ملخص المحتوى في الصفحة رقم 1
D-CinePremiereDP100
User’s manual
R9010111
R9010118
R5976907/00
02/11/2005
ملخص المحتوى في الصفحة رقم 2
Barco n v Digital C i nema Noo rdl aan 5, B-8520 Kuurn e Phone: +32 56.36.8 4 .93 Fa x: +32 56.3 6 .88.62 E-mail : info.bdc.bps@ba rco.com Visi t u s a t the w eb: www.barco.com PrintedinBelgium
ملخص المحتوى في الصفحة رقم 3
Federal Communications Commission (FCC Statement) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inte
ملخص المحتوى في الصفحة رقم 4
ملخص المحتوى في الصفحة رقم 5
Table of contents TABLE OF CONTENTS 1. Safety Instructions.................................................................................................. 3 1.1 General................................................................................................................................ 3 1.2 WarningRiskofFire................................................................................................................... 3 1.3 Ventilation ............................................
ملخص المحتوى في الصفحة رقم 6
Table of contents 2 R59769 07 D-C I NE PREMIER E DP100 02/11/2 005
ملخص المحتوى في الصفحة رقم 7
1. Safety Instructions 1. SAFETY INSTRUCTIONS Overview • General • Warning Risk of Fire • Ventilation •Service • Optical performances • Cabinet maintenance 1.1 General Summary • This equipment is intended for installation in a restricted access location. • Before operating your projector, please read this manual thoroughly, and retain it for future reference. • InstallationandpreliminaryadjustmentsshouldbeperformedbyqualifiedBarcopersonnelorauthorizedBarcoservicedealers. • All warnings on the pr
ملخص المحتوى في الصفحة رقم 8
1. Safety In structions 1.4 Service Protection on Servicing Attempt to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projection unit and cancellation of the warranty. Servicing Donotattempttoservicethisprojectoryourself,asopeningorremovingcoversmayexposeyoutodangerousvoltagepotentialand risk of electric shock! Refer all projector servicing to a qualified Barco service center. Replacement Part
ملخص المحتوى في الصفحة رقم 9
2. Chec k u p the D-Cine Premiere DP10 0 2. CHECK UP THE D-CINE PREMIERE DP100 Which parts have to be checked before starting up! • All covers in place and access doors closed • Power connection to wall outlet • Pressure in the cooling system of the DMD’s. • Exhaust on dirt 2.1 Covers and Access Doors Safety considerations In order to ensure that correct internal airflow is maintained, and that the projector complies with Electro-Magnetic Compatibility requirements, it should always be operated
ملخص المحتوى في الصفحة رقم 10
2. Check u p the D-Cine Premiere DP10 0 2.2 Power Connection to Wall Outlet Power plugged into wall outlet! Image 2-3 Power connection to Wall outlet 2.3 Pressure in the Cooling System Access to the manometer 1. Insert the lock key in the keyhole on the lamp house door and turn the key to the right to unlock the door. (image 2-4) 2. Turn the door to the right to open. Image 2-4 Lamp door opening Reading out the pressure value on the manometer At the top, inside the projector head, a manometer is
ملخص المحتوى في الصفحة رقم 11
2. Chec k u p the D-Cine Premiere DP10 0 Max. Min. Image 2-5 Manometer view A rapid/significant drop in system pressure indicates leakage. Verify whether the circuit shows any visible signs of liquid leakage. Refer the problem to a qualified Barco service center. Minor drops in pressure over time are to be expected. Once the minimum pressure is reached, pre-pressurize to approximately 1 bar (projector off). If this cannot be achieved, proceed to liquid re-filling procedure (Described in the inst
ملخص المحتوى في الصفحة رقم 12
2. Check u p the D-Cine Premiere DP10 0 8 R59769 07 D-C I NE PREMIER E DP100 02/11/2 005
ملخص المحتوى في الصفحة رقم 13
