ملخص المحتوى في الصفحة رقم 1
CAT5 SWITCHER
KE811CT(w-type)
Instruction Manual
Please be sure to read this manual completely prior to usage of this product.
ملخص المحتوى في الصفحة رقم 2
RGB Interface Cable Use of a RGB interface cable longer than 3 m (9.84 feet) is not recommended. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
ملخص المحتوى في الصفحة رقم 3
Please be sure to read this manual prior to usage of product. After reading, keep it in a place near the equipment where it can be easily referred to. If this symbol is ignored death or serious injury may occur. If this symbol is ignored injury or property damage may occur. Shows caution Shows an action that should be done. (including warning) General caution Keep hands clear General indication Unplug the power cord Shows an actio
ملخص المحتوى في الصفحة رقم 4
Do not continue to use this product if any of the following occurs : It may cause fire or electric shock. If you smell a strange odor or smoke. If water or a foreign object gets inside the product. After dropping the product. If the power cord is damaged. (exposure of core cable, severed cable) If any of the above should occur immediately turn the power off and unplug the power cord. Contact the manufacturer or dealer who installed this product for repair
ملخص المحتوى في الصفحة رقم 5
Do not put this product in the following places. May cause fire or electric shock. Places where there is a lot of humidity or dust. Places where there is steam. Near places which generate heat. Places where water may come into contact with the product. Turn off the power and follow all instructions , when connecting this product to other devices. Failure to use the recommended cables may cause generation of heat or fire. Do not cover the ventilation hole
ملخص المحتوى في الصفحة رقم 6
1. About this product 1-1. Product and accessories 1-2. General information 2. Th nam and uncti n ach parts 2-1. Front panel 2-2. Rear panel 3. Connection 3-1. The cautions and warnings 3-2. Preparation of a cable 3-3. Cable mounting kit and rack mounting kit 3-4. How to connect 4. Operation 4-1. The setting of front dip switch 4-2. The setting of bottom dip switch 4-3. Operation of buttons 5. Serial interface 5-1. The setting of personal computer 5-2. Connecti
ملخص المحتوى في الصفحة رقم 7
1.About this product (KE811CT(w-type)) 1-1. Product and accessories Please check that you have the accesories and items shown. KE811CT Main unit of KE811CT(w-type) AC adapter Cable mounting kit Power cord Rack mounting kit 2 Screw 4 Screw 4 Fixing bands 2 Terminal 6-pin 2 Terminal 2-pin 2 CAT5 SWITCHER KE811CT(w-type) Instruction Manual Thank you for your purchase of this product Please be sure
ملخص المحتوى في الصفحة رقم 8
1-2 General Information This product, KE811CT(w-type), is a transmitter for long distance transmission of one line selected from RGB video, component video or composite video through a twisted pair cable (CAT5e or CAT6). In addition to video , one line of audio (stereo) , and serial command (*1) can be transmitted through a serial port. By INPUT switch, it is possible to control PDP or projector at the same time as switching of video and audio . (*1) Beforehand registered serial command
ملخص المحتوى في الصفحة رقم 9
2 The name and function of each parts 2-1. Front panel KE811CT POWER CONT button This button controls external power. When this button is pushed,the signal (photo MOS relay make contact)is output from connector for POWER CONT. (This button is not for the product.) This button can be synchronized DISPLAY POWER button. At synchronization mode, DISPLAY POWER butt
ملخص المحتوى في الصفحة رقم 10
CAT5_OUT button CAT5 output is selected. Front Dip Switch Please refer to "4-1. The setting of front dip switch." SERIAL_3 DB9 connector for serial communication. This connector is used to register commands into the product. (Please refer to "5-2 Connection of RS232C cable.") Front LED Yellow LED : It does not light. Green LED : It lights when command mode is ON. Orange LED : It lights when SERIAL1&3 are transmitting or receiving. Bottom dip swit
