ملخص المحتوى في الصفحة رقم 1
AMP CONTROL UNIT
NETWORK HUB and BRIDGE
Owner’s Manual
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
NETWORK HUB AND BRIDGE
LINK CONDUCT
LOCK ERROR
88
M
ESPAÑOL DEUTSCH FRANÇAIS ENGLISH
ملخص المحتوى في الصفحة رقم 2
ACU16-C/NHB32-C Owner’s Manual Addendum Please make the following changes and additions to the ACU16-C/NHB32-C owner’s manual. Some of these are due to the ACU16-C/NHB32-C system software upgrade, while others are corrections and supplementary explanations. Changes due to the software upgrade ❏ Support for CobraNet “Low Latency” (system software v1.10) In conjunction with the upgrade to system software V1.10, the latency setting that had been fixed at 5.33 ms can now be selected from three cho
ملخص المحتوى في الصفحة رقم 3
❏ “Installing Acrobat Reader” (page 12) Incorrect—To view the Network Amp Manager Owner’s Manual, you’ll need to install the Adobe Acrobat Reader software, which is included on the CD-ROM. If you already have this software installed, skip this section. Correct—To view the NetworkAmp Manager Owner’s Manual (PDF format), Adobe Reader software (free of charge) must be installed. If you don’t have Adobe Reader, please download it from the Adobe Corporation’s website. http://www.adobe.com ❏ “PRIMAR
ملخص المحتوى في الصفحة رقم 4
ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 4:38 PM / Notes on rack-mounting the unit E If you install the ACU16-C/NHB32-C along with another If the temperature inside the rack is expected to be 40°C or ACU16-C/NHB32-C or other device in a rack that is not well higher (in this case, the room temperature is generally about ventilated, the temperature inside the rack may rise due to the 30°C or higher), install the fan kit on the top shelf of the rack, heat
ملخص المحتوى في الصفحة رقم 5
ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 10:04 AM / Important Note for PC-N Series Power Remarque importante à l’attention Amplifier Users des utilisateurs d’un amplificateur de puissance de la série PC-N When you are using the ACU16-C connected to a PC9500N or PC4800N power amplifier, the NetworkAmp Manager's meter Quand l’ACU16-C est branché à un amplificateur de puissance may not display the correct value, depending on your power PC9500N ou PC4800N, il se peut (selon l’
ملخص المحتوى في الصفحة رقم 6
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructio
ملخص المحتوى في الصفحة رقم 7
Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to CAUTION alert the user to the presence of uninsulated RISK OF ELECTRIC SHOCK “dangerous voltage” within the product’s DO NOT OPEN enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral CAUTION: TO REDUCE THE RISK OF triangle is intended to alert the user to the ELECTRIC SHOCK, DO
ملخص المحتوى في الصفحة رقم 8
4 Software Licensing Agreement The following is a legal agreement between you, the end user, and Yamaha Corporation (“Yamaha”). The enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms set forth herein. Please read this licensing agreement with care. Opening this package indicates that you accept all terms outlined herein. If you do not agree to the terms, return this package unopened to Yamaha for a full refund. GRANT OF
ملخص المحتوى في الصفحة رقم 9
5 Precautions Warnings Installation •Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Man- ual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. •Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. •Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire and electrical shock hazard. In particular, be careful
ملخص المحتوى في الصفحة رقم 10
6 Cautions Installation •Keep this unit away from the following locations: —Locations exposed to oil splashes or steam, such as near cooking stoves, humidifiers, etc. —Unstable surfaces, such as a wobbly table or slope. —Locations exposed to excessive heat, such as inside a car with all the windows closed, or places that receive direct sunlight. —Locations subject to excessive humidity or dust accumulation. •Hold the power cord plug when disconnecting it from an AC outlet. Never pu
ملخص المحتوى في الصفحة رقم 11
7 Important Information Operating Notes •The performance of components with moving contacts, such switches, rotary controls, fad- ers, and connectors, deteriorates over time. The rate of deterioration depends on the oper- ating environment and is unavoidable. Consult your dealer about replacing defective components. •Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit. •The digital circuits of this unit may induce a slight no
ملخص المحتوى في الصفحة رقم 12
8 Trademarks Adobe, Acrobat, and Reader are registered trademarks of Adobe Systems Incorporated. CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc. Ethernet is a trademark of Xerox Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation, Inc. Yamaha is a trademark of Yamaha Corporation. All other trademarks are the property of their respective holders and are hereb
ملخص المحتوى في الصفحة رقم 13
9 Contents 1 NetworkAmp Manager Installation . . . . . . . . . . . 10 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CD-ROM Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ACU16-C/NHB32-C Hookup . . . . . . . . .
