ملخص المحتوى في الصفحة رقم 1
HCCA-D1200
HCCA-D1200
HCCA-D2400
HCCA-D2400
HCCA-D5000
HCCA-D5000
ملخص المحتوى في الصفحة رقم 2
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION Thank you for your purchase of Orion's HCCA-D1200, HCCA-D2400, or HCCA-D5000 power amplifier. Each Orion amplifier is designed to be the leader in its class offering the most power, advanced features, and extreme ease of use. In high-end sound systems or high SPL systems, Orion amplifiers will give you years of trouble-free performance. ● HCCA-D1200 - 1200 Watt single-channel Class D amplifier with built-in infrason- ic filter, with INTELLi-Q, ESP2, and remote bass. The HCCA-D1200 i
ملخص المحتوى في الصفحة رقم 4
PRACTICE SAFE SOUND™ Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High power automotive sound systems can generate sound pressure levels in excess of 130dB. When playing your system at high levels, please use hearing protection and avoid long term exposure. RECORD YOUR SERIAL NUMBER AND DATE To ensure your warranty (see back cover), please record the following information regard- ing your new amplifier. Model: _________________________________________
ملخص المحتوى في الصفحة رقم 5
10. Phase Control Switch - provides either 0 or 180 degree phase shift of the ampli- fied output (speaker) with respect to the input signal to facilitate bridging of amplifiers. 11. Power LED - when illuminated (green) indicates that the amplifier is on. Protect LED - when illuminated (red) indicates that the amplifier protective cir- cuitry has been activated due to thermal, output short, supply undervoltage or supply overvoltage. ® ® ESP Indicator LED - when illuminated (yellow) indicates ESP
ملخص المحتوى في الصفحة رقم 6
2. +BAT - connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio sys- tem battery. WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 3. REM - this terminal turns on the amplifier when (+) 12 volt is applied. Connect it to the remote turn on lead of the head unit or signal source. If a (+) 12 volt
ملخص المحتوى في الصفحة رقم 7
SPECIFICATIONS Amplifier Section HCCA-D1200 HCCA-D2400 HCCA-D5000 Power Output 4W 250 x 1 450 x 1 1000 x 1 (Watts) 1 Power Output 2W 400 x 1 800 x 1 1600 x 1 (Watts) 2 Power Output 1W 600 x 1 1200 x 1 2500 x 1 (Watts) Amplifier > 70% into 1W load > 70% into 1W load > 70% into 1W load Efficiency at max. power at max. power at max. power Externally yes yes yes Bridgeable Remote Bass yes (HP-RB1 yes (HP-RB1 yes (HP-RB1 Function supplied) supplied) supplied) Distortion at < 1.0% THD+N < 1.0% THD
ملخص المحتوى في الصفحة رقم 8
AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, infrasonic switch, gain controls, high pass and low pass crossovers controls, Intelli-Q control, and RCA inputs. The input section makes it easy to adapt this amplifier to most sys- tem configurations. Input Gain These Orion amplifiers have level adjustments to allow for easy integration with any source unit. The input sensitivity can be ad
ملخص المحتوى في الصفحة رقم 9
WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range. This can cause driver failure that is not covered by the man- ufacturer's warranty. Low-Pass Crossover When the switch is to the left (OFF position), the low-pass crossover is bypassed. When the switch is in the middle (12 position), the low-pass crossover is active with a 2nd order (12dB per octave) slope. When the switch is to the right (24 position), the low-pass crossover is active with a 4th orde
ملخص المحتوى في الصفحة رقم 10
Enclosure Type Boost Levels 0dB +3dB +6dB +10dB Infinite Baffle Tune above High X-Max Not Not Fs of woofer Drivers--Tune Recommended Recommended above Fs of woofer Sealed Tune above Tune above High X-Max Not Fs of woofer Fs of woofer Drivers--Tune Recommended above Fs of woofer Vented Tune to port Tune to port Tune to port High X-Max frequency frequency frequency Drivers--Tune to port frequency Sealed Band-pass Tune above Tune above High X-Max Not Fs of woofer Fs of woofer Drivers--Tune
ملخص المحتوى في الصفحة رقم 11
Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz. Up to 6 dB of boost is capable at this frequency. With +6dB of boost, the woofer has more output down to 23 Hz. The overall usable output is increased. Vented Example H
ملخص المحتوى في الصفحة رقم 12
Remote Gain Operation NOTE: Do not use the Remote Gain control when you have an expanded system installed (see Line Ouput Configurations). The Slave amplifier(s) gain will not be controlled. The remote gain port provides easy remote access to the internal gain structure of the HCCA power amplifier. The HP-RB1 plugs into the amplifier via the 1/8" mini jack plug. The HP-RB1 can be installed in the front of the vehicle to control the amplifier gain level. The HP-RB1 can be used as a bass level con
ملخص المحتوى في الصفحة رقم 13
Speaker Connections The Orion HCCA-D1200, HCCA-D2400, and HCCA-D5000 amplifiers offer two positive and two negative output terminals for ease of connecting the speakers to the amplifier. Since these are mono amplifiers, the speaker connectors are paralleled internally. Each amplifier is stable to 1W. See diagrams below. MASTER SLAVE Bridging For bridging into a single speaker load, the Orion HCCA-D1200 and HCCA-D2400 have the ability to be bridged with another amplifier of the
ملخص المحتوى في الصفحة رقم 14
MASTER AMPLIFIER SLAVE AMPLIFIER PHASE PHASE MASTER SLAVE 0 ° 180° MASTER SLAVE 0 ° 180° AMPLIFIER INSTALLATION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance. Always mount the amplifier in a place that pro
ملخص المحتوى في الصفحة رقم 15
General Precautions and Installation Tips WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle. Disconnect the vehicle's ground wire at the battery before making or breaking connections to the audio system's power supply terminals. Do not use this amplifier unmounted. Failing to securely mount the amplifier can result in damage or injury, particularly in the event of an accident. An unmou
ملخص المحتوى في الصفحة رقم 16
● RTA (real time analyzer) ● Soldering iron and solder ● Utility knife ● Wire brush or sandpaper for chassis grounding ● Wire crimper ● Wire cutters ● Wire strippers Step By Step Installation Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information. Step 2 Decide on the system configuration for your amplifier. For system sugges- tions, refer to the Speaker Connections section of this guide. Step 3 Run all the wires f
ملخص المحتوى في الصفحة رقم 17
SET UP AND TROUBLESHOOTING Testing the System After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system. Step 1 Check all the wiring connections to be sure they are correct and secure. Step 2 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control. Ste
ملخص المحتوى في الصفحة رقم 18
Step 6 Turn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output. Depending on your system the midrange and tweeter output may be on the same output channels. Step 7 Fine-tune the output level between midrange and tweeters. Refer to the Internal Crossover Configuration section of this manual for detailed instruc- tions. Step 8 Repeat Steps 5-7 for the rear speakers. If you do not have rear spe
ملخص المحتوى في الصفحة رقم 19
Troubleshooting Tips Symptom Probable Cause Action To Take No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and repair or replace as needed. Audio input not connected Check RCA connections and repair or replace as needed. Speaker wires not Check speaker wires and re
ملخص المحتوى في الصفحة رقم 20
Symptom Probable Cause Action To Take Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed. Poor bass response Speakers wired with wrong Check speaker polarity and fix polarity causing cancellation as needed. at low frequencies Crossover set incorrectly Reset crossovers. Refer
