ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
How to install your Midland mobile CB .................................. 3 Installation and operating accessories furnished with your Midland CB: ................................................................................................... 3 Where to locate your CB transceiver. ............................................... 3 Mechanical mounting. ...................................................................... 4 Power wiring ( negative ground only). ..........................
ملخص المحتوى في الصفحة رقم 3
Welcome to the world of Midland electronics Congratulations. You have just purchased a state of the art mobile CB radio. In the years ahead, you can expect to realize-time and again the real reasons and meaning of the front running position Midland holds among CB users everywhere. You will come to know that Midland power is more than just a slogan, but the heading of long list of hearable, seeable benefits. As your Midland CB experience unfolds and grows we hope you will remember that C
ملخص المحتوى في الصفحة رقم 4
Safety and convenience are the primary considerations in deciding exactly where to locate your radio. Caution: Be sure that the unit is located so that it does not interfere with the driver, supplemental restraint systems (air bags), or impair access to any controls. Connecting cables must be routed and secured in such a manner as not to interfere with the operation of the brake, accelerator or other controls. Interference from either the unit or connecting cables may contribute to
ملخص المحتوى في الصفحة رقم 5
Step 4 Locate and secure the radio into the mounting bracket, allowing working space for later power connections. Power wiring ( negative ground only). Step 1: If you have not determined whether your vehicle has a negative or positive ground, do so now. Then disconnect the negative lead from the battery to prevent short circuits that can occur during wiring. Do not connect this transceiver to positive ground electrical systems. Step 2: With negative ground A.connect the positiv
ملخص المحتوى في الصفحة رقم 6
Installation of microphone hanger. Mounting holes are provided on the microphone hanger bracket. The bracket can be attached to the vehicle dash, or other convenient location. Antenna: How to select, position install and tune the right one for you. Basically, you may choose from two types of mobile CB antennas - full-length whip and loaded whip - and a variety of of mounts (depending on where you locate your antenna). Midland markets a broad line of high-performance antennas.
ملخص المحتوى في الصفحة رقم 7
Antenna installation. Follow the manufacturer’s installation instructions carefully. Warning: Never operate your CB radio without attaching an antenna or with a broken antenna cable. This will result in damage to transmitter circuitry. Safety notice: The antenna used for this radio must be installed to provide a separation distance of at least 20cm (8 in.) from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter. Tuning your
ملخص المحتوى في الصفحة رقم 8
Midland MODEL 4001 CB Operating controls FRONT PANEL CONTROLS ON/OFF VOLUME: In the off position your transceiver power is off. Turn this control clockwise to switch on the unit and adjust the volume. SQUELCH CONTROL: Adjust this control until background noise just disappears. If the control is adjusted too far clockwise it may cause muting of weaker signals. RF GAIN CONTROL: Adjust this control counter-clockwise to reduce reception of interfering signa
ملخص المحتوى في الصفحة رقم 9
MIC GAIN CONTROL: Adjust this control to suit individual voice characteristics and ambient noise conditions to provide maximum intelligibility. S/RF POWER METER: This meter is used in receiveing to indicate the relative signal strength of incoming signals. When transmitting, it shows RF power output. BRIGHT/DIM Switch: When turned to DIM, the meter backlight and control knob backlight intensitiy is reduced. ANL/OFF Switch: When turned on it operates in the receiver to reduce a
ملخص المحتوى في الصفحة رقم 10
BACK PANEL ANTENNA CONNECTOR: Connect a standard 50-ohm CB antenna to this connector. EXT SP: When a speaker is connected to this jack the internal speaker is by-passed. All received signals will be heard through the external speaker. The speaker connected to the “EXT” jack should be rated at 8 ohms and 5 watts. PA JACK An optional PA speaker may be attached to your transceiver through the PA output jack on the back panel. This allows you to communicate with pedestrians
ملخص المحتوى في الصفحة رقم 11
Power Supply ....................................................................13.8 VDC negative ground Size ……………………………………………………4-7/8”(W) x 6-1/2”(D) x 1-1/2”(H) Unit Weight…………………………………………………………………….1 lb. 10 oz. RECEIVER ( CB, 26.965-27.405 MHz ) Sensitivity at 10db S/N......................................................................................0.7 uV Selectivity ...........................................................................................45 dB + 10 kHz Squel
ملخص المحتوى في الصفحة رقم 12
Midland Radio Corporation Hereby certifies that this unit has been designed, manufactured, FCC type accepted and certified in accordance with part 95 and Part 15, Subpart C of the current FCC rules and regulations as of the date of manufacture. ___________________________________________________________________ LIMITED WARRANTY. Midland Radio will repair or replace, at its option without charge, your MODEL 4001 CB transceiver which fails due to a defect in material or workmansh
