ملخص المحتوى في الصفحة رقم 1
®
CleanView II
BAGLESS
USER’S GUIDE
3574/73G8/3576/20Q9 SERIES
3 Safety Instructions
4 Product View
5-6
Assembly Instructions
6-8 Operation / Special Tools
8-12 Maintenance
12-13 Troubleshooting
14
Replacement Parts
15
Consumer Services
16 Warranty
DJ68-00280A REV(0.1)
ملخص المحتوى في الصفحة رقم 2
® Thanks For Buying A BISSELL CleanView II We’re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system. Your BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance
ملخص المحتوى في الصفحة رقم 3
IMPORTAnT SAFETy InSTRUCTIOnS When using an electrical appliance, basic unplugging vacuum cleaner. precautions should be observed, including ■ Use extra care when cleaning stairs. the following: ■ Unplug before attaching the turbobrush. ■ Do not pick up flammable materials (lighter READ ALL InSTRUCTIOnS fluid, gasoline, kerosene, etc.) or use in the BEFORE USInG y OUR presence of explosive liquids or vapors. ■ Do not pick up toxic material (chlorine bleach, UPRIGHT VACUUM. ammonia
ملخص المحتوى في الصفحة رقم 4
Cord Clip Hose Clip Handle Stretch Hose Carrying Handle Stair Cleaning Quick Release Handle Cord Wrap Power Cord Power Switch Crevice Tool ® Quick Reach Extension Wand Handle Louvers Combination Dusting Brush/ Hose Wand Upholstery Tool Upper Tank Hose Wand Base Post-Motor Dirt Container Filter Filter Cup Optional Hepa Media Filter Inner and Outer (Select Models Circular Filters Only) ™ Lock ’n Seal Foot Hose Headlight Lever Handle Release Pedal Height Adjustment Knob Furniture
ملخص المحتوى في الصفحة رقم 5
How To Put It Together The only tool you’ll need to assemble your vacuum cleaner is a screwdriver. Attach Handle To Vacuum Locate the vacuum Handle and remove the screw 1. packet taped to the base of the Handle. Stand the vacuum upright and slide the base of 2. the Handle firmly into the grooves at the top of the vacuum body. Check to be sure the Handle is fitted to the vacuum 3. body. If there is a gap in front, continue to push firmly until the Handle is flush. Insert the screw provid
ملخص المحتوى في الصفحة رقم 6
How To Use your Vacuum Handle Positions Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For storage and above floor cleaning with tools. 1. Normal Cleaning- Press Handle Release Pedal once. 2. Use for most household floor cleaning tasks. Low Cleaning- With the vacuum in normal cleaning posi- 3. tion, press Handle Release Pedal again. Use for reaching under low furniture such as tables, chairs or beds. CAUTIOn: Before using y
ملخص المحتوى في الصفحة رقم 7
Special On-Board Tools nOTICE: The Floor Brush will continue Your BISSELL CleanView II is not only a pow- to rotate while you use your erful carpet and rug vacuum cleaner, it’s also a vacuum for above floor cleaning. versatile above floor vacuum cleaner when you To prevent carpet damage, do not lean on the vacuum or let the select one of the special tools. Powerfoot tilt forward. Raise Handle to Upright Position. 1. Grasp the Quick Reach Handle and lift Hose Wand to 2. separate fro
ملخص المحتوى في الصفحة رقم 8
How To Maintain your Vacuum W ARnInG: To reduce the risk of To maintain maximum cleaning performance, the electric shock, turn Power following maintenance steps must be performed: Switch OFF and discon- nect polarized Empty the Dirt Container when the dirt reaches the 1. plug from electrical outlet “Full” line on the side. before performing maintenance or Check the Inner and Outer Circular Filters and the 2. troubleshooting checks. Pre-Motor Filter at least once a month and clean
ملخص المحتوى في الصفحة رقم 9
Cleaning The Inner & Outer Circular Filters Separate the Outer foam and Inner pleated Circular Filters. Wash each 4. individually by hand in warm water. Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. The Filter Cup may be washed in warm water with a mild detergent. 5. Make sure it is completely dry before reassembling with filters. The Upper Tank and Louvers may also be wiped clean with a damp 6. clot
ملخص المحتوى في الصفحة رقم 10
Check Rotating Floor Brush and Drive Belt Continued For standard models, remove the four screws as shown 3. with a Phillips Head Screwdriver. Lift the Brush Cover off. For wide cleaning path models, Lift tab 1 and release the three latches in order 2-4 as marked. Lift the Brush Cover off. Grasp Rotating Floor Brush at both ends and lift. 4. Clean strings, hair and other debris from Rotating Floor 5. Brush, paying particular attention to brush ends. Brush Cover Standard models only Clean strin
ملخص المحتوى في الصفحة رقم 11
Replace Lightbulb Continued Determine the light bulb type of your vacuum: 3. Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end Standard Bulb – remove the bulb from the socket by grasping 4. bulb and pulling straight out. Install the new bulb by pushing it gently into the socket until the bulb snaps into place. Large Bulb - remove the bulb from the socket by pushing bulb in gently and turning it towards brush. Install the n
ملخص المحتوى في الصفحة رقم 12
Clearing Clogs Continued Check Upper Tank and Louvers for build up or clogs. 3. Check to make sure Louvers are installed correctly. To Louvers unlock the Louvers, grasp the rim and turn toward the left. Pull straight down to remove. If the Louvers are missing or not locked into place, check and clear the tube in the center of the Dirt Container. Suction Inlet Remove the Twist ‘n Snap Hose from the vacuum by 4. turning to the left. Check the Suction Inlet, Hose and Hose Wand for clogs.
ملخص المحتوى في الصفحة رقم 13
Troubleshooting Continued Vacuum cleaner won’t pick up dirt continued Possible Causes Remedies 10 Dirt Container not installed properly 10 Position correctly and lock in place Filters are dirty Check and clean Inner and Outer 11 11 Circular Filters, Pre-Motor and Post-Motor Filters Louvers missing or installed incorrectly Check for a clog in the tube in the 12 12 center of the Dirt Container, clear and properly install Louvers Tools won't pick up dirt Possible Cause Rem
ملخص المحتوى في الصفحة رقم 14
Replacement Parts – BISSELL Cleanview II Series You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services or by visiting our website. To locate a retailer near you, or to place an order using Visa, MasterCard, Discover or American Express, call BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or visit our Website - www.bissell.com Item Part no. Part name 1 32074 Style 7/9/10 Drive Belt (2-Pack) 2 20
ملخص المحتوى في الصفحة رقم 15
BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc. PO Box 3606 Grand Rapids, MI 49501 ATTN: Consumer Services Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record y
ملخص المحتوى في الصفحة رقم 16
Warranty This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below. Limited One year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare Inc. will repair or replace (with
