ملخص المحتوى في الصفحة رقم 1
TABLE OF CONTENTS
FOR YOUR SAFETY---------------------------------------------- 1
User's Manual
SAFETY PRECAUTIONS -------------------------------------- 2
SPECIAL NOTES ON LCD MONITORS -------------------------- 3
BEFORE YOU OPERATE THE MONITOR ---------------------------- 3
FEATURES -------------------------------------------------- 3
PACKING LIST --------------------------------------------- 4
17” LCD MONITOR
OPERATING INSTRUCTIONS ---------------------
ملخص المحتوى في الصفحة رقم 2
Before operating the monitor please read this manual thoroughly. This manunl should be PRECAUTIONS retained for future reference. ?? Do not use the monitor near water, or lay it at a moisture place. FCC Class B Radio Frequency Interference Statement ?? Openings in the back of the cabinet are provided for ventilation. To ensure reliable WARNING:(FOR FCC CERTIFIED MODELS) operation of the monitor and to protect it from overheating,be sure these openings are NOTE:This equipment has been tested
ملخص المحتوى في الصفحة رقم 3
SPECIAL NOTES ON LCD MONITORS POWERCORD The following symptoms are normal with LCD monitor and do not indicate a problem. Power Source: 1.Make sure the power cord is the correct type that required in your area. NOTES 2.This LCD monitor has a universal power supply that allows operation in either 100/120V ?? Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn AC or 220/240V AC voltage area(No user adjustment is required.) off the Power Switch and then
ملخص المحتوى في الصفحة رقم 4
FRONT PANEL CONTROL HOW TO ADJUST A SETTING 1.Press the MENU button to activate the OSD window. See figure 5. ?? Power Key: 2.Press ? or? to select the desired function. 3.Press the MENU button to select the function that you want to adjust. Press this button to switch ON/OFF of monitor's power. 4.Press? or? to change the settings of the current function. ?? MENU/Enter: 5.To exit and save, select the exit functions, or leave the monitor alone for 15 seconds. If you Activates t
ملخص المحتوى في الصفحة رقم 5
2.6 Exit 2.Press”AUTO”button(at front pane) about 2 seconds, the monitor will do all the adjustment 3. Function automatically. You can adjust the image manually, If the screen has a flicker or blur, or not 3.1Auto Adjust fit in the display Reset to original factory geometry setting 3.2Auto Colour 3.press ALT-F, and then X to exit from the Dos-Editor screen Reset to original factory color setting 3.3Exit If the DOS-MODE characters still have distortion
ملخص المحتوى في الصفحة رقم 6
When there is no video input signal this monitor, following a time-out period, will hitting the CAPS LOCK key. automatically switch to an OFF mode. This reduces the monitor's internal power supply Missing one of the primary Inspect the monitor's video cable and make sure that none consumption. After the video input signal is restored, full power is restored and the display is colors(RED,GREEN,or BLUE) of the pins are bent. automatically redrawn. The appearance is similar to a “Screen Save
ملخص المحتوى في الصفحة رقم 7
APPENDIX ERROR MESSAGE AND POSSIBLE SOLUTION SPECIFICATIONS CABLE NOT CONNECTED : Driving system TFT Color LCD 1.Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. Size 43cm(17”) 2.Check the signal-cable’s connection pins for damage. Pixel pitch 0.264mm(H)×0.264MM(V) LCD Panel Viewable angle 140° (H)130° (V) INPUT NOT SUPPORT: Response time 16ms Your computer has been set to unsuitable display mode, Set the
ملخص المحتوى في الصفحة رقم 8
13 14 ?? Auto Adjust Key/Exit FACTORY PRESET TIMING TABLE ?? Brightness Switch ?? Contrast HORIZONTAL VERTICAL STANDARD RESOLUTION ?? Power Key FREQUENCY FREQUENCY ?? MENU/Enter 720×400 31.47 kHz 70.00 Hz ?? Brightness 640×480 31.469 kHz 60.00 Hz VGA External Controls: 640×480 37.861 kHz 72.00 Hz ?? Geometry 640×480 37.5 kHz 75.00 Hz ?? Color 800×600 35.156 kHz 56.00 Hz Functions ?? Language 800×60
ملخص المحتوى في الصفحة رقم 9
15 9
