ملخص المحتوى في الصفحة رقم 1
IEEE 802.3af
Power over Ethernet Splitter
POE-152S-5V/12V
User’s Manual
- 1 -
ملخص المحتوى في الصفحة رقم 2
Trademarks Copyright Ó PLANET Technology Corp. 2006. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS 1. INTRODUCTION.......................................................................................................................................... 4 1.1 CHECKLIST ................................................................................................................................................ 4 1.2 ABOUT THE POWER OVER ETHERNET SPLITTER .......................................................................................... 4 1.3 FEATURES .........
ملخص المحتوى في الصفحة رقم 4
1. INTRODUCTION 1.1 Checklist Thank you for purchasing our POE-152S IEEE 802.3af Power over Ethernet Splitter, your Power over Ethernet Splitter package shall contain following contents: Check the contents of your package for following parts: Power over Ethernet Splitter x 1 User' s manual CD x 1 DC Plug Cable x 2 15cm UTP straight network cable x 1 If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including
ملخص المحتوى في الصفحة رقم 5
1.4 Specification Model POE-152S Ethernet Connector 2 x RJ-45 (1 for Data + DC in, 1 for Data out) Ethernet Data Rate 10/100/1000Mbps (vary on Ethernet device attached) Output Voltage/Current Vary on model: POE-152S-5V: 5VDC, 2.5A max. POE-152S-12V: 12VDC, 1A max. Number of Device can be powered 1 Ethernet Cable TIA/EIA-568, Category 5/5e/6 cable LED indicator 1 x POE ready/in-use Operating environment 0~50 Degree C, 5%~90%RH Storage environment -20~70 Degree C, 5%~90%RH Dimension
ملخص المحتوى في الصفحة رقم 6
2. HARDWARE INSTALLATION These products provide three different running speeds – 10Mbps, 100Mbps,1000Mbps. in the same device and auto- matically distinguish the speed of incoming connection. This section describes the hardware features of POE-152S. Before connecting any network device to the POE-152S, read this chapter carefully. 2.1 Before Installation Before your installation, it is recommended checking your network environment. If there is any issue for your install a networked devi
ملخص المحتوى في الصفحة رقم 7
2.2 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter installation 1. Connect a standard network cable from “Ethernet+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE LED of POE-152 / POE-152S will light on continuance. The screen in Figure 1 appears. From POE-152 or IEEE 802.3af Power Supply equipment Figure 1: Connection to POE-152 or IEEE 802.3af POE equipment 2. Connect the UTP cable in the package from “Ethernet” of POE-152S to the RJ-4
ملخص المحتوى في الصفحة رقم 8
2.3 Connect with IEEE 802.3af devices The POE-152S can also provide the alternative to make the non- IEEE 802.3af devices the possibility to connect with an IEEE 802.3af in-line power device like Power over Ethernet Switch, then connect proper DC plug from "DC OUT" of POE-152S to remote device. The screen in Figure 3 appears. Figure 3: Connect to IEEE 802.3af device Once POE-152S detects the existence of an IEEE 802.3af device, t
ملخص المحتوى في الصفحة رقم 9
3.TROUBLESHOOTING This chapter contains information to help you solve issues. If the POE-152S is not functioning properly, make sure the POE-152S was set up according to instructions in this manual. The PoE LED is not lit Solution: Check the cable connection between POE-152S and IEEE 802.3af device. Why the device connected to POE-152S cannot be powered? Solution: 1. Please check the POE-152S is connect with an IEEE 802.3af complied in-line device like POE-152, and check if the POE
ملخص المحتوى في الصفحة رقم 10
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI MDI-X Contact Media Dependant Media Dependant Interface Interface -Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 Not
ملخص المحتوى في الصفحة رقم 11
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network. 2080-A31120-001
