ملخص المحتوى في الصفحة رقم 1
EverFocus
Installation / Operation Instructions
EZ610
EZ610
Low Light Inline IP66 Bullet Camera
Low Light Inline IP66 Bullet Camera
EZ630
EZ630
Low Light IR Inline IP66 Bullet Camera
Low Light IR Inline IP66 Bullet Camera
ملخص المحتوى في الصفحة رقم 2
E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N P/N: 4605XZ0610004AR Operation Instruction 2010 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.
ملخص المحتوى في الصفحة رقم 3
Precautions 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equi
ملخص المحتوى في الصفحة رقم 4
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu
ملخص المحتوى في الصفحة رقم 5
Table of Contents 1 Product Overview..............................................................................................................................................7 1.1 Features ..........................................................................................................................................................7 1.2 Accessory Parts List .........................................................................................................................
ملخص المحتوى في الصفحة رقم 6
4 RS-485 Remote Control..................................................................................................................................31 4.1 Remote control with EKB-500 keyboard........................................................................................................31 4.1.1 RS - 485 Wiring ......................................................................................................................................31 4.1.2 OSD Menu Setting by Keyboard
ملخص المحتوى في الصفحة رقم 7
Chapter 1 1 PRODUCT OVERVIEW Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus EZ610/630. Get color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions.
ملخص المحتوى في الصفحة رقم 8
• IP66 weather resistant • Dual voltage (12VDC/24VAC) with line lock to AC supply 1.2 Accessory Parts List Please be careful when you unpack the box and the electronic device inside. Check and make sure that you have all the items listed below inside the original box: • Camera Unit x 1 • Speedy Mount Ring x 1 • Surface Wire Slot Filler x 1 (optional, may vary in different countries) • Operation Manual x 1 • Video Test Cable x 1 • Power Supply Pigtail x 1 • Mounting Kit x 1
ملخص المحتوى في الصفحة رقم 9
1.3 Specifications EZ610 EZ630 Model 1/3" SONY Super HAD II CCD Pickup Device Video Format NTSC, PAL (by model) Picture Elements 768 x 494(NTSC)/ 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 (Sens-up 256x) (Sens-up 256x) ; 0 Lux IR ON S/N Ratio Over 52dB (AGC off) Electronic Shutter 1/60(1/50) ~1/100,000 Video Output Main Output BNC 1.0V p-p 75Ω, Local test output, cable provided. G
ملخص المحتوى في الصفحة رقم 10
Weight 1250 g / 2.275 lbs. Mounting Pattern Speedy-Mount Ring mates with 4” round electrical box; base swivel is 1” NPT – remove base plate for coupling to standard conduit fittings. Certifications CE / FCC 1.4 Dimensions Front view Camera Body 10
ملخص المحتوى في الصفحة رقم 11
1.5 Camera Component Description Speedy-mount Ring Sunshield Use a coin or screwdriver to remove the cover Controls are inside the cover 1 2 3 4 Red: Menu mode Green: Lens mode 1) Reset: To load the factory default configuration press the button, which is inside this hole, for 3 seconds. Please gently insert a thin, non-metallic device into the hole to operate the reset button. 2) Control Key: For setting Lens & OSD menu. Press the mini-joystick and hold for 5 s
ملخص المحتوى في الصفحة رقم 12
1.6 Related Products In addition, you may order the following EverFocus products which are recommended for use with the camera to achieve the best performance: • EverFocus control keyboard (EKB500) • Any EverFocus DVR with RS-485 interface for PTZ control 12
ملخص المحتوى في الصفحة رقم 13
Chapter 2 2 INSTALLATION This chapter will describe, in general terms, how to install the EZ610/630 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. 2.1 Wiring and Mounting Use the template and an appropriate tool to drill 4 holes to attach the speedy-mount ring. If no surface wire will be used, please insert the p
ملخص المحتوى في الصفحة رقم 14
Video & Power cables RS485 cable (optional) White: RS-485 + Black: RS-485 - Power Socket RS-485 cable Connect the power and video cables. Attach the camera to the speedy-mount ring, securing it with the 4 socket head cap screws provided. Video Video In Power RS-485 Optional 12VDC 24VAC Power and Video connection: Note: For details of RS-485 connection please consult chapter 4, for RS-485 setup
ملخص المحتوى في الصفحة رقم 15
2.2 Adjust Camera Position Adjust the viewing angle to the desired direction. With this unique 3-axis positioning system, installers can capture images from virtually any angle, without compromising. The camera can be adjusted in 3 ways. 1st axis Use a hexagon key to loosen this screw to rotate the camera 360° 2nd axis Use a hexagon key to loosen this screw to rotate the camera 180° 15
ملخص المحتوى في الصفحة رقم 16
3rd axis Loosen lock ring and set screw to rotate camera 360° Sunshield To remove or install the sunshield, use the hexagon wrench provided to loosen the screw at sunshield. Loosen this screw Slide rib on interior of sunshield into track on outside of camera body from front to back. 16
ملخص المحتوى في الصفحة رقم 17
Note: When properly installed, the rear of the sunshield is even with the rear of the camera body; improperly extending the sunshield to ‘shade’ the lens can compromise image quality, particularly on the EZ630 IR model. 17
ملخص المحتوى في الصفحة رقم 18
Chapter 3 3 OSD MENU SETUP This chapter introduces how to change RS485 ID and Baud Rate and to configure the camera OSD menu. STEPS If you want to connect to the camera with a keyboard or other RS-485 - controller, please refer to Section 3.2 RS485 ID & Baud Rate setting. Otherwise, please go to STEP 2. Configure the camera, as described below: 3.1 Control Key General Operation Guide Switch between Lens and Menu operation Press and hold ( ~ 5 s) the joystick button fo
ملخص المحتوى في الصفحة رقم 19
NOTE: For those selected items with “ ” sign in the end, there is a sub-menu for further settings. Return to Previous Page Go to “Return” by turning the mini-joystick and press the mini-joystick to return to previous page. Close the Host Menu Screen To close the menu screen, navigate to the “EXIT” item and press the mini-joystick. 3.2 RS485 ID & Baud Rate Setting Default setting for RS-485 is: Protocol: EverFocus or Pelco-D, self detecting (no setup required)
ملخص المحتوى في الصفحة رقم 20
3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets. Lens — DC — Brightness 0~100 (50) Exposure Shutter x256, x128, x64, x32, — — x16, x8, x4, x2, 1/60(NTSC) / 1/50 (PAL), FLK,1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 — AGC — HIGH ; MIDDLE ; LOW ; OFF — SENS-UP — AUTO (x8) ; OFF BLC OFF — — — BLC — Gain — Low, Middle, High Default, Left/Right, Width,
