ملخص المحتوى في الصفحة رقم 1
DHSIP
SOURCE INPUT
WALL PLATE
www.atonhome.com
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
DHSIP Source Input Wall Plate Safety Information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener- ates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio comm
ملخص المحتوى في الصفحة رقم 4
DHSIP Source Input Wall Plate Precautions • Always exercise care when operating a system utilizing the DHSIP. • Do not install near any heat sources such as radiators, heat reg isters, stoves, or other apparatus (including amplifiers) that produce heat. • In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power the DH44 or DH46X Digital Audio Router that the DHSIP is connected to off. Please report the problem to your dealer immediatel
ملخص المحتوى في الصفحة رقم 5
DHSIP Source Input Wall Plate 1. Introduction The DHSIP Source Input Wall Plate allows a Local Source (a source located within a room and not avail- able to the DH44 Digital Audio Router system as a whole) to easily connect to a DHTP1 Amplifi ed Touch Pad. It also serves as a source input wall plate for the DH46X Digital Audio Router in stand-alone applica- tions. The DHSIP provides connections for Analog Audio, Digital Optical Audio, Digital Coaxial Audio and IR Control. Features • Local
ملخص المحتوى في الصفحة رقم 6
DHSIP Source Input Wall Plate Front 1 6 5 2 4 3 Figure 1.1: DHSIP Front Callout 4 ©2008 • All rights reserved.
ملخص المحتوى في الصفحة رقم 7
DHSIP Source Input Wall Plate Function Analog Audio Input (L/R) 1 Digital Coaxial Audio Input 2 IR Output 3 Source Input Switch 4 Digital Optical Audio Input 5 Clipping Indicator LED 6 © 2008 • All rights reserved. 5
ملخص المحتوى في الصفحة رقم 8
DHSIP Source Input Wall Plate Rear DHSIP Side View GAIN RL +4+8+4+8 O12 3 4 N 1 2 Figure 1.2: DHSIP Rear Callout Function Gain Adjustment DIP Switches 1 Output RJ-45 Connector 2 6 ©2008 • All rights reserved.
ملخص المحتوى في الصفحة رقم 9
DHSIP Source Input Wall Plate 2. Wiring/Installation Wiring for the DHSIP consists of a single run of Cat-5 wire between the DHTP1 Amplifi ed Touch Pad or DH46X Digital Audio Router and the mounting loca- tion for the DHSIP. Note: Do not run Cat-5 wires closer than 12" from high voltage wires. T-568A Wiring Standard All Cat-5 connections in a DH44-based system use the industry standard T-568A wiring scheme as il- lustrated in Figure 2.1. RJ-45 connectors are used to terminate Cat-5 wires at
ملخص المحتوى في الصفحة رقم 10
DHSIP Source Input Wall Plate Installation The DHSIP is designed to mount in a standard single- gang rough-in box (J Box). Mount the unit in close proximity to the location of the source that will be connected to it. Note: Do not mount the DHSIP in the same rough-in box as high voltage devices such as electrical outlets or switches. After running Cat-5 and terminating the ends, route the wire into the back of the rough-in box, connect it to the RJ-45 connector on the rear of the DHSIP,
ملخص المحتوى في الصفحة رقم 11
DHSIP Source Input Wall Plate 3. Connections Connections for the DHSIP consists of: 1. Source Connections - Front 2. DHTP1 Amplified Touch Pad Connections - Rear 3. DH46X Digital Audio Router - Rear Source Connections Sources are connected to the DHSIP in one of three ways: 1. Analog 2. Digital Coaxial 3. Digital Optical For best sound quality, use one of the Digital connec- tion methods if the Source has this type of output. For sources that do not have Digital outputs, use the Analog opt
ملخص المحتوى في الصفحة رقم 12
DHSIP Source Input Wall Plate Analog (AUDIO IN L/R) Use RCA audio patch cables to connect an audio source that does not have a Digital output as shown in Figure 3.1. DHSIP Front Stereo RCA Patch Cables Audio Source Analog Output L R Figure 3.1: Audio Source to DHSIP Connections Analog Set the RCA/OPT/COAX Selection Switch to the RCA position. 10 ©2008 • All rights reserved.
