ملخص المحتوى في الصفحة رقم 1
Product
Instructions
25734
C O M M U N I C A T I O N S
81-IN6215
Before attempting to connect or operate this product,
06/01/07
please read these instructions completely.
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. CAUTION 2. Retain Instructions - The safety and operating instructions RISK OF should be retained for future reference. ELECTRIC SHOCK! ! 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. CAUTION: TO REDUCE THE RISK OF 4. Follow Instructions - All operating and user instructions should ELEC
ملخص المحتوى في الصفحة رقم 3
2. Open the housing assembly box. Note there is a small roll ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY): of Teflon Tape that will be needed during installation, put it aside. (Picture 2) Power 24VAC, Class 2 Only Teflon Tape ! 52 watts at 24 VAC (accessories) Heater: 50 watts Blower: 2 watts Picture 2 NOTE: This unit is designed for operation in an upright position. Installing the unit upside down may cause damage to the internal equipment, and will void the warranty. 3, Open the d
ملخص المحتوى في الصفحة رقم 4
Installing the Axis 213 Camera 1. Install the camera onto the quick release bracket using (2) 10-32 x 3/8” screws and star washers provided in the packet. 2. In the kit there are (8) aluminum spacers - (4) 1" and Attach cameras using these (2) holes (4) ½". Thread (2) spacers - (1) 1" and (1) ½" - on top of each of the (4) 2" spacers that are already ½" located on the base bracket inside the housing. ½" + 1" spacers 1" 2" 3. Then start (3) 8-32x3/8” phillips head screws onto the 3
ملخص المحتوى في الصفحة رقم 5
Installing Axis 213 Camera (cont.) CAMERA POWER Connect the power plug and the ethernet cable to the back of the camera. 4. Mount the camera assembly in the housing, sliding the (3) open screw slots over the (3) screws in the housing. Slide the bracket forward then tighten the captive screw on the bracket. CONTROL RJ45 Ethernet Connector Captive Screw ALARMS 1 Alarm 1 Blue 2 Alarm 2 Violet 3 Alarm 3 Gray 4 Common White Power Connection - Reference Only +12 VDC -12 VDC (3) screws in housi
ملخص المحتوى في الصفحة رقم 6
Installing Axis 214 Camera Attach cameras using these (3) holes 1" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. 1. Install the AXIS 214 camera to the 2685 mounting plate using the (3) 3mm x 12mm bolt and lock washers provided. 2. The AXIS 214 camer
ملخص المحتوى في الصفحة رقم 7
4. When the locking buttons hit the end of the keyhole slots. Installing Axis 231D/232D Camera Tighten the locking screw. Then put the camera assembly 1. Install the camera onto the quick release bracket. Loosen aside. one of the screws on the bottom of the camera, see diagram below. Locking screw Loosen screw 2. Place quick release bracket onto the bottom of the camera, making sure that the (3) locking buttons line up with the keyhole slots in the Q/R 5. Since the 231D/232D camera
ملخص المحتوى في الصفحة رقم 8
Installing Axis 231D/232D Camera (cont.) 7. Then start (3) 8-32x3/8” phillips head screws onto the (3) ½" spacers inside the housing. Be sure to place the screws so that they line up with the (3) open slots on the quick release bracket, the screws on the bottom of the camera, see diagram below. (3) 8-32 x 3/8"screws 8. Locate the connector block, which is included with the camera. Then located the connector block bracket, which is included with the housing. Attach the block to the
ملخص المحتوى في الصفحة رقم 9
13. Attach the Installing Axis 231D/232D Camera camera assembly to (cont.) the housing by sliding the (3) 11. To manage the input cable running from the connector open screw block to the camera use the (2) cable tie mounts and slots over the cable ties that are located in the housing packet. screws in the housing. Slide the bracket forward, and Cable Tie Mounts the tighten the captive screw on the bracket. Captive screw Cable Ties Open screw slots 12. Now grab the camera assembl
ملخص المحتوى في الصفحة رقم 10
Installing Axis 233 Camera 1. Note the position of the mounting holes on the camera 4. Now remove the Base Bracket. bracket (see diagram below). Camera Bracket Mounting holes Mounting holes for housing 2. Since the 233 camera operates on 24vac, the power board that is located inside the housing is not needed. The remove the power board, start by loosening the screws on the terminal block and disconnect the orange and red wires. 3. With a Phillips head screwdriver remove the (4) machine
ملخص المحتوى في الصفحة رقم 11
Installing Axis 233 Camera (cont.) 6. Mount the Axis 233 camera bracket and Q/R plate (Quick 7. Place the Quick Release plate onto the bottom of the Release plate) as shown. camera, Make sure that the locking screws on the AXIS 233 Quick Release Keyhole Slots camera line up with (Q/R) plate the keyhole slots on the Q/R plate. Slide the camera into the keyhole slots by targeting the locking screw(s). Keyhole Slots Locking Screw Keyhole Slots 8. Turn the camera counter-clockwis
ملخص المحتوى في الصفحة رقم 12
INSTALLING THE HOUSING ASSEMBLY: REMOVING AND ATTACHING THE DOME ASSEMBLY: Be sure the bracket is properly and securely 1. Attach the dome assembly to the housing top by lining mounted to a supporting structure capable of rigidly up the three pins with the three keyhole slots. Insert the ! holding the weight of the entire unit. dome assembly into the housing and then rotate the dome assembly clockwise. Then tighten the (3) screws on the front NOTE: This unit is designed for operatio
ملخص المحتوى في الصفحة رقم 13
POWER WIRING CONNECTING THE TRANSFORMERS (Figure 2) Two plug-in wall transformers are included with the housing. Determine which transformer will be attached to the camera. Use one to provide power for the heater and blower in the Attach the red and orange wires to the terminal points on the housing, and the other for the camera. Determine where transformer . the transformers will be located, then run two sets of power For the transformer which will be used for the heater and wires into the w
ملخص المحتوى في الصفحة رقم 14
Exploded View for Replacement Parts 16 9 8 7 4 6 5 3 2 1 Replacement Parts List Part Number Description 1 RPFD7015 Lower Trim Ring 2 FD7T Tinted Replacement Capsule FD7C Clear Replacement Capsule 3 RPFD703 Dome Clamping Bracket 4 RPFD072 24 Vac Heater 5 RPFD080 (12 Vdc) Blower (Used In 24v Housings) 6 RPFD060 Camera Bracket 7 RPRH707 Connection Pcb 8 RPFD040 Housing Hardware 9 RPFD709 Housing Top 16 RPFD711 Pendant Mount Bracket - 1 -
