Audiovox ACC-30 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

6
COMPACT
ACC-30
DIGITAL AUDIO 6 DISC
COMPACT DISC CHANGER
MODEL ACC-30
6-DISC CD CHANGER
INSTALLATION MANUAL

ملخص المحتوى في الصفحة رقم 2

PACKING LIST MAIN UNIT Changer 6 COMPACT ACC-30 DIGITAL AUDIO 6 DISC COMPACT DISC CHANGER INSTALLATION PARTS Hex Head Bolt with Washer Base Phillips Head (M5 x 12) Mounting Bracket Screw 4 pcs. 4 pcs. 2 pcs. Screw Hole Cover Labels 5 Meter Din Cable Mounting Angle Adjustment Tool 1 pc. 1 pc. 1 pc. ACCESSORIES CD Magazine Index seal sheet Installation Manual Owner's guide 1 pc. 1 pc. 1 pc. 1 pc. 1

ملخص المحتوى في الصفحة رقم 3

BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the 4 transport screws. Be sure to remove the screws prior to installation. Retain these screws for future use when transporting the unit for service/maintenance. l Caution l After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Pre

ملخص المحتوى في الصفحة رقم 4

H 45° V H 45° V INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45° ANGLE INSTALLATION Set the anti-vibration springs to Se

ملخص المحتوى في الصفحة رقم 5

H 45° V PROCEDURE FOR VERTICAL INSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Set the anti-vibration springs to position "V". Attach a mounting bracket to each side of the unit, using 1 2 the hex head bolts with washer base. position "V" Bracket Bracket Hex head bolt with washer base Determine the mounting location, and drill four mounting 4 Mount the unit in place, using four self-tapping Phill

ملخص المحتوى في الصفحة رقم 6

H 45° V PROCEDURE FOR 45° ANGLE INSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. Set the anti-vibration springs to position "45°". Attach a mounting bracket to each side of the unit, using 1 2 the 4 hex head bolts with washer base. position "45°" Bracket Bracket Hex head bolt with washer base 45° Determine the mounting location, and drill four mounting 4 Mount the unit in place, using four self-t

ملخص المحتوى في الصفحة رقم 7

DIN cable (8-pin) WIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see Note below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Rampage/Audiovox audio dealer to be sure your stereo is directly compatible with this CD changer. 2. When used with Rampage model AV-427 car stereo, be sure Changer Selector switch on bottom of radio chassis is set to position "B". 6

ملخص المحتوى في الصفحة رقم 8

© 1999 Audiovox Corporation, Happauge, N.Y. 11788 Printed in Korea 128-5572