3. Starting up the D -C ine P re mier e D P100 3. STARTING UP THE D-CINE PREMIERE DP100 Overview • Switching On the projector • Starting Image Projection 3.1 Switching On the projector How toswitchOnthe projector 1. First, carry out the projector check up (see "Check up the D-Cine Premiere DP100", page 5). 2. Press the tumbler switch (A) in the “I” position (ON state indicated by a visible red section of the switch). (image 3-1) Note: Ensure that the power tumbler switch on the input panel on th
ملخص المحتوى في الصفحة رقم 14
3. Starting up the D -C ine P re mier e D P100 A Image 3-1 Switching ON the projector A B E MACRO 01 MACRO 02 MACRO 04 MACRO 03 MACRO 06 MACRO 05 MACRO 08 MACRO 07 MACRO 09 MACRO 10 MACRO 12 MACRO 11 MACRO 14 MACRO 13 D C Image 3-2 Control panel status after switching on A Image 3-3 Status lights on projector head 10 R59769 07 D-C I NE PREMIER E DP100 02/11/2 005
ملخص المحتوى في الصفحة رقم 15
3. Starting up the D -C ine P re mier e D P100 3.2 Starting Image Projection Overview • Using the Button control Panel • Using the Touch Screen Panel 3.2.1 Using the Button control Panel How to start image projection 1. Press the lamp ignition button (A). (image 3-4) The lamp ignite, indicated by the built-in Green LED ON (A2). 2. After ignition of the lamp, press the dowser button (B) (image 3-4) The dowser opens, indicated by the built-in Green LED ON (B2). 3. Press the desired selection butto
ملخص المحتوى في الصفحة رقم 16
3. Starting up the D -C ine P re mier e D P100 3.2.2 Using the Touch Screen Panel How to start image projection 1. Start lamp ignition and opening dowser with the toggle buttons on the control panel (see "Using the Button control Panel", page 11). 2. Successively press touch button Home and Macro’s. (image 3-5) The macro menu is displayed. The macro which is active is displayed next to field with inscription “Active”. If the active macro is linked to one of the fourteen push buttons on the contr
ملخص المحتوى في الصفحة رقم 17
4. Cinema O peratio n 4. CINEMA OPERATION Introduction This section explains how trained operators can use the projector for presenting cinema events such as first-run movies stored an a digital media storage device. The digital media storage device or cinema server is connected to one of the A or B input port on the input panel. Cinema Server B A Input Panel to SMPTE A or B Image 4-1 Cinema server connection 4.1 Selecting the Cinema Source Using the Button control panel 1. The factory button as
ملخص المحتوى في الصفحة رقم 18
4. Cinema Oper atio n Theassigned macroisactivated resulting in afullimagedisplay accordingthecinemaprocessing procedure(pre-definedbythe producers). Image 4-3 Macros selection 14 R59769 07 D-C I NE PREMIER E DP100 02/11/2 005
ملخص المحتوى في الصفحة رقم 19
5. Non-Cinema Operatio n 5. NON-CINEMA OPERATION Overview • ACSAR 2 Input facilities • Monitoring ACSAR 2 selected Source • Selecting an ACSAR 2 Source • Remote Control Functionality Introduction Thissectionexplainshowtodisplay“alternativecontent”originatingfromastandarddefinitionorhighdefinitionnon-cinemasource. Such a source routes to a DVI (Digital Visual Interface) port in the D-Cine Premiere DP100 projector head, and bypass cinema processing when selected. ACSAR 2 Input 4 Input 2 Input 3 In
ملخص المحتوى في الصفحة رقم 20
5. Non-Cine ma Operatio n RGBHV Image 5-2 Monitoring ACSAR 2 output signal 5.3 Selecting an ACSAR 2 Source About Macro’s files For any display,the projector interprets incoming signal data according to a selectable “Macro file” defined atthe time ofinstallation or later (e.g. with each subsequent release of a new digital cinema feature), and stored in projector memory. Eachfileisessentiallyacollectionofprocessing/displaysettings optimizedforaparticularcinemafeatureoralternativenon-cinema content
