ملخص المحتوى في الصفحة رقم 1
EVERFOCUS
Indoor Pendent Dome Camera
Operation Instructions
Model No. EPD200
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fiel
ملخص المحتوى في الصفحة رقم 2
6. Cleaning Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the camera lens. 7. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera at temperatures within 0 ℃~ 50℃/32℉~122℉ and humidity between 20%~ 80%. The input power source is 12VDC/24VAC. PREFACE EPD200 is compact, full functioned CCD Color
ملخص المحتوى في الصفحة رقم 3
SPECIFICATION Pickup Device 1/3" SONY Super HAD CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec. PAL: 625 TV lines, 50 fields/sec. Picture Elements 510 x 492 (NTSC); 500 x 582 (PAL) Horizontal Resolution 380 TVL Sensitivity 0.3 Lux /F=1.2 S/N Ratio Over 48dB(AGC Off) Electronic Shutter 1/50(1/60)~1/100,000 Lens Vari-Focal or Fixed Lens Video Output BNC 1.0Vp-p 75ohm Back Light Comp.. On/Off switch Auto Gain Control On/Off switch Flickerless On/Off
ملخص المحتوى في الصفحة رقم 4
DIMENSION DIAGRAM a. Conduit Size 26mm/1.06” b. 80mm/3.15”” 125mm/4.92” 90mm/3.54” 110mm/4.33” HARDWARE OVERVIEW 3
ملخص المحتوى في الصفحة رقم 5
a. Front panel design (For Vari-Focal Lens Model) BLC – Back Light Compensation IRIS LEVEL CONTROL AGC (Automatic Gain Control) FL(Flickerless) BNC Pigtail Slot for Focusing and Testing Module b. Front panel design (For Fixed Lens Model) BLC – Back Light Compensation FL(Flickerless) AGC (Automatic Gain Control) ES(Electronic Shutter) BNC Pigtail Slot for Focusing and Testing Module INSTALLATION 4
ملخص المحتوى في الصفحة رقم 6
This section covers simple steps and detail installation. Please follow instruction for preventing any unnecessary damage. Simple Steps: 1. Connect to 26mm/1.06” EMT Conduit Pipe and lock it with Hex Wrench 2. Open camera bubble cover 3. Connect to testing monitor(optional accessories) 4. Adjust lens, camera position 5. Optional adjust camera setting on Dip Switch 1. Mount Camera 2.5mm Hex 26mm EMT Wrench Conduit Pipe Set Screws Camera a. Pre-install 26mm/1.06” EM
ملخص المحتوى في الصفحة رقم 7
White (+) Black (-) 2. Open Camera Bubble Cover Turn the camera bubble until you see the arrow face to here. 3. Connecting to testing monitor EN220 Connect the BNC Pigtail accessory to the front of the module for help with focusing or video testing. 6
ملخص المحتوى في الصفحة رقم 8
4. Adjust Camera Position and Lens a. Adjust camera position (Tilt angle up to 90 degree): Adjust camera to the position you like. The turning angel is up to 90 degree. Use ‘tool-less’ screws on the side of the module to secure position. Tool-less Screws 90 Degree b. Zoom and focus adjustments (For Vari-focal Lens Model) After the camera was installed, the zoom and focus of the lens must be adjusted. (1) Loosen the zoom ring knob, and then turn the ring towar
ملخص المحتوى في الصفحة رقم 9
FL (Flickerless) When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic shutter at 1/100(S)(NTSC) or 1/120(S)(PAL) automatically, and reduce the flicker immediately. The default setting is OFF. IRIS Level Control (For Vari-Focal Lens Model) Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens. •Turn counterclockwise to L to get darker picture. •Turn clockwise to H to get brighter picture. Electr
ملخص المحتوى في الصفحة رقم 10
Europe Office: Head Office: Albert-Einstein-Strasse 1 12F, No.79 Sec. 1 Shin-Tai Wu Road, D-46446 Emmerich, Germany Hsi-Chih, Taipei, Taiwan TEL: 49-2822-9394-0 TEL: +886-2-26982334 www.everfocus.de FAX: +886-2-26982380 www.everfocus.com.tw China Office: Room B-05D-1, KESHI PLAZA , Shangdi USA L.A. Office: Information Industry Base, 1801 Highland Ave. Unit A Haidian District, Beijing China 100085 Duarte, CA 91010, U.S.A. TEL: +86-10-62973336/37/38/39 TEL: +1-626-844-888
