ملخص المحتوى في الصفحة رقم 1
CLK
H-CDM8010
PWR AF
BAND
SEL MODE
50Wx4
H-CDM8010
1 PAU 2 INT 3 RPT 4 RDM 5 DN10 6 UP10
PTY TA
F/PS
CD/MP3-RECEIVER CD/MP3-
Instruction manual
ملخص المحتوى في الصفحة رقم 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. The unit is recommended for installation in cars by Hyundai, Kia, as well as other cars equipped with installation place for 1 DIN head units. Table of contents Table of contents.............................................................................................
ملخص المحتوى في الصفحة رقم 3
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. Before using please heat up the passenger compartment to the recommended temperature! Read carefully through this manual to familiarize yourself with this high-quality system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may c
ملخص المحتوى في الصفحة رقم 4
Accessories 1. Nut 5 mm 1 pc. 2. Spring washer 2 pcs. 3. Screw M5x25 mm 1 pc. 4. Screw 1 pc. 5. Plain washer 2 pcs. 6. Strap 1 pc. 7. Operating instructions 1 pc. 8. Key 2 pcs. 9. Mounting collar 1 pc. 10. Wire connector 1 pc. 11. Trim plate 1 pc. 12. Warranty card 1 pc. 13. Customer information 1 pc. 14. ISO connector 1 pc. 4
ملخص المحتوى في الصفحة رقم 5
Installation/Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installation 1. Remove the old unit from the dashboard. Remove the outer trim frame. Insert the keys supplied with the old unit into both sides of the
ملخص المحتوى في الصفحة رقم 6
Take a length of masking tape and fold it around the wire so it forms a flag. On the masking tape mark the polarity of the speaker wires (+ and -), as well as left or right, and front or rear. Repeat this procedure for all of the speakers. Mark the power, ground, and any other wires also. 6
ملخص المحتوى في الصفحة رقم 7
Installation method A WARNING: Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. 1. After removing the old unit and mounting sleeve, insert supplied mounting sleeve in the opening. 2. Bend the tabs on the mounting sleeve to keep the mounting sleeve firmly in place. 3. Attach wires from the unit to existing wires. See wiring connections diagram. Insert the unit into dashboard. Then apply the trim frame to
ملخص المحتوى في الصفحة رقم 8
Installation method B Note: Outer trim frame, hook, and mounting sleeve are not used for this installation. This is only intended as a general guide; contact the vehicle's manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. 1. Remove the hooks on both sides. 2. Align the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit. Tighten the 2
ملخص المحتوى في الصفحة رقم 9
Electrical connections Speaker Wiring Notes Follow the above wiring diagram to install the head unit with new or existing speakers. This unit is designed for use with four (4) speakers with the impedance between 4 Ohms to 8 Ohms. An impedance load of less than 4 Ohms could damage the unit. Never bridge or combine the speaker wire outputs. When not using four speakers, use electrical tape to tape the ends of the unused speaker outputs to prevent a short circuit. Never ground the negative spea
ملخص المحتوى في الصفحة رقم 10
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector; connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections. Function Location Connector A Connector B 1 Rea
ملخص المحتوى في الصفحة رقم 11
Panel controls Front panel 1. PWR button 2. AF button 3. Disc slot 4. LCD display 5. BAND button 6. EJECT button 7. CLK button 8. PTY button 9. SEL knob 10. TA button 11. 1/PAU button 12. 2/INT button 13. 3/RPT button 14. 4/RDM button 15. 5/DN10 button 16. 6/UP10 button 17. F/PS button 18. MODE button 19. PREV button 20. NEXT button 11
ملخص المحتوى في الصفحة رقم 12
General operations Turning On/Off Press any button to turn the unit on, the display will show a message “WELCOME” to indicate it is ready to use. Press and hold PWR button to turn the unit off. Mode selection Press MODE button to switch between Radio and CD play mode. Volume control The volume level can be adjusted by rotating SEL knob in any mode. LOUD mode Press and hold SEL knob till the display shows “TA SEEK”, then press SEL knob till “LOUD OFF” is shown. Rotate SEL knob to switch between L
ملخص المحتوى في الصفحة رقم 13
