ملخص المحتوى في الصفحة رقم 1
INST ALLA TION
IS110 Series
®
Camclosure
Integrated Camera System
C3426M-D (3/08)
ملخص المحتوى في الصفحة رقم 2
2 C3426M-D (3/08)
ملخص المحتوى في الصفحة رقم 3
Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Parts List. .
ملخص المحتوى في الصفحة رقم 4
List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Basic Surface Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 4S Electrical Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4 404 Plaster Ring Installation . . . .
ملخص المحتوى في الصفحة رقم 5
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provi
ملخص المحتوى في الصفحة رقم 6
Description ® The IS110 Series Camclosure integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple mounting options. The unit supports both BNC and unshielded twisted pair (UTP) video wiring. The IS110 Series system can be installed directly to a ceiling, wall, 4S electr
ملخص المحتوى في الصفحة رقم 7
The IS111 models include the following specifications: Indoor/outdoor dome, vandal resistant, surface mount, clear bubble, liner, and gray finish Table B. IS111, Clear Bubble with Liner Camera Type Lens/Iris NTSC PAL Color, Wide Dynamic 3 to 9.5 mm, Day/Night Varifocal, Auto Iris IS111-DWV9 — Range, Day/Night 9 to 22 mm, Day/Night Varifocal, Auto Iris IS111-DWV22 — Color, High 3 to 9.5 mm, Day/Night Varifocal, Auto Iris IS111-DNV9 IS111-DNV9X Resolution, Day/Night 9 to 22 mm, Day/Night Varifoca
ملخص المحتوى في الصفحة رقم 8
SHIPPING BOX CAMERA MODULE COVER AND 1 EA. BACK BOX 1 EA. TRIM RING AND < OR > TRIM RING, LINER, SMOKED BUBBLE AND CLEAR BUBBLE 1 EA. 1 EA. BLACK PLUG 1/8-INCH HOLLOW 1 EA. SCREWDRIVER BIT 1 EA. SHOWN ACTUAL SIZE 6-32 X 0.75-INCH 8-32 X 0.75-INCH 8-32 X 0.75-INCH 8-32 X 0.375-INCH PHILLIPS PAN HEAD PHILLIPS FLAT HEAD PHILLIPS PAN HEAD PHILLIPS PAN HEAD SCREWS SCREWS SCREWS SCREWS WITH 3 EA. 2 EA. 2 EA. WASHERS 2 EA. Figure 1. Package Components 8 C3426M-D (3/08)
ملخص المحتوى في الصفحة رقم 9
Cover and Back Box Installation The IS110 Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. You can also wire it through a side conduit. UNSHIELDED TWISTED PAIR VIDEO The IS110 Series offers support for unshielded twisted pair (UTP). The UTP video output signal is 1 Vp-p differential into a 100-ohm load. At a minimum, UTP requires Cat5, 100-ohm twisted pair cable. BASIC SURFACE INSTALLATION NO
ملخص المحتوى في الصفحة رقم 10
8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover. COVER MOUNTING SCREWS (NOT SUPPLIED) BACK BOX 8-32 X 0.375-INCH PHILLIPS PAN HEAD SCREWS WITH WASHERS (SUPPLIED) Figure 2. Basic Surface Installation 4S ELECTRICAL BOX INSTALLATION NOTE: You should
ملخص المحتوى في الصفحة رقم 11
6. Connect the power wires, refer to Table D. Table D. Power Input: 4S Electrical Box Installation Voltage Red Wire Black Wire 12 VDC + Ground 24 VAC ~ ~ AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one side of the transformer to the red wire on all units; connect the other side of the transformer to the black wire on all units. NOTE: Failure to connect all AC powered units in the same way will cause the cameras to be out of phase with each ot
ملخص المحتوى في الصفحة رقم 12
404 PLASTER RING INSTALLATION NOTE: You should install the camera module into the back box before installing the back box into the cover. When installing the back box into the cover, rotate the camera module to access the mounting holes (refer to Camera Module on page 16 for more information). 1. Remove the two 8-32 x 0.375-inch Phillips pan head screws and washers to separate the cover from the back box. 2. Pull video and power wires into the cover. 3. Use up to three supplied 6-32 x 0.75-in
ملخص المحتوى في الصفحة رقم 13
6. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover. CEILING/ WALL 404 PLASTER RING (NOT SUPPLIED) COVER 6-32 X 0.75-INCH OR 8-32 X 0.75-INCH PHILLIPS PAN HEAD SCREWS (SUPPLIED) BACK BOX 8-32 X 0.375-INCH PHILLIPS PAN HEAD SCREWS WITH WASHERS (SUPPLIED) F
ملخص المحتوى في الصفحة رقم 14
SIDE CONDUIT INSTALLATION NOTE: You should install the camera module into the back box before installing the back box into the cover. When installing the back box into the cover, rotate the camera module to access the mounting holes (refer to Camera Module on page 16 for more information). 1. Remove the two 8-32 x 0.375-inch Phillips pan head screws and washers to separate the cover from the back box. 2. Attach the cover to the mounting surface (hardware not supplied). Use stainless steel har
ملخص المحتوى في الصفحة رقم 15
8. Connect the video cable/wires: • BNC: Connect the BNC connector from the unit to a mating BNC connector. • UTP: Connect the blue wire to Video +; connect the gray wire to Video -. 9. Connect the power wires, refer to Table F. Table F. Power Input: Side Conduit Installation Voltage Red Wire Black Wire 12 VDC + Ground 24 VAC ~ ~ AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one side of the transformer to the red wire on all units; connect the o
ملخص المحتوى في الصفحة رقم 16
Camera Module The IS110 Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module. WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting the camera. This applies to all models. MODULE REMOVAL To remove the camera module from the back box: 1. Gently squeeze the bracket and pull
ملخص المحتوى في الصفحة رقم 17
2. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 7). CAMERA HEATER BOARD SERVICE CONNECTOR CONNECTOR CONNECTOR Figure 7. Back Box Connectors C3426M-D (3/08) 17
ملخص المحتوى في الصفحة رقم 18
CAMERA ORIENTATION At the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image could be upside down or sideways. To change the camera orientation (refer to Figure 8): 1. Remove the camera module from the back box if necessary. 2. Remove the tilt adjustment screw and lock washer from each side of the camera. 3. Carefully rotate the camera 180 degrees clockwise. Make sure the wiring harness does not bind. WARN
ملخص المحتوى في الصفحة رقم 19
Camera Adjustments To perform the following camera adjustments, make sure to plug in the camera and service connectors. You may have to remove the camera module from the back box. Connect a monitor. Then turn on power to the camera and monitor. To use the service connector, refer to Service Connector on page 30. To set the DIP switches, or to adjust the auto iris level (DN or CH) or the vertical phase (DW or CW), you will need a miniature trimpot adjustment tool with a 0.05-inch (1.27 mm) bla
ملخص المحتوى في الصفحة رقم 20
DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS110-DN or IS110-CH model. Figure 10. Adjusting the IS110-DN/CH Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Auto Gain Control The auto gain control (AGC) adjusts the image automatically to compensate for changes in light levels. Set SW4-1 to ON to enable AGC. Set it to OFF to disable AGC. The default setting is ON. SW4-2: Backlight Compensation The backlight compensation (
