ملخص المحتوى في الصفحة رقم 1
DC300
Document Camera
USER MANUAL
1
ملخص المحتوى في الصفحة رقم 2
Please read this manual carefully before operating the document camera and keep it for reference. PRECAUTIONS NOTICE: PLEASE READ CAREFULLY BEFORE USE Use the document camera under the rated electric conditions. Do not place the document camera on an unstable surface as it may fall, causing injury or damage. Do not place this device directly under sunlight or near heaters. Do not place this device near water. Keep the camera away from acid or alkali gas. Do not
ملخص المحتوى في الصفحة رقم 3
USER MANUAL .............................................................................1 1. PARTS IDENTIFICATION ..........................................................4 2. CONTROL PANEL .....................................................................5 3. INPUTS AND OUTPUTS............................................................5 4. REMOTE CONTROL..................................................................6 5. CONNECTIONS .................................................
ملخص المحتوى في الصفحة رقم 4
PARTS IDENTIFICATION 7 1. Camera 2. LED Light 3. Flexible Camera Arm 4. IR Receiver for Remote Control 5. Interface Panel (VGA Port, Power Input and USB) 6. Control Panel 7. Kensington Lock 4
ملخص المحتوى في الصفحة رقم 5
CONTROL PANEL 5 2 6 1 4 4 6 3 5 1. POWER: Turn on/off the power. 2. LAMP: Turn on/off the LED light. 3. AUTO: Perform auto focus, color adjustment and white balance. 4. FOCUS+/-: Adjust focus manually. 5. BRIGHT+/-: Image brightness control. 6. ZOOM+/-: Control image zoom in and zoom out. 3. INPUTS AND OUTPUTS 1. DC 12V: Power input. 2. VGA OUT: VGA (RGB) signal output (15 pin D-SUB). 3. USB: Capture image from connected computer with provided software. 5
ملخص المحتوى في الصفحة رقم 6
REMOTE CONTROL 1. Power: Power document camera on and off 2. Video: Video mode 3. Home/Directional Key: Home button 4. Lamp: Turn LED light On/Off 5. Save: Capture the image in display 6. Recall: Image recall mode enabled, display the saved images 7. Auto: Perform auto focus, color adjustment and white balance 8. Split: Split screen enables the comparison between the frozen image and live image 9. Freeze: Freeze/unfreeze the image 6
ملخص المحتوى في الصفحة رقم 7
10. Rotate: Rotate image 11. Sharp+/-: Image sharpness control 12. Computer: Computer mode 13. SXGA/XGA: Switch the output signal between XGA and SXGA 14. Mirror: Output right-and-left, up-and-down mirror image 15. Page +/-: Saved image page up and down when image recall mode is enabled 16. Zoom+/-: Image zoom in and zoom out control 17. Bright+/-: Image brightness control 18. Focus+/-: Adjust focus manually 19. Red+/-: Image chroma control (red) 20. Blue+/-: Image chroma control (blue
ملخص المحتوى في الصفحة رقم 8
5. CONNECTIONS 5.1. COMPUTER CONNECTION 5.2. VGA OUTPUT CONNECTION 8
ملخص المحتوى في الصفحة رقم 9
6. COMMUNICATING WITH COMPUTER 6.1 COMPUTER REQUIREMENTS Minimum PC and software requirements: Operating system: Windows XP CPU: Pentium 4 1.8GHz Physical memory: 512M Video memory: 64M 6.2 USB FUNCTION SOFTWARE INSTALLATION Click “Next” when dialogue box appears to run the software installation package: 9
ملخص المحتوى في الصفحة رقم 10
Read the terms, select "I accept the terms in the license agreement" and click "Next" as shown below: When the following dialogue box appears, click "Next": 10
ملخص المحتوى في الصفحة رقم 11
The default installation directory is Program Files, C: \ Program Files \. Click “Next” to proceed with default installation directory or click “Change” to select a different installation directory: After selecting destination folder, click “OK”. 11
ملخص المحتوى في الصفحة رقم 12
Then click "Next". Click "Install" to complete installation. 12
ملخص المحتوى في الصفحة رقم 13
Click "Finish” to complete the installation. Then you will see the following dialogue box, which is an installation package for 2005 C++ environment. If your PC already has this installed, click "No" to exit. Otherwise, click "Yes" to install it. 13
ملخص المحتوى في الصفحة رقم 14
STARTING SOFTWARE Double click the short cut icon on the desktop to launch the software. IMAGE CAPTURE AND VIDEO RECORDING Left click to capture images. The captured images will be automatically saved into the default destination folder. The path and file name are displayed in software status bar on the bottom of the window as shown below: 14
ملخص المحتوى في الصفحة رقم 15
Left click to start recording. While recording, the settings button will be inactive. Detailed information is displayed on the software status bar at the bottom of the window. The video is automatically saved in the default folder or pre-set folder. SETTINGS The captured images and recorded videos will be saved automatically into the Images and Videos folders. To set a different path for the Image/Video to be saved, click icon on th
ملخص المحتوى في الصفحة رقم 16
the options of recording video with or without sound as shown below: “The length of video that can be recorded” box displays the longest recording time for videos to be saved in the preset path as shown below: Click “save” to complete setting. IMAGE MODIFICATIONS To begin image modifications, click icon. Select Graphic and Move icon allows you to select and move lines, circles, etc to a different position within the image. 16
ملخص المحتوى في الصفحة رقم 17
Line Clicking icon allows you to create lines within the image. icon allows you to change the setting of the chosen line. 17
ملخص المحتوى في الصفحة رقم 18
Line Width: Change the width of the line. X, Y: Change the position of the line. Color: Change the color of the line. Width, Height: Change the angle of the line. Rectangles icon allows you to place a rectangle in the image as shown below. icon allows you to change the setting of the chosen rectangle. 18
ملخص المحتوى في الصفحة رقم 19
Line Width: Change the line width of the rectangle. X, Y: Change the position of the rectangle. Color: Change the line color of the rectangle. Fill Color: Check box to fill color in the rectangle. Width, Height: Change the shape of the rectangle by changing the angle of two adjacent lines of the rectangle. Circular Shapes icon allows you to place circular shapes in the image as shown below. icon allows you to change the setting of the chosen circle. 19
ملخص المحتوى في الصفحة رقم 20
Line Width: Change the line width of the circle. X, Y: Change the position of the circle. Color: Change the line color of the circle. Fill Color: Check box to fill color in the circle. Width, Height: Change the size of the circle. Freeform icon allows you to place scribbles in the image as shown below. icon allows you to change the setting of the chosen curve: 20
