ملخص المحتوى في الصفحة رقم 1
Operator′s manual
333RJ 335RJ
X-series
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
E E E En n n ng g g glllliiiis s s sh h h h
ملخص المحتوى في الصفحة رقم 2
15 m 50FT KEY TO SYMBOLS Symbols Noise emission to the environment according to the European Community’s Directive. The machine’s emission is WARNING! Clearing saws, brushcutters specified in chapter Technical data and on and trimmers can be dangerous! Careless label. or incorrect use can result in serious or fatal injury to the operator or others. 1. Please read the operator’s manual carefully and make sure you understand 2. the instr
ملخص المحتوى في الصفحة رقم 3
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Please read the operator’s manual carefully. Symbols ....................................................................... 2 CONTENTS WARNING! Long-term exposure to noise can Contents ...................................................................... 3 result in permanent hearing impairment. So ! Note the following before starting: ..............................
ملخص المحتوى في الصفحة رقم 4
INTRODUCTION Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a l
ملخص المحتوى في الصفحة رقم 5
WHAT IS WHAT? What is what on the clearing saw? 1 Trimmer head 17 Choke control 2 Grease filler cap, bevel gear 18 Air purge 3 Bevel gear 19 Locking nut 4 Cutting attachment guard 20 Support flange 5 Shaft 21 Support cup 6 Handle adjustment 22 Blade 7 Loop handle 23 Drive disc 8 Suspension ring 24 Transport guard 9 Stop switch 25 Spark plug spanner 10 Throttle lock 26 Locking pin 11 Throttle control 27 Socket spanner 12 Spark plug cap and spark plug 2
ملخص المحتوى في الصفحة رقم 6
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or The only accessories you can operate with this engine unit fatal injury to the operator or others. It is extremely are the cutting attachments we recommend in the chapter important that you read and understand the contents
ملخص المحتوى في الصفحة رقم 7
GENERAL SAFETY PRECAUTIONS CLOTHING Make sure the throttle control is locked at the idle setting when the throttle lock is released. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby. Press the throttle lock and make sure it returns to its o
ملخص المحتوى في الصفحة رقم 8
GENERAL SAFETY PRECAUTIONS Check that the vibration damping element is undamaged and Cutting attachment guard securely attached. WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage This guard is intended to prevent loose objects from being ! in people who have impaired circulation. thrown towards the operator. The guard also protects the Contact your doctor if you experience operator from accidental contact with the cutting attachment. symptoms of overe
ملخص المحتوى في الصفحة رقم 9
GENERAL SAFETY PRECAUTIONS If the muffler on your machine is fitted with a spark arrestor Cutting equipment mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious This section describes how to choose and maintain your damage. cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting performance. • Extend the life of cutting equipment. IMPORTANT! Only use cutting attachments with the guards we WARNING! Muffl
ملخص المحتوى في الصفحة رقم 10
GENERAL SAFETY PRECAUTIONS General rules Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly Only use cutting attachments with the guards we around the drum, otherwise the machine will generate recommend! See the chapter on Technical data. harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY Fitting the J-handle Assembling the cutting equipment • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. WARNING! When fitting the cutting attachment it is ! extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. • Slide the spacer into
ملخص المحتوى في الصفحة رقم 12
ASSEMBLY Fitting a blade guard, grass blade Fitting other guards and cutting and grass cutter attachments • Fit the trimmer guard/combination guard (A) intended for G use with the trimmer head/plastic blades. CAUTION! F Ensure that the guard extension is fitted. E Hang the trimmer guard/combination guard (A) on the two D hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locki
ملخص المحتوى في الصفحة رقم 13
FUEL HANDLING Petrol Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. CAUTION! Always use a quality petrol/oil mixture at least 90 octane (RON). If your machine is equipped with a catalytic 2 If you have spilt fuel on yourself or your clothes, change converter (see chapter on Technical data) always use a good your clothes. Wash any part of your body that has come in quality unleaded petrol/oil mixture. Leaded
ملخص المحتوى في الصفحة رقم 14
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. WARNING! Taking the following precautions, will lessen the risk of fire: • Mix (shake) the fuel mixture thoroughly before filling the ! machine’s fuel tank. Do not smoke or place hot objects near fuel. Always shut off the engin
ملخص المحتوى في الصفحة رقم 15
STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most WARNING! The complete clutch cover and common reason why cracks are formed is that sharp shaft must be fitted before the machine is ! corners have been formed at the bottom of the teeth while started, otherwise the clutch can come loose sharpening or that the blade has been used with dull and cause personal inju
ملخص المحتوى في الصفحة رقم 16
STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a machine with damaged spark plug cap. Stopping Stop the engine by switching off the ignition. CAUTION! The stop switch autom
ملخص المحتوى في الصفحة رقم 17
WORKING TECHNIQUES 6 Keep the cutting attachment below waist level. General working instructions 7 Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the IMPORTANT! equipment any distance. This section describes the basic safety precautions for 8 Never put the machine down with the engine running working with clearing saws and trimmers. unless you have it in clear sight. If you encounter a situation where you are uncertain how to pro
ملخص المحتوى في الصفحة رقم 18
WORKING TECHNIQUES Clearing Grass clearing using a grass blade • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases • Grass blades and grass cutters must not be used on the wear on the cord. woody stems. • A grass blade is used for all types of tall or coarse grass. • The grass is cut down with a sideways, swingi
ملخص المحتوى في الصفحة رقم 19
MAINTENANCE Basic setting Carburettor • The basic carburettor settings are adjusted during testing Your Husqvarna product has been designed and at the factory. The basic setting is richer than the optimal manufactured to specifications that reduce harmful setting and should be maintained for the first few hours the emissions. After the engine has used 8-10 tanks of fuel the machine is in use. The carburettor should then be finely engine will be run-in. To ensure that it continues to run at p
ملخص المحتوى في الصفحة رقم 20
MAINTENANCE Fine adjustment of the idle speed T Correctly adjusted carburettor Adjust the idle speed using the idle adjustment screw T, if it is When the carburettor is correctly adjusted the machine will necessary to readjust. First turn the idle adjustment screw T accelerate without hesitation and burble a little at maximum clockwise until the cutting attachment starts to rotate. Then speed. It is also important that the cutting attachment does turn the screw anticlockwise until the cutting
