ملخص المحتوى في الصفحة رقم 1
RGB SQ PROCESSOR BOARD
HKSR-5803SQ
ADVANCED HQ PROCESSOR BOARD
HKSR-5803HQ
INSTALLATION MANUAL
1st Edition
ملخص المحتوى في الصفحة رقم 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
ملخص المحتوى في الصفحة رقم 3
Section 1 Installation 1-2. Installation Overview Purpose of this manual This manual is an installation manual of RGB SQ Proces- Components sor Board HKSR-5803SQ and Advanced HQ Processor Board HKSR-5803HQ. HKSR-5803SQ is composed of the following items: This manual is intended for system and service engineers, . SQ-20 Board so describes information regarding installation. . Hexagonal support 7 mm (4 pcs) . PSW2.6 x 5.8 (8 pcs) . Installation manual Related manual Besides this installation manua
ملخص المحتوى في الصفحة رقم 4
1-3. Installation Procedure 4. Fully loosen the two fixing screws, and then remove the upper lid (rear) assembly in the arrow direction. 1. Turn off the power of the VTR. 2. Fully loosen the two fixing screws, and then slide the Fixing screw two knobs on the upper lid (front) assembly each to the Fixing screw Upper lid (rear) inside. (Move the knobs to the outside to fix the upper assembly lid (front) assembly.) Protrusion 3. Remove the upper lid (front) assembly in the arrow direction. Square
ملخص المحتوى في الصفحة رقم 5
6. Remove the six screws to detach the shield plate from 9. Reattach the shield plate to the HIF-22 board with six the HPR-22 board. screws. Shield plate Shield plate PSW PSW 2.6 x 6 2.6 x 6 PSW PSW 2.6 x 6 2.6 x 6 PSW2.6 x 6 PSW2.6 x 6 HPR-22 board HPR-22 board 7. Attach four 7 mm hexagonal supports (accessory) to the HPR-22 board with four screws (accessory). 8. Connect the SQ-20 board or DLP-27 board to the HPR-22 board and secure it with four screws (accesso- ry). PSW2.6 x 5.8 HPR-22 board H
ملخص المحتوى في الصفحة رقم 6
10. Securely insert the HPR-22 board into the “HPR” slot 1-4. Confirming Identification of to tightly connect the board to the connector on the Optional Board motherboard, while pressing down the two eject levers. Confirmation Procedure Eject lever 1. On the HOME menu, press the DIAG button while pressing the [SFT] (shift) key. The MAINTENANCE INFORMATION menu HPR-22 board appears. Eject lever ROM MAINTENANCE INFORMATION DISPLAY F1 VER OPERATION 1105HOURS[ 1105H] ERR DRUM RUNNING
ملخص المحتوى في الصفحة رقم 7
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation. Sony Corporation interdit formell
ملخص المحتوى في الصفحة رقم 8
HKSR-5803SQ (SY) Printed in Japan HKSR-5803HQ (SY) J, E Sony Corporation 2007. 10 08 3-286-478-01 ©2007
