ملخص المحتوى في الصفحة رقم 1
IEEE 802.3af
Power over Ethernet Injector
POE-151
User’s Manual
- 1 -
ملخص المحتوى في الصفحة رقم 2
Trademarks Copyright Ó PLANET Technology Corp. 2006. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS 1. INTRODUCTION.......................................................................................................................................... 4 1.1 CHECKLIST ................................................................................................................................................ 4 1.2 ABOUT THE POWER OVER ETHERNET INJECTOR .......................................................................................... 4 1.3 FEATURES .........
ملخص المحتوى في الصفحة رقم 4
1. INTRODUCTION 1.1 Checklist Thank you for purchasing our POE-151 IEEE 802.3af Power over Ethernet Injector, your Power over Ethernet Injector package shall contains following contents: Check the contents of your package for following parts: Power over Ethernet Injector x1 User' s manual CD x1 Power Adapter x1 Power cord x 1 If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing
ملخص المحتوى في الصفحة رقم 5
1.4 Specification Model POE-151 Ethernet Connector 2 x RJ-45( 1 for data + DC in, 1 for Data out) Ethernet Data rate 10/100Mbps( vary on Ethernet device attached) Input voltage DC 48V, 0.4A Number of device can be powered 1 Ethernet cable TIA/EIA-568, Category 5/5e cable LED indicator 1 x power, 1 x POE ready / in-use Dimension (W x D x H) 73 x 55 x 24 mm EMI FCC Class B, CE mark Standard Compliance IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet, IEEE 802.3af Power over Ethernet.
ملخص المحتوى في الصفحة رقم 6
2. HARDWARE INSTALLATION This product provides two different running speeds – 10Mbps, 100Mbps in the same device and automatically distin- guishes the speed of incoming connection. This section describes the hardware features of POE-151. Before connecting any network device to the POE-151, read this chapter carefully. 2.1 Before Installation Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need to power on, the POE-151
ملخص المحتوى في الصفحة رقم 7
2.2 POE-151, the Injector installation 1. Connect a standard network cable from Switch/workstation to “Ethernet” port of POE-151. 2. Connect the long cable that will be used to connect to the remote device to the port “Ethernet + DC”. The screen in Figure 1 appears. 3. Connect the AC adapter to “DC 48V” of POE-151. The power LED will be steady on. Figure 1: the Injector installation 2.3 POE-151 and POE-151S, the IEEE 802.3af Injector and Splitter installation 1. Connect a standard net
ملخص المحتوى في الصفحة رقم 8
Figure 3: Connection architecture over POE-151/151S Notice: 1. According to IEEE 802.3af standard, the POE-151 will not inject power to the cable if not connecting to IEEE 802.3af devices. 2. Please ensure the output voltage is correct before applying power to remote device. 2.4 Connect with IEEE 802.3af devices Due to the capability of IEEE 802.3af standard, the POE-151 can directly connect with any IEEE 802.3af end-nodes like wireless access point, VoIP phones and Inter
ملخص المحتوى في الصفحة رقم 9
3.TROUBLESHOOTING This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the Ethernet Switch was set up according to instructions in this manual. The PoE LED is not lit Solution: Check the cable connection between POE-151 and IEEE 802.3af device. Can the POE-151 work with Gigabit Ethernet device? Solution: The POE-151 use 4-wire for data transmission (pair 1, 2, pair 3, 6) and 4-wire for power supply (pair 4, 5, pair 7, 8),
ملخص المحتوى في الصفحة رقم 10
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments RJ-45 Connector pin assignment MDI MDI-X Contact Media Dependant In- Media Dependant In- terface terface -Cross 1 TX + (transmit) Rx + (receive) 2 TX - (transmit) Rx - (receive) 3 Rx + (receive) TX + (transmit) 4, 5 DC current* 6 Rx - (receive) TX - (transmit) 7, 8 Ground Remark: Gigabit Ethernet is not allowed to use POE-151 since pair 4,5 and pair 7, 8 are all being used for data transmission in Gigabit Ethe
