ملخص المحتوى في الصفحة رقم 1
CIRCULAR SAW
INSTRUCTION MANUAL
Item#3729
MODEL NO: PCSD180T
PLEASE READ THESE INSTRUCTIONS CAREFULLY
TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL
ملخص المحتوى في الصفحة رقم 2
FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION Figure 2 CLOCKWISE TO LOOSEN COUNTER CLOCKWISE TO TIGHTEN SWING NUT CUTTING DEPTH Figure-3 Figure-1 2 1
ملخص المحتوى في الصفحة رقم 3
FUNCTIONAL DESCRIPTION LIST OF MAIN PARTS 1) Battery pack 6) Nut 2) Upper guard 7) Saw blade 3) Base 8) Switch lock 4) Flange 9) ON/OFF switch 5) Lower guard Figure-4 CLAMP NUT Figure 6 TECHNICAL SPECIFICATIONS: Description PCSD180T Rating Voltage 18Volts Nominal power 200W No-load speed 2500min Saw blade Ø6 .49× Ø 0.39inch Cutting dept
ملخص المحتوى في الصفحة رقم 4
3. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY 1. Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may create a risk of fire. 2. A battery operated tool with integral batteries or a separate pack must be recharged only with the specified charger for the battery. A charger that
ملخص المحتوى في الصفحة رقم 5
situations. 9. Use only accessories that are recommended by the manufacturer for your 6. Use safety equipment. Always wear eye protection. Dust mask, non-skid model. Accessories that may be suitable for one tool may become safety shoes, hard hat, or hearing protection must be used for appropriate hazardous when used on another tool. conditions. SERVICE TOOL USE AND CARE 1.Tool service must be performed only by qualified repair personnel. Service or 1. Use clamps or other practical way to
ملخص المحتوى في الصفحة رقم 6
guard is covering the blade before placing the saw down on bench or floor. cutting. Be aware of the time it takes for the blade to stop after switch is released. 18. When operating the saw, keep the cord away from the cutting area and 7. NEVER hold piece being cut in your hand or across the legs. It is important position it so that it will not be caught on the workpiece. to support the work properly to minimize body exposure, blade binding, or 19. Never attempt to saw with the circular saw he
ملخص المحتوى في الصفحة رقم 7
on a soft surface that might block the ventilation slots and result in b. Neutralize with a mild acid such as lemon juice or vinegar. excessive internal heat. Place the charger in a position away from any c. If battery liquid gets in your eyes, flush them with clean water for a heat source. minimum of 2 minutes and seek immediate medical attention. 11. Do not operate charger if it has received a sharp blow, been dropped, or (medical notes: the liquid is 25-35% solution of potassium hydroxide.
ملخص المحتوى في الصفحة رقم 8
use the correction screw. 3. Hold the tool firmly by both handles and work applying light pressure. Adjusting the Cutting depth (See Fig.3&4) INSTALLING AND REMOVING THE BATTERY PACK For the cleanest possible cut, set the cutting depth whenever possible 5 mm deeper than the thickness of the material. Slacken the swing nut for adjusting NOTE: Make sure your battery pack is fully charged. depth of cut, set the cutting depth, and tighten the swing nut again. To install the battery pack in
ملخص المحتوى في الصفحة رقم 9
2) Insert the battery pack into the charger, as shown in Fig 7, making sure you turn out the light. 3) Move charger and battery pack to a location the pack is fully seated in the charger. The red light indicator will where the surrounding air temperature is approximately 65ºF - 75ºF illuminate showing that the battery is being charged. (18-24°C). If charging problems persist, take or send the tool, battery 3) When charging is well done green light will illuminate. The minimum pack and charg
ملخص المحتوى في الصفحة رقم 10
before installing or removing blade. At the desired depth of cut, secure the base by tightening the lever. 1. To remove the blade (Fig.8, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the bolt clock-wise. Then remove the CAUTION: bolt, outer flange and blade. Use a shallow depth of cut, when cutting thin work pieces for cleaner, safer cuts. 2. To install the blade, follow the removal procedure in reverse. After adjusting the depth of cut, always
ملخص المحتوى في الصفحة رقم 11
ridge. OPERATION To avoid a tearing out of the cutting edges when working sensitive area Hold the tool firmly. Set the base plate on the work piece to be cut (if the surface is very smooth crepe tape also enables easy drawing of without the blade making any contact. Then turn the tool ON and wait line), fixing a thin board of wood to the workpiece and sawing through until the blade attains full speed. both will also avoid tearing out effectively. Now simply move the tool forwa
ملخص المحتوى في الصفحة رقم 12
Both brushes should be replaced at the same time. Use only identical carbon Thank you for purchasing a top quality KingCraft product. This Cordless Circular Saw item brushes. Use a screwdriver to remove the brush holder caps. Take out the worn #3729 was tested and meets our stringent quality standards. This product is warranted to be carbon brushes, insert the new ones and secure the brush holder caps. free from manufacturing defects in original materials, including original parts, and t
