ملخص المحتوى في الصفحة رقم 1
ATD-7343
3 TON LOW PROFILE ALUMINUM FLOOR JACK
USER’S MANUAL
Specifications:
Capacity: 3 Tons Chassis Width: 13"
Min Height: 3.75" Saddle Diameter: 4.52"
Max Height: 18.1" Net Weight: 55 lbs
Length: 26.4"
This hydraulic jack conforms to all “ANSI / ASME” safety standards.
ملخص المحتوى في الصفحة رقم 2
SAFETY WARNING AND PRECAUTIONS General Safety Warnings: WARNING: The instructions and warnings contained in this manual should be read and understood before using or operating this tool. Do not allow anyone to use or operate this tool until they have read this manual and have the following instructions could developed a thorough understanding of how this tool works. Failure to observe any of result in severe personal injury to tool user and bystanders, or cause damage to the tool and pro
ملخص المحتوى في الصفحة رقم 3
WARNING: Ensure that there are no persons inside the vehicle to be lifted. Switch off the engine and apply the brake. Chock each unlifted tire in BOTH directions as shown below. WARNING: Position the jack under the manufacturer's recommended lifting point for the vehicle. Off centered loads can slip and accidents may result. WARNING: During raising and lowering of the load, precautions should be taken to avoid movement of the vehicle. WARNING: Traffic may cause the raised vehicle to roc
ملخص المحتوى في الصفحة رقم 4
Support the vehicle with appropriate jack stands. Lift the vehicle to remove the jack stands, ensuring that there are no persons or obstructions under the vehicle. Turn the handle counter‐clockwise. MAINTENANCE: Important: Both the maintenance and repair of the jack may only be performed by qualified persons, who have sufficient knowledge of the hydraulic system used in these jacks Regularly lubricate the moving parts in the wheels, arms, handle and pump roller pin. Only o
ملخص المحتوى في الصفحة رقم 5
TROUBLESHOOTING: CAUTION: To prevent personal injury, all inspection, maintenance, and repair procedures must be performed when the jack is free of load. Trouble Cause Solution 1. Release valve is open 1. Verify the release valve is closed. Release valve may need cleaning 2. Low/no hydraulic fluid in 2. Fill with approved hydraulic reservoir fluid and bleed system 3. Air trapped in hydraulic 3. Follow the purge air system procedure Jack Does Not Lift 4. Load is a
ملخص المحتوى في الصفحة رقم 6
ATD-7343 ITEM# ORDERING PART# PART DESCRIPTION ITEM# ORDERING PART# PART DESCRIPTION 1 PRT7343-01 P01 - SADDLE PAD 11 PRT7343-11 P11 - NUT, M12 2 PRT7343-02 P02 - SADDLE SCREW 12 PRT7343-12 P12 - HANDLE YOLK 3 PRT7343-03 P03 - SADDLE 13 PRT7343-13 P13 - HANDLE SET SCREW 4 PRT7343-04 P04 - SADDLE BASE 14 PRT7343-14 P14 - HANDLE, UPPER SECTION 5 PRT7343-05 P05 - LIFT ARM ASSEMBLY 15 PRT7343-15 P15 - HANDLE, LOWER SECTION 6 PRT7343-06 P06 - RADIUS ROD 14,15 PRT7343-HD HD - COMPLETE HANDLE ASSEMBLY
ملخص المحتوى في الصفحة رقم 7
WARRANTY 1 YEAR REPLACEMENT WARRANTY THIS WARRANTY AND CONFIRMED RECEIPT (S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES The warranty is only made available by returning the product to the point of sale. PURCHASED FROM:________________________________________________ DATE PURCHASED: ________________________________________________ INVOICE/RECIEPT NUMBER:_________________________________________ Your ATD‐7343 is warranted for a period of 12 months from the original date
