ملخص المحتوى في الصفحة رقم 1
V.NETWORKS
READ ME FIRST
VN-C11
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
This READ ME FIRST is made from 100 % recycled paper.
Model No. VN-C11
Serial No.
LWT0105-001A
VN-C10_E_01-24.pm6e 1 03.4.24, 10:02 AM
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 6. Do not use this appliance near water - for example, near a batht
ملخص المحتوى في الصفحة رقم 3
Safety Precautions Due to design modifications, data given in this FOR USA AND CANADA instruction book are subject to possible change without prior notice. CAUTION RISK OF ELECTRIC SHOCK WARNING: DO NOT OPEN TO REDUCE THE RISK OF FIRE OR CAUTION:TO REDUCE THE RISK OF ELECTRIC ELECTRIC SHOCK, DO NOT SHOCK. DO NOT REMOVE COVER (OR EXPOSE THIS APPLIANCE TO RAIN BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO OR MOISTURE. QUALIFIED SERVICE PERSONNEL. AVERTISSEMENT: The lightning flash wis
ملخص المحتوى في الصفحة رقم 4
Thank you for purchasing this product. (These instructions are for VN-C11U.) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. Contents Contents ................................................................................................. 4 Introduction Features ................................................................................................. 5 Items Included ..............
ملخص المحتوى في الصفحة رقم 5
Introduction Features • VN-C11 uses a 1/3-inch CCD with 380,000 pixels, enabling monitoring of high quality images. •For the compression method, in addition to the standard JPEG, VN-C11 supports MPEG4 for a wide range of bit rates. (With MPEG4, up to 4 clients can be connected at one time.) • Equipped with an image recording function by motion detection and alarm input. • VN-C11 has a design similar to other CCTV monitoring cameras, allowing peripheral equipment for such cameras to be also used
ملخص المحتوى في الصفحة رقم 6
Introduction Required Operating Environment PC Specifications OS : Windows 2000 (Service Pack 1 or higher) Windows XP Home Edition Windows XP Professional CPU : Pentium III 500 MHz or higher (1 GHz or higher recommended) Memory Capacity : 128 MB or more Hard Disk Space : 20 MB or more Display/Video Card : 1024 X 768 pixels or more, True Color (24 bits or 32 bits) LAN Specifications • 10 BASE-T/100 BASE-TX network connected with IEEE802.3 hubs. Note The PC specifications above are only for a refe
ملخص المحتوى في الصفحة رقم 7
Operating Precautions ● VN-C11 designed for indoor use. For outdoor use, prepare a proper housing to cover and protect the camera. ● The product should not be installed or used in the following locations. • Locations subject to rain or water. • Locations with hot air or oil vapors such as in kitchens, etc. • Locations where the allowed ambient temperature (0 °C to 40 °C) is exceeded. • Locations exposed to X-ray radiation or where strong electrical or magnetic waves are gener- ated. • Locations
ملخص المحتوى في الصفحة رقم 8
Introduction Controls, Connectors and Indicators (Front, top and side views) 2 1 3 4 5 8 7 6 1 Lens mount 5 Screw hole (1/4-20UNC) The mount for attaching a lens. Either a C- For attaching the camera to mount or a CS-mount lens can be used. a fixer or a pan/tilt unit. The screw length must not ex- ceed 7 mm. If a longer screw 2 Back-focus adjustment ring MAX. 7 mm is used, the internal parts of The ring for adjusting back-focus and chang- the camera may be dam- ing the mount method. For adjusti
ملخص المحتوى في الصفحة رقم 9
Controls, Connectors and Indicators (continued) (Side and rear views) 9 ! # $ % 0 1 2 G 2 1 OUT COM ALARM PUSH RESET IRIS @ POWER MONITOR OUT 10BASE-T/100BASE-TX DO NOT CONNECT TO THE TELEPHONE NETWORK For USA & ^ 9 Ventilation opening # [DC 12 V/AC 24 V] Power terminal For the internal cooling fan. Install the cam- For connecting to a DC 12 V or AC 24 V, 50 Hz/ era in a way that does not cover the opening. 60 Hz, power source. (☞ Page 13) 0 [RESET] button $ [ALARM INPUT] terminals Press this b
ملخص المحتوى في الصفحة رقم 10
Preparations Connection Examples LAN Connection VN-C11 MAC address BF LOCK LAN VN-C11 MAC address PC BF LOCK Network Connection VN-C11 MAC address BF LOCK VN-C11 MAC address BF LOCK LAN INTERNET FTP Server PC Images are automatically PC updated at a regular interval. Peer-to-Peer Connection VN-C11 MAC address BF LOCK PC 10 VN-C10_E_01-24.pm6e 10 03.4.24, 10:02 AM Av Pk L H Av Pk L H Av Pk L H ALC LEVEL ALC LEVEL ALC LEVEL Av Pk L H Av Pk L H LEVE
ملخص المحتوى في الصفحة رقم 11
Preparation Procedure Set the camera in the following procedure. Step 1 Connection and Installation Attach a lens and connect the power cable, a LAN cable and an alarm etc. ☞ Page 12 Then, install the camera to a fixer, etc. Fix a wire securely for preventing the camera from falling off. After installing the camera, connect the MONITOR OUT terminal located on the rear panel to the monitor TV and adjust the camera angle. (For back-focus adjustment, ☞ Page 24) Step 2 Setting the Network Install th