BEEP function Press and hold SEL knob for 2 seconds; the display will show “TA SEEK”. Press SEL knob repeatedly until the display shows “BEEP OFF”, rotate SEL knob to toggle between BEEP ON and BEEP OFF, then leave the unit idle for your desired setting to take effect. Clock setting The clock can be set anytime when the power is on. Press CLK button and then press and hold CLK button for 3 seconds, the time will blink on the display. 1. Rotate SEL knob clockwise to adjust the hour. 2. Rotate SEL
ملخص المحتوى في الصفحة رقم 14
You can rotate SEL knob to switch to “VOL ADJ”. Press SEL knob to confirm, then “A-VOL” will be displayed. At this time, rotate SEL knob to set the volume level you need. This will be the preset sound level for unit. Then every time the unit will be turned on with this volume level. Leave the unit idle for the new setting to take effect. RCA output The RCA output jack is on the back of the unit. This output is for connecting amplifier, equalizer, or other audio device. Follow the manufacturers i
ملخص المحتوى في الصفحة رقم 15
Radio operations Choose Radio Band Press BAND button to activate the Radio mode. The unit is equipped with 3 FM bands (FM1, FM2 and FM3) and 2 AM bands (MW1 and MW2). Each of the bands can store up to 6 preset stations, making total 30 preset memory stations. Radio Tune/Seek Function In Radio mode, press PREV/NEXT buttons to manually adjust the radio frequency. Auto seek modes Press and hold SEL knob until “TA SEEK” is shown on the display, then press SEL knob to cycle through the menu selection
ملخص المحتوى في الصفحة رقم 16
Save Your Preset Stations There are six numbered preset buttons, which can store and recall stations for each band. While listening to a radio station you would like to save as a preset, press and hold one of the buttons numbered 1-6 until you hear a beep. The button you pressed is now the preset button for that station. Automatic Store/Preset Scan 1. Automatic scan and store: while listening to the FM Radio, press F/PS button. The receiver will automatically scan the saved stations of that FM b
ملخص المحتوى في الصفحة رقم 17
RDS operations Following functions are available for radio FM band mode. RDS-EON Control This unit is equipped with the latest technology of EON control, so that when you are listening to Radio or CD, if there is any travel announcement from a nearby local station, the radio will already know the frequency of that radio station. Then it will receive the station, turn up the volume, or interrupt the playback of the music for the duration of the announcement. At the end of the announcement the rad
ملخص المحتوى في الصفحة رقم 18
PTY – Program type This radio will allow you to select the type of program required, and will search for a station broadcasting that type of program. Press PTY button once to show the music type. Then press numbered 1-6 buttons to choose different music types available. Press the PTY button twice to show the speech type program. Then press 1-6 button to choose the different speech type program. Each number button will show 3 different speech program for you to choose. MASK DPI/MASK ALL Press and
ملخص المحتوى في الصفحة رقم 19
CD/MP3/WMA operations Electronic Shock Protection (ESP) The electronic shock protection is ideal for driving uneven road. For MP3 discs Electronic Skip Protection for MP3 discs is a default feature. Please note that this feature supports the CDs with songs encoded by 96 Kb/s and 32000 Hz. For songs encoded in higher quality, the anti-shock duration will decrease proportionally to the file size. For CD discs Press and hold SEL knob for 2 seconds, the display will show “TA SEEK”. Press the knob ag
ملخص المحتوى في الصفحة رقم 20
MP3 Track search mode You can use the 4 search modes to find your favorite MP3 songs. The search modes work only with MP3 discs. Simple search Press PREV/NEXT buttons to choose your song. Press the 5/DN10 and 6/UP10 button to advance 10 songs up or down. Track search Press F/PS button and the display will show “TRK SCH”. At this moment, press SEL knob so that “TRK” will blink on the display. Then rotate the knob to choose your desired track and press the knob again to confirm the selection. The
