP Digital Projector User’s Guide Accessories Overview Power Cord There are four different power cords for options, US type, UK type, Euro type and China type. The appropriate Power Cord is included according to your geographical location & safety requirement. If the standard kit does not satisfy your needs, then please contact your dealer for further service. Power Cord Power Cord Power Cord Power Cord (US type) (UK type) (Euro type) (China type) Computer and Video C
ملخص المحتوى في الصفحة رقم 9
ENGLISH DLP Digital Projector User’s Guide Product Profile Front View Speaker Control Pad Zoom Ring Ventilation Hole Focus Ring IR Sensor Lens Cover Adjuster Foot Rear View I/O Connectors Kensington Security Lock AC IN Socket Bottom Panel Fan Cover Lamp Cover Ceiling Mounted Screw ID Label NOTE: • With ceiling installations, use approved mounting hardware & M4 screw. Min. distance from ceiling/wall: 30/50 cm, 12/20 inch for proper ventilation. For
ملخص المحتوى في الصفحة رقم 10
DLP Digital Projector User’s Guide LED Indicator & Control Pad on Projector Source Button (+) EZKEY Same as Source button with function of on the remote control Keystone, Volume, Frequency, and Brightness for quick selection. Auto (-) Same as Auto button Power Button on the remote control Same as Power button on the remote control Lamp Ready LED Indicator Power LED Indicator LED Indicators Message Power LED Indicator Lamp Ready LED Indicator Status Green Co
ملخص المحتوى في الصفحة رقم 11
ENGLISH DLP Digital Projector User’s Guide Remote Control Instruction Laser aperture (pointer/beam) Power LED Power ON/OFF Laser pointer ON Up direction Mouse cursor Left mouse button Right mouse button Enter button Left direction Down direction Right direction button Keystone correction Volume (+/-) Setup menu Mute sound Zoom (+) Auto sync Video source: ie, Zoom (-) composite or component Blank screen Status of
ملخص المحتوى في الصفحة رقم 12
DLP Digital Projector User’s Guide The following buttons are located on the projector Control Pad or on the Remote Control Power Button Switch power on or off. Use the Power button to begin the warm-up period. The power light blinks green during warm-up and stays green when the projector is ready to use. Menu Button Use to display the On-Screen-Display Menus, which provide several options for adjusting the projected image. Auto Button Use to auto adjust the image quality. S
ملخص المحتوى في الصفحة رقم 13
ENGLISH DLP Digital Projector User’s Guide Installation Steps Getting Started 1. Place the projector on a flat surface. 2. Position the projector at the desired distance from the screen. 3. The projection distance is less than 33 feet (10M). CAUTION: • Proper ventilation is import. Don’t block ventilation openings. Never operate this projector in an enclosed area. Do not place the projector on a tablecloth or other soft covering that may block the vents. With ceiling installa
ملخص المحتوى في الصفحة رقم 14
DLP Digital Projector User’s Guide Connecting Input and Output Devices The cables are color coded to assist you in making the connections. You can connect more than one image source at a time. The input source will be detected automatically when enable the “Auto Source” function is enabled in the Status Menu of the OSD MENU. Manually pressing the “Source” button operates selection. The illustration below shows the ports and appropriate cables for connecting external devices to th
ملخص المحتوى في الصفحة رقم 15
ENGLISH DLP Digital Projector User’s Guide Starting the Projector Power on 1. Remove the lens cap 2. Make sure Lamp LED ready in steady orange state. 3. Press Power on the remote control, or Power on the control pad, to turn on the unit. NOTE: • When powered on, both the fans & lamp will be turned on. The power indicator will begin to flash until a video source is found, and the lamp indicator will extinguish when lamp is in normal status. • The projection image will be in full b
ملخص المحتوى في الصفحة رقم 16
DLP Digital Projector User’s Guide Adjustment Adjusting Projector Angle Place the projector on a flat surface and position in the centre horizontally for best viewing. Adjust the projector angle using the Height Height Adjustment Buttons. Adjustment Button Press the Height Adjustment buttons while tilting the projector. The Foot Adjuster will extend accordingly, angled 7 degrees upwards. Foot Adjusters NOTE: Press the Height Adjustment button before adjusting the Foot
ملخص المحتوى في الصفحة رقم 17
ENGLISH DLP Digital Projector User’s Guide Adjusting the Keystone Control To adjust image vertically and make a square image. Adjust the keystone function by pressing the keystone button on the remote control or through OSD menus. Adjusting the Zoom and Pan ZOOM Press the zoom +/- buttons on remote control to enter zoom mode, and use directional keys to pan upward, downward, right, and left. Four times as large Original size as the original size □ Make
ملخص المحتوى في الصفحة رقم 18
DLP Digital Projector User’s Guide Power Off 1. Turn off the projector and image sources in the order listed here. a. Computer b. Projector c. Audio Source (if different from your video source or computer). d. Video source (such as VCR, DVD, HDTV). 2. Press the Power button on the top of the unit or remote control to turn off the power. A confirmation request will appear on the screen asking for reconfirmation of power off request. 3. Press the Power button again to confirm.
ملخص المحتوى في الصفحة رقم 19
ENGLISH DLP Digital Projector User’s Guide On-Screen-Display Menu Format and Description The OSD menu will appear if any button is pressed thru using the control pad and remote control. Input Source OSD Display Logo The projection image will appear in full brightness within 10-15 seconds and the “LUXEON” logo will appear on the screen. No Input Signal “No Input Signal” will show on the screen when there is no active signal detected within 16 seconds. Standby When input s
ملخص المحتوى في الصفحة رقم 20
DLP Digital Projector User’s Guide Ezkey OSD By repeatedly pressing EZKEY the following menu can be scrolled though. The user may adjust it to the desired level through keypads of Auto (-) and Source (+). Keystone Correction Use the (-) and (+) to adjust the vertical keystone level of the image. Frequency Use the (-) and (+) to adjust the frequency. Volume Use the (-) and (+) to adjust the volume level. Brightness Use the (-) and (+) to adjust the display brightn
