ملخص المحتوى في الصفحة رقم 1
PER-E01
Jp
Instruction Manual
En
Underwater Extension Ring for PT-E Series
Mode d’emploi
Fr
Bague d’extension sous-marine pour la série PT-E
Bedienungsanleitung
De
Unterwasser-Zwischenring für PT-E Serie
Manual de instrucciones
Sp
Aro de extensión para usar debajo del agua para la serie PT-E
Cs
Kr
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
1
ملخص المحتوى في الصفحة رقم 4
2
ملخص المحتوى في الصفحة رقم 5
3
ملخص المحتوى في الصفحة رقم 6
4
ملخص المحتوى في الصفحة رقم 7
5
ملخص المحتوى في الصفحة رقم 8
MENU 6 MENU
ملخص المحتوى في الصفحة رقم 9
7
ملخص المحتوى في الصفحة رقم 10
8
ملخص المحتوى في الصفحة رقم 11
Thank you for buying this product. To assure safe and correct use of this product, please read this instruc- tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. This product is a Waterproof Extension Ring (PER-E01) for use with the PT-E series waterproof case. It is designed to be used in combination with the “ZUIKO DIGITAL 1.4X TELECONVERTER (EC-14)” rear converter model. Underwater zooming and manual focusing are not
ملخص المحتوى في الصفحة رقم 12
1 Name of Parts PER-E01 main body Silicon O-ring (POL-E101) Front cap Rear cap PT-E series waterproof case mount Grease for silicone O-ring Pick for O-ring removal Waterproof lens port mount * This product has been designed for exclusive use with the following rear converter. It cannot be used in combination with any other rear converter. Corresponding rear converter ZUIKO DIGITAL 1.4X TELECONVERTER EC-14 2 Mounting the PER-E01 between the Waterproof Case and the Waterproof Lens
ملخص المحتوى في الصفحة رقم 13
Align the threaded section of the PER-E01 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PER-E01 with your other hand and screw it into the PT-E series by turning the PER-E01 clockwise. Resistance increases as the PER- E01 is screwed in more deeply. However, be sure to screw it in all the way until there is no gap visible below the threaded section of the PER-E01. Screw in until there is no gap. Align the thre
ملخص المحتوى في الصفحة رقم 14
3 Dismounting the PER-E01 If any water is on the product, wipe it completely away and make sure that the product is dry. Holding the PT-E series case firmly with one hand, loosen the PPO-E series lens port that is attached to the PER-E01 by turning the PPO-E about 90 degrees counterclockwise. If the PPO-E is screwed in too tight, wrap it with a piece of rubber or other slip-resistant material. After loosening the PPO-E series lens port, point its lens down and turn it further counterclockw
ملخص المحتوى في الصفحة رقم 15
4 Loading the Camera and Lens After installing the EC-14 ZUIKO DIGITAL 1.4X TELECONVERTER rear converter between the camera and lens, insert the camera and lens into the PT-E series case on which the PER-E01 and the PPO-E series lens port are mounted. Screw the camera table provided with the PT-E Remove the eyecup from the camera’s viewfind- series case firmly into the bottom of the cam- er. If a lens cap or filter is attached to the lens or era. the strap is attached to the camera, remove
ملخص المحتوى في الصفحة رقم 16
CAUTION: When this product is used in combination with a zoom lens, zooming of cannot be controlled after the camera has been loaded in the case. Be sure to set the zoom ring of the lens to the desired focal distance before loading the camera in the case. Pull out the zoom dial further. MENU Confirm that the camera’s power switch is OFF. After inserting the camera, turn the camera table While pulling out the zoom dial on the PT-E lock lever of the PT- E series case all the way series case,
ملخص المحتوى في الصفحة رقم 17
5 Maintenance For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product. After shooting, remove the inserted cam- After making sure that the PT-E series era and lens, then re-seal the empty case is completely dry remove the case and immerse it in tap water to PPO-series lens port and this prod
ملخص المحتوى في الصفحة رقم 18
6 Specifications Applicable case : PT- E series Corresponding lens port : PPO-E01/PPO-E02/PPO-E03 Underwater zooming and manual focusing are not possible when this product is used. Applicable lens : ZUIKO DIGITAL 1.4X Teleconverter EC-14 Main materials Main body : Aluminum. O-rings : Silicon rubber. Front cap : ABS resin. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 108 mm x Depth 36.1 mm Weight : 220 g (excluding the conversion
ملخص المحتوى في الصفحة رقم 19
Nous vous remercions d’avoir acheté ce produit. Veuillez lire attentivement ce mode d’emploi et utiliser correcte- ment et de façon sûre le produit. Après lecture, veuillez conserver ce manuel ensemble avec la carte de garantie. Ce produit est la bague d’extension étanche (PER-E01) pour l’utilisation avec un caisson étanche de série PT-E. Il est conçu pour être utilisé en utilisant le modèle de convertisseur arrière “ZUIKO DIGITAL 1.4X TELECONVERTER (EC- 14)” qui peut allonger la distance fo
ملخص المحتوى في الصفحة رقم 20
1 Nomenclature des pièces Corps principal PER-E01 Joint silicone (POL-E101) Bouchon avant Bouchon arrière Monture de caisson étanche de série PT-E Graisse pour joint silicone Pic pour retirer les joints Monture de port d’objectif étanche * Ce produit a été conçu pour un usage exclusif avec le convertisseur arrière suivant. Il ne peut pas être utilisé en combinaison avec un convertisseur arrière autre que le convertisseur suivant. Convertisseur arrière applicable ZUIKO DIGITAL 1