ملخص المحتوى في الصفحة رقم 12
Preparations (Step 1 Connection and Installation) Attaching a Lens Attach a lens in the following procedure. 1. Before attaching a lens, check the mount method of the lens. VN-C11 is set for CS-mount at the factory. For attaching a C-mount lens, loosen the back- focus locking screw using a screwdriver and turn the back-focus adjustment ring to change the mount method accordingly with a finger or a pointed tool like a screwdriver. To attach a lens, observe the length shown as (a). Do not use a l
ملخص المحتوى في الصفحة رقم 13
Connecting the Power Cord Connect the camera to DC 12 V or AC 24 V. The power indicator is lit when the power is turned on. To Power Power Cord • Do not connect the power cord to DC 12 V and AC 24 V at the same time. • Use a lug plate to securely connect the power cord to the power terminals and avoid 1 2 OUT COM G 2 1 misconnection or loose connection. •For DC 12 V connection, ensure that the polarities, positive and negative, are correctly ALARM oriented. •For DC 12 V connection, the ripple v
ملخص المحتوى في الصفحة رقم 14
Preparations (Step 1 Connection and Installation) Connecting a LAN Cable Connect the camera to a hub or a PC by using a LAN cable. • For hub connection Use a straight cable. 1 2 G OUT COM 21 • For PC connection Use a cross-over cable. ALARM PUSH Caution POWER MONITOR OUT 10BASE-T/100BASE-TX There are a few types of LAN board for DO NOT CONNECT TO THE TELEPHONE NETWORK which a cross-over cable cannot be used. For USA Check the specifications of the LAN board to be used before performing connectio
ملخص المحتوى في الصفحة رقم 15
Installing the Camera Fall-Preventive wire For attaching the camera to a fixer or a rotating platform, use the screw hole of the mounting bracket. Camera mounting screw hole Camera-mounting bracket Caution ● The length of the screw for mounting the camera must not exceed 7 mm. Do not MAX. use a longer screw as it 7 mm may damage the internal parts of the camera. ● In the factory setting, the bracket is attached on the top of the camera. For attaching it at the Fall-preventive holes Screws for
ملخص المحتوى في الصفحة رقم 16
Preparations (Step 2 Setting the Network) Installing the Software For operating VN-C11, install the software from the CD-ROM, which is supplied with ~~~~~~~~~~~~~~~ the camera in the following procedure. Installing V.Networks Controller 1. Select [Setup.exe] found in the [JVC] folder. 2. Proceed by following the instructions shown on the screen. 3. If the installation is successfully executed, the [V.Networks] icon is created in [Programs] of the Windows [Start] menu. [V.Networks Controller] is
ملخص المحتوى في الصفحة رقم 17
Setting the PC’s IP Address for Windows XP After attaching the camera, proceed to set the IP address of the PC by which the camera is operated. With Windows XP, follow the procedure below to set the IP address. (For Windows 2000, ☞ Page 19) Note Under a DHCP environment and also if the IP address to be allotted to [V.Networks] is already known, skip Setting the PC’s IP Address. 1.Click . • Right-click [My Network] and select [Properties]. 2.Select the network connected to the PC by which VN-C11
ملخص المحتوى في الصفحة رقم 18
Preparations (Step 2 Setting the Network) Setting the PC’s IP Address for Windows XP (continued) 3. Select [Internet Protocol (TCP/IP)] and click [Properties]. Select [Internet Protocol (TCP/IP)]. Click [Properties]. 4. Select [Use the following IP address] to set [IP Address] and [Subnet Mask] and then click . Select [Use the following IP address]. Set [IP Address] to “192.168.0.3.” Note ● Before changing the IP address, note down the original address. ● Do not use the same IP address elsew
ملخص المحتوى في الصفحة رقم 19
Setting the PC’s IP Address for Windows 2000 After attaching the camera, proceed to set the IP address of the PC by which the camera is operated. With Windows 2000, follow the procedure below to set the IP address. 1. Click . Select [Settings] and click [Control Panel]. 2. Double-click [Network and Dial-up Co...]. 3. Double-click [Local Area Connection]. Select [Internet Protocol (TCP/IP)]. Click [Properties]. 19 VN-C10_E_01-24.pm6e 19 03.4.24, 10:03 AM
ملخص المحتوى في الصفحة رقم 20
Preparations (Step 2 Setting the Network) Setting the PC’s IP Address for Windows 2000 (continued) 4. Click [IP Address] in [TCP/IP properties]. Select [Use the following IP Address]. Set the IP address to “192.168.0.3.” Set [Subnet mask] to an appropriate value according to the operating environment. Ask the network administrator if necessary. 5. Click . 20 VN-C10_E_01-24.pm6e 20 03.4.24, 10:03 AM