ملخص المحتوى في الصفحة رقم 14
10 NetworkAmp Manager Installation 1 NetworkAmp Manager Installation Introduction This chapter explains how to install NetworkAmp Manager and the necessary drivers. For information on how to use NetworkAmp Manager, refer to the Network Amp Manager Owner’s Manual, which is included on the CD-ROM in PDF format and can be opened directly from NetworkAmp Manager’s Help menu. CD-ROM Contents Folder Software Description Adobe Acrobat Reader softw
ملخص المحتوى في الصفحة رقم 15
ACU16-C/NHB32-C Hookup 11 ACU16-C/NHB32-C Hookup The following illustration shows the hookup methods that can be used to connect the ACU16-C/NHB32-C to your computer: USB or serial. 1. USB NETWORK HUB AND BRIDGE LINK CONDUCT LOCK ERROR 88 NHB32-C ACU16-C USB port USB port USB cable 2. Serial - NHB32-C Windows PC running NetworkAmp Manager ACU16-C TO COMPUTER port Serial cable Serial port (9-pin D-sub) (RS-232C) Note: Before you connect to serial ports, turn off the ACU16-C/NHB32-C and
ملخص المحتوى في الصفحة رقم 16
12 NetworkAmp Manager Installation Installing Acrobat Reader To view the Network Amp Manager Owner’s Manual, you’ll need to install the Adobe Acro- bat Reader software, which is included on the CD-ROM. If you already have this software installed, skip this section. 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 On the CD-ROM, double-click the “Acroread_” folder. This folder contains Acrobat software in several langu
ملخص المحتوى في الصفحة رقم 17
Installing the USB MIDI Driver 13 Windows 98 & 98SE 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. 3 Turn on the ACU16-C/NHB32-C. The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon- necting the USB cable. Alternatively, open the Add New Hardware control panel. 4 Click
ملخص المحتوى في الصفحة رقم 18
14 NetworkAmp Manager Installation 5 Select “Search for the best driver for your device (Recommended),” and then click Next. The following window appears. 6 Select “Specify a location,” and specify “D:\USBdrv_” (replacing “D” with the drive letter of your CD-ROM drive), and then click Next. When the driver is located, “YAMAHA USB MIDI Driver” is displayed, as shown below. 7 Click Next. Note: You may be prompted to insert your Windows CD-ROM. Do not insert it! Click OK, and in the “Copy files f
ملخص المحتوى في الصفحة رقم 19
Installing the USB MIDI Driver 15 Windows Me 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. 3 Turn on the ACU16-C/NHB32-C. The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon- necting the USB cable. Alternatively, open the Add New Hardware control panel. 4 Select “Automatic sear
ملخص المحتوى في الصفحة رقم 20
16 NetworkAmp Manager Installation Windows 2000 1 Start your computer and Windows, log on as the Administrator, and then insert the included CD-ROM into your computer’s CD-ROM drive. 2 Go to My Computer–>Control Panel–>System–>Hardware–>Driver Sign- ing–>File Signature Verification, select “Ignore—Install all files, regardless of file signature,” and then click OK. 3 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. 4
