ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
L73Q4/US GB 2001, 6, 18 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If FEATURES you need help with installation and/or settings, please consult your dealer. • Built-in interline transfer method 1/3" CCD, approx. 270,000 picture elements CONTENTS • Low smear, anti-blooming, low lag, no burning and no geometric distortion using the CCD solid state image device. INFORMATION TO USER ...............................
ملخص المحتوى في الصفحة رقم 3
L73Q4/US GB 2001, 6, 18 INFORMATION TO USER This equipment has been tested and found to comply with the limits Safety Guard for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against THIS SYMBOL INDICATES THAT THERE ARE harmful interference in a residential installation. This equipment IMPORTANT OPERATING AND MAINTENANCE generates, uses, and can radiate radio frequency energy and, if INSTRUCTIONS IN THE LITERATURE ACCOMP
ملخص المحتوى في الصفحة رقم 4
L73Q4/US GB 2001, 6, 18 PRECAUTIONS In case of problem Protect from humidity and dust Do not use the camera if smoke or a strange odour comes from the To prevent damages to the camera, do not install it where there is unit, or if it seems not to function correctly. Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. Service Centre). Protect from high temperatures Do not
ملخص المحتوى في الصفحة رقم 5
L73Q4/US GB 2001, 6, 18 PARTS NAMES 1 Power indicator (POWER) 345 Comes on when the power to the camera is on. 2 Camera setup section PAHSE 2 SHUTTER VIDEO OUT • Internal sync (INT)/Line lock (LL) setting INT LL EI AI • Electronic iris (EI)/Auto iris (AI) setting OFF BLC OFF AGC POWER 1 • Backlight compensation (BLC) setting • Automatic gain control (AGC) setting AC 24 V GND 3 Line phase adjustment volume (PHASE) 6 When using two cameras or more, the image on the monitor may roll vertically when
ملخص المحتوى في الصفحة رقم 6
L73Q4/US GB 2001, 6, 18 PARTS NAMES F Flange-back lock screw G Lens mount cap The cap is installed to protect the lens mount section. F Remove the lens mount cap before installing a lens (sold separately). G H Camera installation bracket The bracket can be fixed at the top or bottom of the camera. A Camera mounting screw hole: 1/4"-20 UNC CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. H A English 5
ملخص المحتوى في الصفحة رقم 7
L73Q4/US GB 2001, 6, 18 PARTS NAMES Concerning auto-iris lenses DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is H referred to as DC type coil lens or DC type non-amplifier lens. LEVEL (Set the Auto-iris lens switch to the DC position.) L DC LENS VIDEO type auto-iris lens VIDEO A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifie
ملخص المحتوى في الصفحة رقم 8
L73Q4/US GB 2001, 6, 18 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 9 mm. If not, that may damage the camera and prevent proper installation. L 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens 1 Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens To allow for flange-back adjustment, install th
ملخص المحتوى في الصفحة رقم 9
L73Q4/US GB 2001, 6, 18 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. 1 Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout DC type lenses VIDEO type lenses 2 1 2 1 Brake coil (–) +10 V DC (50 mA max.) 1 4 3 Brake coil (+) Not
ملخص المحتوى في الصفحة رقم 10
L73Q4/US GB 2001, 6, 18 CONNECTIONS 3 1 (A) 2 (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are 3 Insert the plug of this power cord into a wall outlet. sold separately. The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. Coa
ملخص المحتوى في الصفحة رقم 11
+ L73Q4/US GB 2001, 6, 18 SETTINGS Camera setup section Iris function setting Use a manual or fixed iris lens and set the lens INT LL EI AI aperture to the shortest F stop. Set the EI/AI EI AI switch to EI position. BLC OFF When using an auto-iris lens (for indoor/outdoor use) AGC OFF Set the EI/AI switch to the AI position. • Internal sync (INT)/Line lock (LL) setting Note: • Electronic iris (EI)/Auto iris (AI) setting • The electronic iris is suitable for normal indoor use. When the EI/AI swit
ملخص المحتوى في الصفحة رقم 12
L73Q4/US GB 2001, 6, 18 SETTINGS Lens iris adjustment Backlight compensation setting If using a DC type auto-iris lens, you will need to set the LEVEL Use an auto-iris lens and set the BLC switch to volume when shooting in the conditions described below. the BLC (ON) position, to engage the BLC OFF backlight compensation function. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room If using a VIDEO type auto-iris lens
ملخص المحتوى في الصفحة رقم 13
L73Q4/US GB 2001, 6, 18 SETTINGS High speed electronic shutter setting Line phase adjustment Normally, the speed setting switch for the high When using a camera switcher to connect 2 cameras or more to one 0 1 speed electronic shutter set to the 0 position. monitor, there may be a vertical roll of the images when switched. In 2 This sets the electronic shutter speed to 1/60 sec. such a case, set as described below. 3 4 The switch can be set as indicated in table A to 7 5 1 Set the INT/LL switch
ملخص المحتوى في الصفحة رقم 14
L73Q4/US GB 2001, 6, 18 TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen • Is the power turned on to all connected devices? Is the voltage correct? • Are all the signal connecting cables correctly connected? • Is the lighting sufficient? • Has the lens cap been removed? • Is the lens type
ملخص المحتوى في الصفحة رقم 15
– g L73Q4/US GB 2001, 6, 18 SPECIFICATIONS Scanning system : EIA standard Power supply : 24 V AC, 60 Hz (525 TV lines, 30 frames/sec.) Power consumption : 4.0 W (with auto iris lens) Interlace : 2:1 interlace 3.7 W (without auto iris lens) Image device : 1/3 inch solid state image device CCD Weight : Approx. 560 g (without lens) Picture elements : 542 (H) x 494 (V) Effective picture elements : 512 (H) x 492 (V) Synchronizing system : Internal sync (INT), Line lock (LL) SERVICE manually switchab
ملخص المحتوى في الصفحة رقم 16
L73Q4/US GB 2001, 6, 18 SPECIFICATIONS ACCESSORIES Dimensions 1 Lens iris plug (4-pin)..................................................................1 pc. 2 Hexagonal wrench....................................................................1 pc. 60 135 123 7 12 PHASE SHUTTER VIDEO OUT INT LL EI AI BLC OFF AGC OFF 60 POWER AC 24V GND 11 29 1/4”–20 UNC 40 28 Features and specifications are subject to change without prior notice or obligations. English 15
ملخص المحتوى في الصفحة رقم 17
L73Q4/US GB 2001, 6, 18 SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below. For product operation, authorized service center referral, servi
ملخص المحتوى في الصفحة رقم 18
L73Q4/US GB 2001, 6, 18 1AC6P1P2433-- 21605 Plummer Street, L73Q4/US(0501KP-TVS) Chatsworth, California 91311 98230002 Printed in Taiwan