ملخص المحتوى في الصفحة رقم 13
DHSIP Source Input Wall Plate Digital Optical (OPTICAL IN) Use a Digital Optical Cable to connect an audio source that hase a Digital Optical output as shown in Figure 3.2. Important: See Note 2 & Note 3 on p.9 prior to confi guring Digital Audio connections. DHSIP Front Audio Source Digital Digital Optical Optical Output Cable DIGITAL OPTICAL Figure 3.2: Audio Source to DHSIP Connections Digital Optical Set the RCA/OPT/COAX Selection Switch to the OPT position. © 2008 • All rig
ملخص المحتوى في الصفحة رقم 14
DHSIP Source Input Wall Plate Digital Coaxial (COAX IN) Use a Digital Coaxial Cable to connect an audio source that has a Digital Coaxial output as shown in Figure 3.3. Important: See Note 2 & Note 3 on p.9 prior to confi guring Digital Audio connections. DHSIP Front Audio Source Digital Coaxial Output DIG COAX Digital Coaxial Cable Figure 3.3: Audio Source to DHSIP Connections - Digital Coaxial Set the RCA/OPT/COAX Selection Switch to the COAX position. 12
ملخص المحتوى في الصفحة رقم 15
DHSIP Source Input Wall Plate IR OUT Connect a standard IR Emitter (ATON AIE2, for exam- ple) from the IR OUT port on the front of the DHSIP to the IR receiver on the front of the audio source (see Figure 3.4). For sources that have an IR Input port on the back of the unit, use a 3.5mm to 3.5mm mono interconnect cable instead (see Figure 3.5). DHSIP Front AIE2 Talk-Back Emitter CD Figure 3.4: IR OUT to Local Source - IR Emitter © 2008 • All rights reserved.
ملخص المحتوى في الصفحة رقم 16
DHSIP Source Input Wall Plate DHSIP Front Audio Source 3.5mm Mono IR Input Interconnect Cable IR IN Figure 3.5: IR OUT to Audio Source 3.5mm Interconnect Cable 14 ©2008 • All rights reserved.
ملخص المحتوى في الصفحة رقم 17
DHSIP Source Input Wall Plate Rear Connections DHTP1 Amplifi ed Touch Pad When utilizing the DHSIP as a means to connect a Local Source to a specifi c zone of a DH44-based system, rear connections consists of plugging in a Cat-5 wire terminated to an RJ-45 connector wired to T-568A standard to the RJ-45 jack on the rear of the DHSIP. The other end simply plugs into the LOCAL PORT RJ-45 jack on the rear of the zone’s DHTP1 Amplifi ed Touch Pad. See Figure 3.6 for details. DHSIP DHTP1 Poster
ملخص المحتوى في الصفحة رقم 18
DHSIP Source Input Wall Plate DH46X Digital Audio Router When utilizing the DHSIP as a means to connect an audio source to a DH46X Digital Audio Router in Stand-Alone mode, rear connections consists of plug- ging in a Cat-5 wire terminated to an RJ-45 connector wired to T-568A standard to the RJ-45 jack on the rear of the DHSIP. The other end simply plugs into the SOURCE LOOP IN RJ-45 jack on the rear of the DH46X. See Figure 3.7 for details. DHSIP Side View Cat-5 DH46X Rear Figure 3.7: D
ملخص المحتوى في الصفحة رقم 19
DHSIP Source Input Wall Plate 4. Settings/Adjustment There is one LED on the front of the DHSIP that moni- tors the output level of connected sources. There are two sets of DIP switches on the rear of the unit (marked “GAIN”) designed to adjust the output level of the connected source. Note: The GAIN DIP switches are only for Analog Inputs. The Digital Coaxial and Digital Optical Inputs do not utilize these switches. GAIN RL +4 +4+8 +8 4 O 1 2 3 N Figure 4.1: GAIN DIP Switches © 2008 • Al
ملخص المحتوى في الصفحة رقم 20
DHSIP Source Input Wall Plate Adjusting Analog Audio Source Output Level Once all connections are made, the Analog Audio Source should be adjusted for clipping (distortion) before the DHSIP is mounted in place. To adjust the Analog Audio Source Output Level: 1. Ensure that the Analog Audio Source is connected properly. 2. Power up the source and turn on an audible signal (Press PLAY, tune to a station, etc.). 3. Select the Source from the zone’s DHTP1 Touch- pad. If it is a
