ملخص المحتوى في الصفحة رقم 1
HOME AUTOMATION, INC.
Model 32A30
Touchscreen Hub
Installation Manual
Document Number 32I30-1 Rev B
March, 2008
ملخص المحتوى في الصفحة رقم 2
Copyright © 2005-2008 Home Automation, Inc. All Rights Reserved
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION The HAI Touchscreen Hub is used to provide power, communications, and a video signal to HAI OmniTouch touchscreens. Up to eight (8) OmniTouch touchscreens, with or without video, can be connected; however, you may connect an additional Touchscreen Hub for a total of up to 16 OmniTouch touchscreens when used with an HAI OmniPro II or HAI Lumina Pro controller. The Touchscreen Hub is required for connecting OmniTouch with Video touchscreens. The HAI Touchscreen Hub provid
ملخص المحتوى في الصفحة رقم 4
INSTALLATION NOTE: This unit has protection against static discharge in normal operation. However, use static discharge precautions during installation. Always touch the enclosure to discharge static before touching the connections. NOTE: Do not make changes to terminal lock connections (TB1 – TB6) with power on! Disconnect power AND batteries first. 1. GROUNDING Each Touchscreen Hub MUST be grounded to the controller. The HAI controller and HAI Touchscreen Hub(s) must be g
ملخص المحتوى في الصفحة رقم 5
CAT 5 CONNECTORS OMNITOUCH 5.7 (53A00-1) TERMINATING CAMERA RESISTOR OMNITOUCH WITH VIDEO(32A00-5) INPUT JUMPER TERMINAL BLOCKS CAMERA OUTPUT OMNITOUCH (32A00-1) AA A A GND(GROUND) * ZONE(+) B / GREEN ZONE(-) A / YELLOW CAMERA POWER A = MOUNTING HOLES FOR VIDEO ENCODER 1.5A MAXIMUM HAI CONTROLLER GND MUST BE CONNECTED *TO GND ON HAI CONTROLLER
ملخص المحتوى في الصفحة رقم 6
3. LOW BATTERY INDICATOR (Optional Connection) When the backup batteries connected to the Touchscreen Hub become depleted, there are terminals on the Touchscreen Hub that are used to send a signal to the HAI controller to alert you of the low battery condition. To take advantage of this feature, you must have an extra pair of wire between the Touchscreen Hub and the HAI controller, and an available zone on the HAI controller. Connect the terminals labeled “LB+” and “LB-” under the sec
ملخص المحتوى في الصفحة رقم 7
Connecting to OmniTouch (32A00-1) When connecting a standard OmniTouch to the Touchscreen Hub, it is very important to plan where the OmniTouch touchscreen will be installed and the gauge/type of wire you will use for the installation. The touchscreen requires a minimum of 4 wires for operation (2 for power and 2 for communications). The required distance between the Touchscreen Hub and the touchscreen will determine the wire gauge/type you should use. To prevent the touchscreen from
ملخص المحتوى في الصفحة رقم 8
5. CAMERA CONNECTIONS The Touchscreen Hub takes the composite signal from any NTSC camera, digitizes it through the encoder, and then broadcasts it to the connected OmniTouch with Video or OmniTouch 5.7 touchscreens. The Touchscreen Hub supports 6 individual cameras. In the areas marked CAMERA 1 – CAMERA 6, there is a connector for the camera input (to connect the camera) and the camera output (to connect the video signal to additional devices). Camera Inputs Connect NTSC compo
ملخص المحتوى في الصفحة رقم 9
6. CONNECTING A SECOND HAI TOUCHSCREEN HUB When connecting more than 8 OmniTouch with Video touchscreens to an HAI OmniPro II or HAI Lumina Pro controller, a second Touchscreen Hub is required. To view video on the additional OmniTouch with Video touchscreens (the ones connected to the second Touchscreen Hub), a Video Encoder installed on the second Touchscreen Hub is required. When connecting a second Touchscreen Hub, with the exception of cameras, make all other connections as desc
ملخص المحتوى في الصفحة رقم 10
32A32-2 VIDEO ENCODER NYLON SPACER 32A30-1, -2, -3, -4 TOUCHSCREEN HUB
ملخص المحتوى في الصفحة رقم 11
8. POWER CONNECTIONS The supplied Power Pack provides both touchscreen (24VDC) and camera (12VDC) power. An AC power outlet should be located within 5 feet. One or two sealed, rechargeable batteries (not included) can be used to backup the touchscreen and camera (optional) power. The two battery cables are in parallel, so by adding a second battery you will increase the battery backup time. 1. Connect one or two 12VDC batteries using the supplied battery terminals. Connect the BL
ملخص المحتوى في الصفحة رقم 12
SPECIFICATIONS Operating 32 - 120 degrees F (0 - 49 degrees C) Ranges: 10 - 85 % relative humidity, non-condensing Power Pack: Output 19VDC, 3.79 Amps, Max 72W Input 120VAC, 1.8A amps, 60Hz Maximum Power: 72 Watts Batteries: Sealed, Rechargeable, 12 volts, 4 - 8 amp-hours each Low Voltage Cut Out: 10VDC Main Fuse: 5A Polyfuse Battery Fuses: 5A Polyfuse Polyfuses are permanent fuses that do not need replacement. Camera Power: Nominal Voltage