ملخص المحتوى في الصفحة رقم 11
CONT 2-2 Rear panel SERIAL 1 SERIAL 2 3 4 1 2 5 6 7 AUDIO IN AUDIO SUB OUT CAT5 OUT1 CAT5 OUT2 PARALLEL REMOTE FG DC16V IN 2 3 5 6 7 4 1 POWER OPTION OUT COMPOSITE COMPOSITE IN RGB IN COMPONENT IN RGB SUB OUT A B C D E F SUB OUT COMPOSITE IN 1-3 RCA connector, video input connectors. Input connectors for composite video. These connectors are corresponding to INPUT 1-3 at front panel. Please use a cable under 3m(9.84feet) in length when connecti
ملخص المحتوى في الصفحة رقم 12
DC16V_IN Connecter for power input. DC16V AC adapter is connected. Warning The enclosed AC adapter must be used for this product. FG The screw for frame ground. AUDIO IN 1-4 RCA connector for audio input connector. These connectors are audio input connector. These connectors are corresponding to INPUT 1-4 at front panel. Please use a cable under 3m(9.84feet) in length when connecting. AUDIO IN 5-8 Mini-jack for audio
ملخص المحتوى في الصفحة رقم 13
3 Connection 3-1 The cautions and warnings Cautions Use the recommended a twisted-pair cable for this product for best results. (OKANO ELECTRIC WIRE CO.,LTD: OKTP-E5-P-AWG 24x4P) When a cable other than the recommended cable is used, make sure that the characterisitcs and functionality of the cable is fully understood before use. When cable length is longer than the recommendation distance indicated in the "1-2 General information", quality of
ملخص المحتوى في الصفحة رقم 14
3-2.Preparation of a cable A CAT5e or CAT6 cable is used to connect this product and twisted pair receiver. This product and receiver are connected straight through as shown in the diagram below. Please keep the combination of the pair lines as follows. If the combination of a pair line is incorrectly installed , there is a possibility that the quality of the image may deteriorate. pair 1 Cables pair 2 Connector Connector pair 3
ملخص المحتوى في الصفحة رقم 15
3-3. Cable mounting kit and rack mounting kit A mounting kit for the twisted-pair cable is enclosed with this product. Use the following diagram to attach the mounting kit. Diagram for attachment Cable mounting kit Cable mounting kit Cable mounting kit
ملخص المحتوى في الصفحة رقم 16
CONT 3-4. How to connect Connect this product according to the following procedures. Check that all of the devices ,PDP(Plasma Display Panel), video player, DVD player, PC, display, and so on, to connect are turned off. Refer to the following diagrams when connecting cables to this product. KE811CT SERIAL 1 SERIAL 2 2 3 4 1 5 6 7 AUDIO IN AUDIO SUB OUT
ملخص المحتوى في الصفحة رقم 17
Audio 3 4 5 6 7 8 1 2 AUDIO IN AUDIO SUB OUT As for connection of cables going to twisted pair receiver, please refer to the manual of twisted pair receiver. Connect between this product and twisted pair receiver by using CAT5e or CAT6 cable. (Please refer to "3-2 Preparation of ca
ملخص المحتوى في الصفحة رقم 18
4. Operation 4-1. The setting of front dip switch NO. 1 ON Registration mode (Regardless of the setting of No.2-4.) OFF Standard mode 2 no working 3 ON POWER CONT becomes ON, when AC adapter is connected to outlet. OFF POWER CONT becomes ON, when POWER CONT is pressed. 4 no working All switches of front dip switch are set at OFF as initial setting.
ملخص المحتوى في الصفحة رقم 19
4-2. The setting of bottom dip switch NO. 1 ON OPTION A button, momentary OFF OPTION A button, alternate 2 ON OPTION B button, momentary OFF OPTION B button, alternate 3 ON OPTION C button, momentary OFF OPTION C button, alternate 4 ON OPTION D button, momentary OFF OPTION D button, alternate 5 ON OPTION E button, momentary OFF OPTION E button, alternate 6 ON OPTION F but
ملخص المحتوى في الصفحة رقم 20
4-3. Operation of buttons a) POWER CONT button It can control the power in the rack. The operation of others buttons can be controlled (become ON), when this button is pressed. When NO.7 of bottom dip switch is ON, DISPLAY POWER button synchronizes and becomes ON. (Please refer to "4-2. The setting of bottom dip switch.") When POWER CONT button is OFF, all buttons are OFF (It is not related to a setup of a switch). This button is n
