ملخص المحتوى في الصفحة رقم 4
Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below. The pin assignment of the lens connector is as follows: Pin 1: Power source; +9 V DC, 50 mA max. Rib Pin 3 Pin 2: Not used Pi
ملخص المحتوى في الصفحة رقم 5
SETUP 1. CAMERA SETUP MENU This camera utilizes a user setup menu that is displayed on-screen. • Opening the Setup Menu Press and hold down for 2 seconds or Highlighted more. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC The CAM SET UP menu appears on the SHUTTER OFF AGC ON monitor as shown at right. SENS UP OFF Check the current settings on the menu. SYNC INT WHITE BAL ATW MOTION DET OFF LENS DRIVE DC END SET UP DISABLE Refer to the se
ملخص المحتوى في الصفحة رقم 6
SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. To edit the CAMERA ID 1. Move the cursor to the CAMERA ID parameter. 2. Press . The CAMERA ID menu appears. The cursor on the letter “0” is highlighted. 3. Move the cursor to the character you Character Cursor want to e
ملخص المحتوى في الصفحة رقم 7
2-2. ALC Mode with SUPER-D2 OFF and ELC Mode Note: If ELC is selected, set MASK SET according to this procedure. 1. Move the cursor to the SUPER-D2 parameter and select OFF. (When you ** ALC CONT ** select ELC, SUPER-D2 is not avail- BACK LIGHT COMP able.) The item MASK SET appears on SUPER-D2 OFF the menu. MASK SET LEVEL ...I..... - + RET END 2. Move the cursor to MASK SET and press . 48 mask areas appear on the monitor screen. The cursor is blink- Blinkin
ملخص المحتوى في الصفحة رقم 8
1. Move the cursor to the SYNC parameter and select line-lock (LL) or internal (INT). 2.Press . If LL is selected, the SYNC menu appears. (If INT is selected, the synchronization mode is automatically set to internal sync pulse, and the menu is not displayed.) Important Notice: 1. The priority for the sync modes is as follows: 1. Multiplexed Vertical Drive (VD2) (Highest priority) 2. Line-lock (LL) 3. Color Composite Video or Blackburst Signal (VBS) 4. B/W Composite Video or Composite Sync Signa
ملخص المحتوى في الصفحة رقم 9
8. Adjust the horizontal phase by pressing or . The adjustable range is 0-2.0 µs. 6-3. Line-lock Sync Mode (LL) Note: The line-lock (LL) sync mode is not available when the camera operates on DC power. 1. Move the cursor to the SYNC parameter and select LL. Note: The settings in this menu can be made only when the multiplexed vertical drive signal (VD2) is not supplied to the camera. 2. After confirming that the cursor is on LL, press . The vertical phase ** SYNC ** adjustment menu appears
ملخص المحتوى في الصفحة رقم 10
8. Motion Detector Setting (MOTION DET) The motion detector detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection. When this camera is connected to a compatible intelligent CCTV system, the camera trans- mits an alarm signal by multiplexing it with the video signal. 1. Move the cursor to the MOTION DET ** MOTION DETECT ** parameter and select ON. LEVEL ....I.... 2. Press . The MOTION DETECT menu
ملخص المحتوى في الصفحة رقم 11
SPECIFICATIONS Pick-up Device: 771 (H) x 492 (V) pixels, Interline Transfer CCD Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Scanning: 525 lines/60 fields/30 frames Horizontal: 15.734 kHz Vertical: 59.94 Hz Synchronization: Internal, Line-locked, External (VS/VBS) or Multiplexed Vertical Drive (VD2) selectable Video Output: 1.0 V[p-p] NTSC composite 75 Ω /BNC connector Horizontal Resolution: 480 lines Signal-to-Noise Ratio: 50 dB (AGC OFF, weight ON) Dy
ملخص المحتوى في الصفحة رقم 1
CP460
Color CCTV Cameras
Operating Instructions
Model No. WV-CP460
WV-CP464
(Lens Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0100-1020 YWV8QA5377BN Printed in Japan
N 19
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
CAUTION Rules. These limits are designed to provide
reasonable protection against harmfu
ملخص المحتوى في الصفحة رقم 2
FEATURES 1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. Dynamic range of 46 dB. (3) Various External Sync Functions, including Gen-Lock (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB 3. Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lens
ملخص المحتوى في الصفحة رقم 3
6. High quality picture: (a) 2H type vertical enhancer for greater picture sharpness (b) Chroma averaging circuit for better color signal-to-noise ratio (c) Minimum of aliasing on fine objects (d) Expanded dynamic range by use of knee circuit (e) Highlight aperture correction for greater picture detail of bright objects 7. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC) function. 8. Selectable electronic sensitivity enhancing modes including AUTO, MAN
